Rear Motor, Removing

Special tools and workshop equipment required 

• Pins:3282/34 
• Pins:3282/45 
• Transmission Support:3282 
• Transmission Support - Mounting Plate 49:3282/49 
• Engine and Gearbox Jack:VAS 6931 
• Socket - Xzn 16:T10198 
• Engine Bung Set:VAS 6122 

Three-Phase Current Drive -VX54- with Electric Drive Power and Control Electronics -JX1- will be subsequently called motor.

Removing

-- Refer to High-Voltage System, De-Energizing .

-- Remove the rear center underbody trim panels -1-. Refer to REAR CENTER UNDERBODY TRIM PANEL, REMOVING AND INSTALLING .

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the rear underbody trim panels -2-. Refer to REAR UNDERBODY TRIM PANEL, REMOVING AND INSTALLING .

-- Remove the spring link stone chip protection -4-. Refer to SPRING LINK STONE CHIP PROTECTION, REMOVING AND INSTALLING .

-- Remove the left and right drive axle. Refer to DRIVE AXLE, REMOVING AND INSTALLING .

-- Remove the left rear wheel housing liner. Refer to REAR WHEEL HOUSING LINER, REMOVING AND INSTALLING .

-- Refer to Coolant, Draining .

Tip

Removal of the charger is necessary, to replace the transmission mount bolt.

-- Remove the High-Voltage Battery Charger 1 -AX4-. Refer to High-Voltage Battery Charger 1 AX4, Removing and Installing .

-- Open the hose clamp -arrow- and remove the coolant hose -1-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Disconnect the connector -2-.

-- Remove the nut -arrow- and the potential equalization cable bracket -1-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Unclip the coolant hose -1- -arrow-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Unclip the breather line for the transmission -1- in the left rear wheel housing -arrows-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the bolts -arrows- for the cable guide for the high-voltage cable -1- on the transmission side.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Place the Transmission Support:3282  -D- on the Engine and Gearbox Jack:VAS 6931  -E-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Position the engine and gearbox jack -E- in the center underneath the motor with the transmission -2-.

-- Install the following adapters in the mounts:

A -  Bolt :3282/34 

B -  Bolt :3282/45  with a screwed-on nut -1-

C -  Hook :3282/49 

-- Align the mounts -A- and -B- to the mounting points in the motor and transmission.

-- Position the mount -C- under the Electric Drive Power and Control Electronics -JX1-.

-- Slightly lift the motor with the transmission, so that the load is off the motor mount.

-- Remove the bolts -1- for the left and right side of the motor mount using the Socket - Xzn 16:T10198  , through the opening in the longitudinal member -arrow-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the transmission mount bolt -arrow-.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Lower the motor together with the transmission approximately 150 mm.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Remove the high-voltage cable -1- from the Electric Drive Power and Control Electronics -JX1-. For this, remove the bolts -2- and -3- above the transmission.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Open the locking bracket -A- on the high-voltage connector -4- and remove the high-voltage connector. Refer to High-Voltage Connectors, Disconnecting .

-- Unclip the coolant hose -1- -arrow A- above the transmission.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Raise the locking mechanism -2- and remove the coolant hose.

-- Unclip the breather line for the transmission -3- -arrow B- from the transmission.

-- Lower the motor with the transmission.

-- Seal the open connections on the motor and transmission with plugs from the Engine Bung Set:VAS 6122  .