Transmission Control Module --

WARNING: This page is about a different car, the 2022 Volkswagen Atlas Cross Sport, 2021 Volkswagen Atlas Cross Sport, and 2020 Volkswagen Atlas Cross Sport. However, it is still accessible from the selected car via links, so may be relevant.

DQ-381-7
DTC	Fault Code Description	Monitor Strategy Description	Malfunction Criteria	Threshold Value	Secondary Parameters with Enable Conditions	Monitoring Time Length	Frequency of checks, MIL Illum
P0501	Vehicle Speed Sensor "A" Circuit Range/Performance	Speed sensor shaft 1 rationality check	Difference between measured and calculated output speed for shaft 1 And Difference between output shaft speed 1 and shaft 2	> 150 RPM And > 150 RPM	Input shaft speeds for shafts 1 and 2 > 100 RPM	2.0 s Continuous	2 DCY
P0560	System Voltage	Supply voltage monitoring stage 1 signal range check	Internal sensor supply voltage	> 5.5 V Or < 4.5		2.0 s Continuous	2 DCY
						Supply voltage monitoring stage 2 signal range check
P0562	System Voltage Low	Supply voltage monitoring signal range check	Voltage And One of the following monitors is in protective function P0750, P0765, P0760, P0755, P0745, P0775, P0795, P0770, P2706	< 8.0 V		5.0 s Continuous	2 DCY
P0563	System Voltage High	Supply voltage monitoring signal range check	Voltage	> 18.0 V		2.0 s Continuous	2 DCY
P0607	Control Module Performance	TCM safety monitor function check	Traction in the opposite driving direction			2.0 s Continuous	2 DCY
						Too low gear selected and clutch closed
						Too low gear selected
						Two gears on one shaft
						Both clutches closed
						Incorrect clutch actuation
P0614	ECM/TCM Incompatible	Flexray rationality check	Information of transmission code is faulty		Ignition on	2.0 s Continuous	2 DCY
		Information of engine code is faulty		Ignition on				2.0 s Continuous	2 DCY
P062F	Internal Control Module EEPROM Error	TCM rationality check	Comparison of EEProm date - both copies	invalid	When reading a datablock active	2.0 s Continuous	2 DCY
TCM memory check			Comparison of stored value - both copies
			Write ability check faulty
P0666	Control Module Internal Temperature Sensor "A" Circuit	TCM temperature sensor circuit continuity check	TCM temperature sensor self check TCM temperature sensor	failed invalid state	Ignition on TCM temperature sensor initialization finished	2.0 s Continuous	2 DCY
				TCM temperature sensor at And Actual chip temperature Or Actual chip temperature			-0.03125° C And < -24° C Or > 24° C
P0667	Control Module Internal Temperature Sensor "A" Range/Performance	TCM temperature sensor rationality check	Difference between TCM Temperature Sensor and internal chip temperature	26 > x > -26° C	Ignition on TCM temperature sensor initialization finished	2.0 s Continuous	2 DCY
Difference between actual TCM temperature sensor and filtered temperature				> 8° C	Ignition on
P06A6	Sensor Reference Voltage "A" Circuit Range/Performance	TCM internal driver a circuit continuity check	Voltage	2.0 V		2.0 s Continuous	2 DCY
P06A7	Sensor Reference Voltage "B" Circuit Range/Performance	TCM internal driver b circuit continuity check	Voltage	2.0 V		2.0 s Continuous	2 DCY
P06A8	Sensor Reference Voltage "C" Circuit Range/Performance	TCM internal driver c circuit continuity check	Voltage	2.0 V		2.0 s Continuous	2 DCY
P06A9	Sensor Reference Voltage "D" Circuit Range/Performance	Supply voltage monitoring signal range check	Internal sensor supply voltage	< 9.0 V		2.0 s Continuous	2 DCY
P06D5	Sensor Reference Voltage "E" Circuit Range/Performance	Supply voltage monitoring stage 3 signal range check	Internal sensor supply voltage	> 5.5 V Or < 4.5 [-]		2.0 s Continuous	2 DCY
P0700	Transmission Control System (MIL Request)	TCM functional check	CPU permanent shutdown of all actors	active		2.0 s Continuous	2 DCY
