Transmission, Removing, Vehicles With 3.6L Engine

Special tools and workshop equipment required

Engine Support Bridge: 10-222A

Fig 1: Engine Support Bridge 10-222A
Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.
Adapter: 10-222A/35
Engine Support Bridge - Engine Support 18: 10-222A/18

Fig 2: Identifying Special Tools And Workshop Equipment
Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.
Engine/Gearbox Support Shackle: 10-222A/12

Fig 3: Engine/Gearbox Support Shackle (10-222A/12)
Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.
Transmission Support - Pins 29: 3282/29

Fig 4: Identifying Pin
Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.
Transmission Support: 3282

Fig 5: Transmission Support 3282
Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.
Engine and Gearbox Jack: VAS6931

Fig 6: Engine and Gearbox Jack VAS6931 or VAG1383A
Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.
Engine Bung Set: VAS6122

Fig 7: Engine Bung Set
Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.
Insert Tool - 18mm: T10509 or Insert Tool - 18mm: T10179

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.
Socket - Xzn 14: T10061

Fig 8: Identifying Socket
Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.
Engine Support Bridge - Engine Support 3: 10-222A/3

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.
Counterhold - Multiple Use: T10172A

Fig 9: Counterhold - Kit - Multiple Use T10172
Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.
Engine Crane Adapter - Bracket: T10013

Fig 10: Bracket T10013
Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.
Engine Support Bridge - Engine Support 19: 10-222A/19

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.
Engine Support - Basic Set - Square Pipe: T40091/1

Fig 11: Engine Support - Basic Set T40091
Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.
Engine Support - Joint Fixture: T40091/3
Engine Support Device - Gearbox Bracket: T10346/1

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.
Engine Support - Automatic Transmission Adapter: 10-222A/16

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.
Engine Sling - Engine Bracket: 2024A/1

Fig 12: Engine Sling - Engine Bracket
Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.
Tensioning Strap: T10038 (quantity: 2)

Fig 13: Identifying Tensioning Strap T10038
Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.
Not illustrated: Socket - Sw15: V/175

Removing

-- Move the selector lever to >>P<<.

-- Remove the air filter housing. Refer to AIR FILTER HOUSING, REMOVING AND INSTALLING (2.0L) or AIR FILTER HOUSING, REMOVING AND INSTALLING (3.6L) .

-- Remove the battery and battery tray. Refer to OVERVIEW - BATTERY .

-- Pry the selector lever cable -1- off the selector lever -2-, for example, using a wrench.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Disconnect the connector -6- from the Multifunction Transmission Range Switch -F125- and free up the wire at the bracket.

-- Remove the bolts -5- from the cable bracket -4-. Do not remove the lock washer -3-.

-- Disengage the gearshift lever cable -1- from the clip -2-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

NOTE:

Do not bend or kink the selector lever cable.

So that the cable is not damaged when removing and installing the transmission, use, for example, a cable tie to secure the cable on the body in a suitable position.

-- Remove the starter. Refer to STARTER, REMOVING AND INSTALLING .

-- Remove the upper bolts -arrows- connecting the transmission to the engine, for example, with a 12-point flex head socket wrench.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the bracket for coolant hoses, so that the >>rear<< spindle from the engine support bridge has enough >>clearance<<.

-- Disconnect any hoses and cables located near the engine lifting eyes for the Engine Support Bridge: 10-222A .

-- Attach the Engine Support Bridge: 10-222A as shown. The base -11- from the Engine Support Bridge - Engine Support 19: 10-222A/19 -10- is supported by the longitudinal member seam.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

The following are needed:

Adapter: 10-222A/35 -1- (quantity: 2)
Spindle from the Engine Support Bridge: 10-222A -2- (quantity: 3)
Engine Support - Joint Fixture: T40091/3 -3-
Square Pipe: T40091/1 -4-
Engine Support Bridge - Engine Support 3: 10-222A/3 -5-
Engine Crane Adapter - Bracket: T10013 -6-
Square pipe from Engine Support Bridge: 10-222A -7-
Engine/Gearbox Support Shackle: 10-222A/12 -8-
Engine Support Bridge - Engine Support 18: 10-222A/18 -9-
Engine Support Bridge - Engine Support 19: 10-222A/19 -10- with base -11-
Engine Sling - Engine Bracket: 2024A/1
Engine Support Bridge - Gearbox Bracket: T10346
Engine Support Device - Gearbox Bracket: T10346/1
M6 x 40 collar bolt

Also slide the Engine Support - Automatic Transmission Adapter: 10-222A/16 onto the left side of the Engine Support Bridge. Refer to Fig 14.
When the Engine Support Bridge is complete, the Engine Support - Automatic Transmission Adapter: 10-222A/16 is located between the Engine Support Bridge - Engine Support 18: 10-222A/18 and the left Adapter: 10-222A/35 .
The Engine Support - Automatic Transmission Adapter: 10-222A/16 secures the Engine Support Bridge later in the procedure.

