Disassembly And Assembly: Halfshaft: Assembly

WARNING: This page is about a different car, the 2017 Lincoln Navigator. However, it is still accessible from the selected car via links, so may be relevant.

1.

Position the outboard boot on the shaft.

Courtesy of FORD MOTOR COMPANY

2.

Pack the outboard CV joint with 165 g (5.82 oz) of grease.
- 1.
  
  Use CV joint grease or equivalent provided in the boot kit.
- 2.
  
  Spread any remaining grease from the kit evenly inside the boot.

Courtesy of FORD MOTOR COMPANY

3.

Install the outboard boot.
- 1.
  
  Clean the boot mounting surface.
- 2.
  
  Seat the boot in the joint boot groove.

Courtesy of FORD MOTOR COMPANY

4.

Using a suitable boot clamp installer (such as Snap-On ® stock #YA3050 or equivalent) install the large boot clamp.

Courtesy of FORD MOTOR COMPANY

5.

Using a suitable boot clamp installer (such as Snap-On ® stock #YA3080 or equivalent) install the small boot clamp.

Courtesy of FORD MOTOR COMPANY

6.

Position the boot clamp on the shaft.

Courtesy of FORD MOTOR COMPANY

7.

Position the inboard boot on the shaft.

Courtesy of FORD MOTOR COMPANY

8.

Position the ball cage on the shaft with the tapered end facing the boot.

Courtesy of FORD MOTOR COMPANY

9.

NOTE: Align the index marks.

Position the inner race on the shaft with the counterbored end facing the boot.

Courtesy of FORD MOTOR COMPANY

10.

Install the snap ring.

Courtesy of FORD MOTOR COMPANY

11.

Lubricate and position the 6 balls.
- Use CV joint grease or equivalent provided in the boot kit.

Courtesy of FORD MOTOR COMPANY

12.

Fill the inboard CV joint housing with 195 g (6.88 oz) of grease.
- Use CV joint grease or equivalent provided in the boot kit.

Courtesy of FORD MOTOR COMPANY

13.

Position the boot clamp on the inboard CV joint housing.

Courtesy of FORD MOTOR COMPANY

14.

Position the inboard CV joint housing on the ball and race assembly.

Courtesy of FORD MOTOR COMPANY

15.

Install the retaining ring.

Courtesy of FORD MOTOR COMPANY

16.

Remove any excess grease from the mating surface. Seat the boot in the joint boot groove.

Courtesy of FORD MOTOR COMPANY

17.

Set the halfshaft assembled length to specification. Refer to Specifications .

Courtesy of FORD MOTOR COMPANY

18.

NOTE: Use care when inserting the screwdriver or damage to the boot may occur.

Insert a dull screwdriver blade under the boot to release the pressure.

Courtesy of FORD MOTOR COMPANY

19.

Using a suitable boot clamp installer (such as Snap-On ® stock #YA3050 or equivalent) install the large boot clamp.

Courtesy of FORD MOTOR COMPANY

20.

Using a suitable boot clamp installer (such as Snap-On ® stock #YA3080 or equivalent) install the small boot clamp.

Courtesy of FORD MOTOR COMPANY

21.

NOTE: Maintain a clean work surface.

Compress the Integrated Wheel End(IWE) disconnect on the bench to collapse the vacuum chamber.

Courtesy of FORD MOTOR COMPANY

22.

While the IWE disconnect is collapsed, install a vacuum cap on the vacuum port.

Courtesy of FORD MOTOR COMPANY

23.

NOTE: Do not install the Integrated Wheel End(IWE) end disconnect in the knuckle. It must be installed on the outer Constant Velocity (CV) joint housing or damage to the component may occur.

Install the IWE disconnect on the outer CV joint housing.

Courtesy of FORD MOTOR COMPANY

24.

NOTE: Verify the spline engagement by checking for spline lash before installing the halfshaft nut or damage to the component may occur.

Install the halfshaft in the vehicle. Refer to Halfshaft .