P0702	Transmission Control System Electrical	TCM internal driver a circuit continuity check	Internal voltage	failure		2.0 s Continuous	2 DCY
TCM internal driver b circuit continuity check			Internal voltage	failure	2.0 s Continuous					2 DCY
TCM internal driver c circuit continuity check			Internal voltage	failure	2.0 s Continuous					2 DCY
P0711	Transmission Fluid Temperature Sensor "A" Circuit Range/Performance	TCM temperature sensor rationality check	Actual ATF temperature	> 170° C < -50° C	Power supply voltage 6.0 - 18.0 V	2.0 s Continuous	2 DCY
TCM temperature sensor circuit continuity check			Difference between actual ATF temperature and filtered temperature	> 15° C
P0712	Transmission Fluid Temperature Sensor "A" Circuit Low	TCM temperature sensor rationality check	Short circuit to ground	< 0.16 V	Power supply voltage 6.0 - 18.0 V	2.0 s Continuous	2 DCY
P0713	Transmission Fluid Temperature Sensor "A" Circuit High	TCM temperature sensor rationality check	Short circuit to high	> 4.7 V	Power supply voltage 6.0 - 18.0 V	2.0 s Continuous	2 DCY
P0716	Input/Turbine Shaft Speed Sensor "A" Circuit Range/Performance	Speed sensor shaft 1 signal range check	Input shaft speed for shaft 1	> 12, 000 RPM		2.0 s Continuous	2 DCY
P0718	Input/Turbine Shaft Speed Sensor "A" Circuit Intermittent	Speed sensor shaft 1 rationality check	No signal	> 1.0 s	Ignition on	2.0 s Continuous	2 DCY
P0745	Pressure Control Solenoid "A"	Solenoid for clutch 1 circuit continuity check	Difference between set current and measured current	> 100.0 mA		2.0 s Continuous	2 DCY
P0748	Pressure Control Solenoid "A" Electrical	Solenoid for clutch 1 circuit continuity check	Internal voltage failure			2.0 s Continuous	2 DCY
P0750	Shift Solenoid "A"	Solenoid for gear 1-3 circuit continuity check	Difference between set current and measured current	> 100.0 mA		2.0 s Continuous	2 DCY
P0753	Shift Solenoid "A" Electrical	Solenoid for gear 1-3 circuit continuity check	Internal voltage failure			2.0 s Continuous	2 DCY
P0755	Shift Solenoid "B"	Solenoid for gear 2-R circuit continuity check	Difference between set current and measured current	> 100.0 mA		2.0 s Continuous	2 DCY
P0758	Shift Solenoid "B" Electrical	Solenoid for gear 2-R circuit continuity check	Internal voltage failure			2.0 s Continuous	2 DCY
P0760	Shift Solenoid "C"	Solenoid for gear 5-7 circuit continuity check	Difference between set current and measured current	> 100.0 mA		2.0 s Continuous	2 DCY
P0763	Shift Solenoid "C" Electrical	Solenoid for gear 5-7 circuit continuity check	Internal voltage failure			2.0 s Continuous	2 DCY
P0765	Shift Solenoid "D"	Solenoid for gear 4-6 circuit continuity check	Difference between set current and measured current	> 100.0 mA		2.0 s Continuous	2 DCY
P0768	Shift Solenoid "D" Electrical	Solenoid for gear 4-6 circuit continuity check	Internal voltage failure			2.0 s Continuous	2 DCY
P0770	Shift Solenoid "E"	Solenoid for cooling circuit continuity check	Difference between set current and measured current	> 100.0 mA		2.0 s Continuous	2 DCY
P0773	Shift Solenoid "E" Electrical	Solenoid for cooling circuit continuity check	Internal voltage failure			2.0 s Continuous	2 DCY
P0775	Pressure Control Solenoid "B"	Solenoid for clutch 2 circuit continuity check	Difference between set current and measured current	> 100.0 mA		2.0 s Continuous	2 DCY
P0778	Pressure Control Solenoid "B" Electrical	Solenoid for clutch 2 circuit continuity check	Internal voltage failure			2.0 s Continuous	2 DCY
P0795	Pressure Control Solenoid "C"	Solenoid for main pressure circuit continuity check	Difference between set current and measured current	> 100.0 mA		2.0 s Continuous	2 DCY
P0798	Pressure Control Solenoid "C" Electrical	Solenoid for main pressure circuit continuity check	Internal voltage failure			2.0 s Continuous	2 DCY