-- Push the Engine Support Bridge - Engine Support 18: 10-222A/18 and Engine Support Bridge - Engine Support 3: 10-222A/3 onto the Engine Support Bridge: 10-222A .

Secure the Engine Support Bridge 10-222A as Shown

Fig 14: Secure the : 10-222A as Shown

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Fasten the Engine Support Bridge - Gearbox Bracket: T10346 or Engine Support Device - Gearbox Bracket: T10346/1 to the left rear locating hole for the battery tray.

-- Use a M6 x 40 collar bolt or one of the bolts for the battery tray.

NOTE:

Attach the Engine/Gearbox Support Shackle: 10-222A/12 to the topmost hole on the Engine Sling - Engine Bracket: 2024A/1 .

-- Secure the Engine Sling - Engine Bracket: 2024A/1 with the securing pin -arrow-.

-- Then engage the Spindles in the engine lifting eyes.

-- Lightly pretension the engine/transmission assembly and Engine Support Bridge using the Spindles.

-- Remove the noise insulation. Refer to OVERVIEW - NOISE INSULATION .

-- Remove the left front wheel housing liner. Refer to OVERVIEW - FRONT WHEEL HOUSING LINER .

-- Remove the connector from the transmission as follows Push the retainer -1- in the direction of the -arrow-, open the hook -2- and then remove the connector -3- from the transmission.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the bolt -arrow A- and the ATF lines -2- from the thermostat -1-. The bolts - B arrows - are not removed.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Seal the ATF lines and connections on the thermostat with suitable plugs taken from the Engine Bung Set: VAS6122 .

Remove the subframe. Refer to OVERVIEW - SUBFRAME .

-- Remove the right and left drive axle from the transmission. Refer to DRIVE AXLE, REMOVING AND INSTALLING .

-- Secure both drive axles to the suspension strut using the Tensioning Strap: T10038 .

Fig 15: Identifying Ratchet Strap On Right Drive Axle

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

Do not damage the surface protection of the shafts.

AWD Vehicles

-- Remove the bevel box. Refer to BEVEL BOX, REMOVING, VEHICLES WITH 3.6L, 206 KW ENGINE .

Continuation for All Vehicles

-- Remove the six converter nuts -arrow- with the Socket - Sw15: V/175 .

Fig 16: Torque Converter

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- To do so, turn the engine an additional 60° in the direction of engine rotation -arrow- using the Counterhold - Multiple Use: T10172A .

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

NOTE:

If all six torque converter nuts are not removed, the torque converter will be pulled out when removing the transmission from the engine!

Use the Crankshaft Adapter: T03003 to counterhold at the belt pulley/vibration damper when loosening the torque converter nuts.

-- Remove the transmission/fluid pan bolts -arrows-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the front bolts for attaching the engine to the transmission -1-. The upper bolt is secured with a nut -arrow-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the bolts -arrows- from the left subframe mount for the transmission.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Lower the engine/transmission as far as dimension -a- using the spindles on the Engine Support Bridge: 10-222A .

Fig 17: Turing Spindles On 10 - 222 A And Lower Transmission To Dimension

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-a- = Approximately 70 mm

The transmission is disconnected from the engine in this position.

-- Place the Transmission Support: 3282 -A- on the Engine and Gearbox Jack: VAS6931 -B-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

Install the Transmission Support: 3282 on the transmission as follows with the Mounting Elements:

The Engine and Gearbox Jack with Transmission Support is positioned under the transmission -1- so that the spindle -left arrow- points forward in the direction of travel.
The spindle -right arrow- points in the direction of travel to the left.
The Mounts -C- are positioned in the groove surrounding the transmission fluid pan as shown.
The Pin -D- locks in the recess on the front right side of the transmission.

-- Install the Transmission Support - Pins 29: 3282/29 -A- into the rear hole for the pendulum support bolt on the transmission -1-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Support the transmission by carefully lifting it using the Engine and Gearbox Jack.

-- Remove the last engine/transmission connecting bolt -arrow-.

-- Pry up the transmission -3- from the engine at the same time push the torque converter -1- against the transmission in the direction of -arrow- using for example a screwdriver -2-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Carefully drain the transmission, ensure >>clearance<< to other components.

-- After the removing the transmission, secure the torque converter from falling. Refer to Fig 18.

Fig 18: Securing Torque Converter

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Install the transmission. Refer to TRANSMISSION, INSTALLING .