Scan Tool Data
Reference: SCAN TOOL DATA DEFINITIONS
As the data values given in the following table are standard values estimated on the basis of values obtained from the normally operating vehicles by using a scan tool, use them as reference values. Even when the vehicle is in good condition, there may be cases where the checked value does not fall within each specified data range. Therefore, judgment as abnormal should not be made by checking with these data alone.
Also, condition in the following table that can be checked by the scan tool are those detected by 4WD control module and output from 4WD control module as commands and there may be cases where the transfer or actuator is not operating (in the condition) as indicated by the scan tool.
NOTE:
The following scan tool data related to 4WD control system can be checked only by communicating with 4WD control module.
SCAN TOOL DATA
| Scan Tool Data | Condition | Normal Condition / Reference Value |
|---|---|---|
| Vehicle Speed | At vehicle stop | < 5 KM/H (< 8 MPH) |
| Engine Speed | At idling with no load after warming up | Desired idle speed ± 50 r/min |
| 2WD/4WD Switch | "2WD <--> 4WD" switch released | OFF |
| Ignition switch ON, "2WD <--> 4WD" switch kept pushing | ON | |
| 2WD/4WD indicator | Transfer shifted to 2H position | 2WD |
| Transfer shifted to 4H or 4L position | 4WD | |
| Transfer shifted to N position | Neutral | |
| Neutral switch | "N" switch released | OFF |
| "N" switch kept pushing | ON | |
| Neutral switch indicator | Transfer shifted to other than N position | OFF |
| Transfer shifted to N position | ON | |
| 4L switch | "4L" switch button released | OFF |
| "4L" switch button kept in pushing | ON | |
| 4L Sw indicator | Transfer shifted to other than 4L position | OFF |
| Transfer shifted to 4L position | ON | |
| Reminder buzzer | Buzzer not being sounded | OFF |
| Buzzer being sounded | ON | |
| T/F fork switch | Transfer shifted to 2H or N position | OFF |
| Transfer shifted to 4H or 4L position | ON | |
| 4L switch | Transfer shifted to 2H or 4H position | OFF |
| Transfer shifted to N or 4L position | ON | |
| 4WD switch | Transfer shifted to 4H, N or 4L position | OFF |
| Transfer shifted to 2H position | ON | |
| T/F shift Pos sensor | Transfer shifted to 2H position | 2H |
| Transfer shifted to 4H position | 4H | |
| Transfer shifted to N position | N | |
| Transfer shifted to 4L position | 4L | |
| Transfer being shifted | Invalid | |
| T/F shift actuator | Transfer shift actuator motor being rotated in 2H --> 4L direction when transfer shifted from 2H to 4H position | 4L side |
| Transfer shift actuator motor being rotated in 4L --> 2H direction when transfer shifted from 4H to 2H position | 2H side | |
| Transfer shift actuator motor is in other than above-mentioned condition | Neutral | |
| Axle lock actuator | Front axle lock actuator motor being rotated in lock direction when transfer shifted from 2H to 4H position | Lock |
| Front axle lock actuator motor being rotated in unlock direction when transfer shifted from 4H to 2H position | Unlock | |
| Front axle lock actuator motor is in other than above-mentioned condition | Neutral | |
| Actuator Pos Sen | Transfer shifted to 2H position | 2H |
| Transfer shifted to 4H position | 4H | |
| Transfer shifted to N position | N | |
| Transfer shifted to 4L position | 4L | |
| Transfer being shifted between 2H and 4H position | 2H - 4H | |
| Transfer being shifted between 4H and N position | 4H - N | |
| Transfer being shifted between N and 4L position | N - 4L | |
| Actuator motor Pos | Transfer shifted to 2H position | 2H |
| Transfer shifted to 4H position | 4H | |
| Transfer shifted to N position | N | |
| Transfer shifted to 4L position | 4L | |
| Transfer being shifted | Shift | |
| Battery Voltage | - | 10 - 14 V |
| CPP switch (MT) | Clutch pedal depressed | OFF |
| Clutch pedal released | ON | |
| N range switch (AT) | A/T shifted to "N" range | ON |
| A/T shifted to other than "N" range | OFF | |
| 4WD signal for ABS | Transfer shifted to 2H or N position | 2WD |
| Transfer shifted to 4H or 4L position | 4WD |