P0811	Excessive Clutch "A" Slippage	Drive-off clutch 1 rationality check	Clutch slippage was detected	> 150 RPM	Clutch state is drive	2.0 s Continuous	2 DCY
P081E	Excessive Clutch "B" Slippage	Drive-off clutch 2 rationality check	Clutch slippage was detected	> 150 RPM	Clutch state is drive	2.0 s Continuous	2 DCY
P0B0A	Electric/Auxiliary Transmission Fluid Pump "A" Motor Supply Voltage Circuit Low	(Electrical) ATF pump signal range check	Voltage And P0B0D is in protective function	< 10.0 V		2.0 s Continuous	2 DCY
P0B0D	Electric/Auxiliary Transmission Fluid Pump Motor Control Module	(Electrical) ATF pump signal range check	Difference between actual and commanded ATF pump speed	> 500 RPM	Calibration not active	2.0 s Continuous	2 DCY
P0C28	Electric/Auxiliary Transmission Fluid Pump "A" Motor Current High	(Electrical) ATF pump functional check	ATF pump over current protection	active		2.0 s Continuous	2 DCY
P0C29	Electric/Auxiliary Transmission Fluid Pump "A" Driver Circuit Performance	(Electrical) ATF pump control module circuit continuity check	Electrical failure in power amplifier (endtsufe)			2.0 s Continuous	2 DCY
						Driver error
						Overload ATF pump
P0C2A	Electric/Auxiliary Transmission Fluid Pump "A" Motor Stalled	(Electrical) ATF pump functional check	Current ATF pump speed < And Set current for ATF pump control	300 RPM And 30.0 - 50.0 A	ATF pump governor enabled And Target ATF- engine speed > 300 RPM	2.0 s Continuous	2 DCY
P0C2C	Electric/Auxiliary Transmission Fluid Pump Control Module Feedback Signal Range/Performance	ATF pump speed sensor rationality check	Sensor output sin² +cos²	> 0.8 or < 1.2 [-]	Sensor supply voltage 4.5 - 5.5 V	2.0 s Continuous	2 DCY
P0C2D	Electric/Auxiliary Transmission Fluid Pump Control Module Feedback Signal Low	ATF pump speed sensor signal range check	Sensor output voltage	< 0.25 V	Sensor supply voltage 4.5 - 5.5 V	2.0 s Continuous	2 DCY
P0C2E	Electric/Auxiliary Transmission Fluid Pump Control Module Feedback Signal High	ATF pump speed sensor signal range check	Sensor output voltage	> 4.5 V	Sensor supply voltage 4.5 - 5.5 V	2.0 s Continuous	2 DCY
P187A	Gear Selector 1 Engaging Process Not Successful	Gear actuator 1-3 functional check	Time out in gear actuator state synchronize	> 2.0 s	Gear actuator 1-3 nominal state is synchronize	2.0 s Continuous	2 DCY
Time out in gear actuator state after synchronization				> 1.0 s	Gear actuator 1-3 nominal state is after synchronization
				Time out in gear actuator state unlatched			Gear actuator 1-3 nominal state is unlatched
				Time out in gear actuator state engage			Gear actuator 1-3 nominal state is engage
Gear shift module 1 - 3 functional check			Difference between measured and synchronize shaft speed 1 And Gear actuator 1-3 movement	> 300 RPM And > 7 mm or < -7 mm	Shaft 1 and 2 in sync position
P187B	Gear Selector 2 Engaging Process Not Successful	Gear actuator 2-R functional check	Time out in gear actuator state synchronize	> 2.0 s	Gear actuator 2-R nominal state is synchronize	2.0 s Continuous	2 DCY
Time out in gear actuator state after synchronization				> 1.0 s	Gear actuator 2-R nominal state is after synchronization
				Time out in gear actuator state unlatched			Gear actuator 2-R nominal state is unlatched
				Time out in gear actuator state engage			Gear actuator 2-R nominal state is engage
Gear shift module 2-R functional check			Difference between measured and synchronize shaft speed 1 And Gear actuator 2-R movement	> 300 RPM And > 7 mm or < -7 mm	Shaft 1 and 2 in sync position
P187C	Gear Selector 3 Engaging Process Not Successful	Gear actuator 5-7 functional check	Time out in gear actuator state synchronize	> 2.0 s	Gear actuator 5-7 nominal state is synchronize	2.0 s Continuous	2 DCY
