Fuel Pressure Sensor - G247-, CHECKING

WARNING: This page is about a different car, the 2022 Volkswagen Atlas Cross Sport, 2021 Volkswagen Atlas Cross Sport, and 2020 Volkswagen Atlas Cross Sport. However, it is still accessible from the selected car via links, so may be relevant.

General Description

The Fuel Pressure Sensor -G247- measures the fuel pressure in the high-pressure fuel system. The Engine Control Module -J623- analyzes the signal and regulates the fuel high pressure through the Fuel Pressure Regulator Valve -N276- in the high-pressure pump.

Special tools and workshop equipment required

Multimeter.
Wiring Diagram.
Scan Tool.

Test requirements

Fuses OK.
Battery voltage OK.
Switch OFF all electrical and electronic accessories.
Vehicles with Auto. Transmission, ensure Selector Lever position is in "P".
Vehicles with Man. Transmission, ensure Shifter Lever position is in "N" with Parking Brake applied.
Observe all safety precautions. Refer to: SAFETY PRECAUTIONS .
View clean working conditions. Refer to: CLEAN WORKING CONDITIONS .

Test Procedure

Step	Procedure	Result / Action to Take
1	PERFORM: Preliminary Check to verify the customers complaint. Refer to: PRELIMINARY CHECK . -- Was Complaint verified?	-- YES: GO TO: Step 2 Fuel Pressure Sensor - G247-, CHECKING - 2 . -- NO: GATHER more information from customer about the complaint.
2	IGNITION: OFF. DISCONNECT: Fuel Pressure Sensor -G247- harness connector. IGNITION: ON. CHECK: Fuel Pressure Sensor -G247- harness connector terminals 1 to 3 for voltage. SPECIFIED VALUE: About 5.0 V. IGNITION: OFF. -- Was Value obtained?	-- YES: GO TO: Step 3 Fuel Pressure Sensor - G247-, CHECKING - 3 . -- NO: GO TO: Step 4 Fuel Pressure Sensor - G247-, CHECKING - 4 .
3	REMOVE: Engine Control Module - J623-. Refer to appropriate repair information. CHECK: Fuel Pressure Sensor -G247- harness connector terminal 2 to the Engine Control Module - J623- harness connector T105 / 49 for resistance. SPECIFIED VALUE: 0.5 Ω (± 0.3 Ω). -- Was Value obtained?	-- YES: REPLACE: Fuel Pressure Sensor -G247-. Refer to appropriate repair information. GO TO: Step 5 Fuel Pressure Sensor - G247-, CHECKING - 5 . -- NO: PERFORM: Visual Inspection of wiring and component. CHECK: Wiring for open, high resistance, short or harness connector for damage, corrosion, loose or broken terminals. REPAIR: Faulty wiring or connector. GO TO: Step 5 Fuel Pressure Sensor - G247-, CHECKING - 5 .
4	REMOVE: Engine Control Module - J623-. Refer to appropriate repair information. CHECK: Fuel Pressure Sensor -G247- harness connector terminal 1 to the Engine Control Module - J623- harness connector T105 / 11 for resistance. CHECK: Fuel Pressure Sensor -G247- harness connector terminal 3 to the Engine Control Module - J623- harness connector T105 / 68 for resistance. SPECIFIED VALUE: 0.5 Ω (± 0.3 Ω). -- Were Values obtained?	-- YES: GO TO: Step 5 Fuel Pressure Sensor - G247-, CHECKING - 5 . -- NO: PERFORM: Visual Inspection of wiring and component. CHECK: Wiring for open, high resistance, short or harness connector for damage, corrosion, loose or broken terminals. REPAIR: Faulty wiring or connector. GO TO: Step 5 Fuel Pressure Sensor - G247-, CHECKING - 5 .
5	Final Procedure Perform a road test to verify repair. -- Does the original DTC return?	-- YES: CHECK: Engine Control Module -J623- harness connector for any damaged, pushed-out pins. REPAIR: As necessary. If all electrical connections are OK: REPLACE: Engine Control Module -J623-. Refer to appropriate repair information. Clear the DTC's. Refer to: DIAGNOSTIC MODE 04 - ERASE DTC MEMORY . Repair is complete. Generate Readiness Code. Refer to: READINESS CODE . Return vehicle to Customer. -- NO: Perform the diagnostic procedure for any DTC's. If no DTC's return the repair is complete. Return vehicle to customer.