LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Suzuki >> 2007 >> Swift + >> Repair and Diagnosis >> Electrical >> Instrument Panel System Displays And Gauges >> Diagnostic Information and Procedures >> DTC P0462 >> Test Description
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Test Description

The number below refers to the step number on the diagnostic table.

  1. 2:  This step determines if the fault is present.
DTC P0462

Step Action Value Yes No
Schematic Reference:  Instrument Cluster Schematics (Notchback)   or  Instrument Cluster Schematics (Hatchback)  
Connector End View Reference: Displays and Gages Connector End Views 
1 Did you perform the Diagnostic System Check - Vehicle? - Go to Step 2  Go to Diagnostic System Check - Vehicle
2 
  1. Turn ON the ignition, with the engine OFF.
  2. Observe the Fuel Level Sensor voltage parameter with a scan tool.
Is the voltage more than the specified value?		 4.25 V Go to Step 4  Go to Step 3 
3
  1. Observe the Freeze Frame/Failure Records for this DTC.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.
Did the DTC fail this ignition?		 - Go to Step 4  Go to Diagnostic Aids
4
  1. Turn OFF the ignition.
  2. Disconnect the fuel level sensor through the access panel under the rear seat.
  3. Turn ON the ignition, with the engine OFF.
  4. Observe the Fuel Level Sensor voltage parameter with a scan tool.
Is the voltage less than the specified value?		 4.25 V Go to Step 6  Go to Step 5 
5 Test the signal circuit of the fuel level sensor for a short to ground. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?		 - Go to Step 10  Go to Step 7 
6 Test for shorted terminals and poor connections at the fuel level sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?		 - Go to Step 10  Go to Step 8 
7 Test for shorted terminals and poor connections at the engine control module (ECM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?		 - Go to Step 10  Go to Step 9 
8 Replace the fuel sender assembly. Refer to the following:
  • Fuel Pump Replacement in for the 1.2L engine
  • Fuel Pump Replacement for the 1.4L DOHC engine
  • Fuel Pump Replacement for the 1.4L SOHC engine
  • Fuel Pump Replacement for the 1.5L engine
  • Fuel Sender Assembly Replacement for the 1.6L engine

Did you complete the replacement?		 - Go to Step 10  -
9 Replace the control module. Refer to the following:
  • Engine Control Module Replacement for the 1.2L engine
  • Engine Control Module Replacement for the 1.4L DOHC engine
  • Engine Control Module Replacement for the 1.4L SOHC engine
  • Engine Control Module Replacement for the 1.5L engine
  • Engine Control Module Replacement for the 1.6L engine

Did you complete the replacement?		 - Go to Step 10  -
10
  1. Clear the DTCs with a scan tool.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.
Did the DTC fail this ignition?		 - Go to Step 2  Go to Step 11 
11 Observe the Capture Info with a scan tool.
Are there any DTCs that have not been diagnosed?		 - Diagnostic Trouble Code (DTC) List - Vehicle System OK
scientia non olet · About LEMON Manuals