Time out in gear actuator state after synchronization				> 1.0 s	Gear actuator 5-7 nominal state is after synchronization
				Time out in gear actuator state unlatched			Gear actuator 5-7 nominal state is unlatched
				Time out in gear actuator state engage			Gear actuator 5-7 nominal state is engage
Gear shift module 5-7 functional check			Difference between measured and synchronize shaft speed 1 And Gear actuator 5-7 movement	> 300 RPM And > 7 mm or < -7 mm	Shaft 1 and 2 in sync position
P187D	Gear Selector 4 Engaging Process Not Successful	Gear actuator 4-6 functional check	Time out in gear actuator state synchronize	> 2.0 s	Gear actuator 4-6 nominal state is synchronize	2.0 s Continuous	2 DCY
Time out in gear actuator state after synchronization				> 1.0 s	Gear actuator 4-6 nominal state is after synchronization
				Time out in gear actuator state unlatched			Gear actuator 4-6 nominal state is unlatched
				Time out in gear actuator state engage			Gear actuator 4-6 nominal state is engage
Gear shift module 4-6 functional check			Difference between measured and synchronize shaft speed 1 And Gear actuator 4-6 movement	> 300 RPM And > 7 mm or < -7 mm	Shaft 1 and 2 in sync position
P2159	Vehicle Speed Sensor "B" Circuit Range/Performance	Speed sensor shaft 2 rationality check	Difference between measured and calculated output speed for shaft 2 And Difference between output shaft speed 1 and shaft 2	> 150 RPM And > 150 RPM	Input shaft speeds for shafts 1 and 2 > 100 RPM	2.0 s Continuous	2 DCY
P2162	Vehicle Speed Sensor "A"/"B" Correlation	Speed sensor shaft 1 and shaft 2 rationality check	Difference between output shaft speeds and input speeds shafts 1 and 2	> 150 RPM	Input shaft speeds for shafts 1 and 2 > 100 RPM And Engaged gear position is not neutral	2.0 s Continuous	2 DCY
P2706	Shift Solenoid "F"	Solenoid for overpressure reduction circuit continuity check	Difference between set current and measured current	> 100.0 mA		2.0 s Continuous	2 DCY
P2709	Shift Solenoid "F" Electrical	Solenoid for overpressure reduction circuit continuity check	Internal voltage	failure		2.0 s Continuous	2 DCY
P2766	Input/Turbine Shaft Speed Sensor "B" Circuit Range/Performance	Speed sensor shaft 2 signal range check	Input shaft speed for shaft 2	> 12, 000 RPM		2.0 s Continuous	2 DCY
P2768	Input/Turbine Shaft Speed Sensor "B" Circuit Intermittent	Speed sensor shaft 2 rationality check	No signal	> 1.0 s	Ignition on	2.0 s Continuous	2 DCY
P2831	Shift Fork "A" Position Circuit	Gear shift module 1 - 3 signal range check	No signal	> 1.0 s		2.0 s Continuous	2 DCY
P2832	Shift Fork "A" Position Circuit Range/Performance	Gear shift module 1 - 3 signal range check	Duty - cycle position sensor	> 92.5% < 7.5%	Sensor supply voltage between 4.5 - 5.5 V	2.0 s Continuous	2 DCY
				Time of oscillation			< 0.9 ms > 1.1 ms
P2836	Shift Fork "B" Position Circuit	Gear shift module 2 - R signal range check	No signal	> 1.0 s		2.0 s Continuous	2 DCY
P2837	Shift Fork "B" Position Circuit Range/Performance	Gear shift module 2 - R signal range check	Duty - cycle position sensor	> 92.5% < 7.5%	Sensor supply voltage between 4.5 - 5.5 V	2.0 s Continuous	2 DCY
				Time of oscillation			< 0.9 ms > 1.1 ms
P283B	Shift Fork "C" Position Circuit	Gear shift module 5 - 7 signal range check	No signal	> 1.0 s		2.0 s Continuous	2 DCY
P283C	Shift Fork "C" Position Circuit Range/Performance	Gear shift module 5 - 7 signal range check	Duty - cycle position sensor	> 92.5% < 7.5%	Sensor supply voltage between 4.5 - 5.5 V	2.0 s Continuous	2 DCY
				Time of oscillation			< 0.9 ms > 1.1 ms
P2840	Shift Fork "D" Position Circuit	Gear shift module 4 - 6 signal range check	No signal	> 1.0 s		2.0 s Continuous	2 DCY
P2841	Shift Fork "D" Position Circuit Range/Performance	Gear shift module 4 - 6 signal range check	Duty - cycle position sensor	> 92.5% < 7.5%	Sensor supply voltage between 4.5 - 5.5 V	2.0 s Continuous	2 DCY
				Time of oscillation			< 0.9 ms > 1.1 ms
P2845	Shift Fork "A" Position Sensor Incorrect Neutral Position Indicated	Gear actuator 1-3 functional check	Gear actuator 1-3 leaves the neutral - position	> 3.0 mm	Gear actuator 1-3 nominal state is neutral	2.0 s Continuous	2 DCY
P2846	Shift Fork "B" Position Sensor Incorrect Neutral Position Indicated	Gear actuator 2-R functional check	Gear actuator 2-R leaves the neutral - position	> 3.0 mm	Gear actuator 2-R nominal state is neutral	2.0 s Continuous	2 DCY
P2847	Shift Fork "C" Position Sensor Incorrect Neutral Position Indicated	Gear actuator 5-7 functional check	Gear actuator 5-7 leaves the neutral - position	> 3.0 mm	Gear actuator 5-7 nominal state is neutral	2.0 s Continuous	2 DCY
P2848	Shift Fork "D" Position Sensor Incorrect Neutral Position Indicated	Gear actuator 4-6 functional check	Gear actuator 4-6 leaves the neutral - position	> 3.0 mm	Gear actuator 4-6 nominal state is neutral	2.0 s Continuous	2 DCY
P2849	Shift Fork "A" Stuck	Gear actuator 1-3 functional check	Time out in gear actuator state disengage	> 2.0 s	Gear actuator 1-3 nominal state is disengage	2.0 s Continuous	2 DCY
P284A	Shift Fork "B" Stuck	Gear actuator 2-R functional check	Time out in gear actuator state disengage	> 2.0 s	Gear actuator 2-R nominal state is disengage	2.0 s Continuous	2 DCY
P284B	Shift Fork "C" Stuck	Gear actuator 5-7 functional check	Time out in gear actuator state disengage	> 2.0 s	Gear actuator 5-7 nominal state is disengage	2.0 s Continuous	2 DCY
P284C	Shift Fork "D" Stuck	Gear actuator 4-6 functional check	Time out in gear actuator state disengage	> 2.0 s	Gear actuator 4-6 nominal state is disengage	2.0 s Continuous	2 DCY
P284D	Shift Fork "A" Unrequested Movement	Gear actuator 1-3 functional check	Loaded gear leaves the engage - position	> 3.0 mm	Gear actuator 1-3 nominal state is engaged	2.0 s Continuous	2 DCY
Gear actuator 1-3 leaves the engage - position				> 1.0 s
P284E	Shift Fork "B" Unrequested Movement	Gear actuator 2-R functional check	Loaded gear leaves the engage - position	> 3.0 mm	Gear actuator 2-R nominal state is engaged	2.0 s Continuous	2 DCY
				Gear actuator 2-R leaves the engage - position			> 1.0 s
P284F	Shift Fork "C" Unrequested Movement	Gear actuator 5-7 functional check	Loaded gear leaves the engage - position	> 3.0 mm	Gear actuator 5-7 nominal state is engaged	2.0 s Continuous	2 DCY
				Gear actuator 5-7 leaves the engage - position			> 1.0 s
P2850	Shift Fork "D" Unrequested Movement	Gear actuator 4-6 functional check	Loaded gear leaves the engage - position	> 3.0 mm	Gear actuator 4-6 nominal state is engaged	2.0 s Continuous	2 DCY
				Gear actuator 4-6 leaves the engage - position			> 1.0 s
U0080	Vehicle Communication Bus F	Flexray communication check	Flexray synchronization is faulty		Ignition on	2.0 s Continuous	2 DCY
U0100	Lost Communication With ECM/PCM "A"	Flexray communication check	Engine control module	no signal	Ignition on	2.0 s Continuous	2 DCY
U0121	Lost Communication With Anti-Lock Brake System (ABS) Control Module "A"	Flexray communication check	Anti-lock brake system	no signal	Ignition on	2.0 s Continuous	2 DCY
U0401	Invalid Data Received From ECM/PCM "A"	Flexray communication check	Invalid data received from engine control module		Ignition on	2.0 s Continuous	2 DCY
U0415	Invalid Data Received From Anti-Lock Brake System (ABS) Control Module "A"	Flexray communication check	Invalid data received from anti-lock brake system		Ignition on	2.0 s Continuous	2 DCY
U1103	Control Module Vehicle Options Error	TCM functional check	Production mode	active		2.0 s Continuous	2 DCY