Rearview Camera -R189-, Calibrating

-- Set-up requirements, refer to CALIBRATION REQUIREMENTS .

-- Connect the Vehicle Diagnostic Tester.

Calibration Tool - Wheel Center Mountings :VAS6350/1  installing:

-- Check the dimension of the holes.

-- Equip the Calibration Tool - Wheel Center Mountings :VAS6350/1  appropriately. Use spacer pieces.

-- To do so, secure three wheel bolt adapters in the hole circle to each Calibration Tool - Wheel Center Mountings :VAS6350/1  .

-- Place the paddle on both Calibration Tool - Wheel Center Mountings :VAS6350/1  and secure them using a clamping screw.

-- Place the Calibration Tool - Wheel Center Mountings :VAS6350/1  onto the wheel bolts on the rear wheels.

The Calibration Tool - Wheel Center Mountings :VAS6350/1  are positioned by the "O rings" in the adapters and held in place.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Adjust the paddle with aid of lock bolts so that they move freely just above the floor. Make sure that the paddle is easily accessible.

-- Install and align the Calibration Tool :VAS6350  , refer to calibration Tool .

Distance Measurement:

-- Switch on the Calibration Tool - Spacing Laser :VAS6350/2  .

The following display appears:

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

The display shows how to stop the Calibration Tool - Spacing Laser :VAS6350/2  . Press the corresponding button.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

1. Attach with front edge
2. Attach with rear edge

-- Hold the Calibration Tool - Spacing Laser :VAS6350/2  -2- flush in the bracket on one side of the calibration board (attach with rear edge). The Calibration Tool - Spacing Laser :VAS6350/2  -2- must sit securely on the bracket.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Press the measuring button briefly.

The Laser Turns On.

-- Make sure that laser beam from Calibration Tool - Spacing Laser :VAS6350/2  -2- hits lower, enlarged part of paddle -1-.

If this is not the case, paddles must be corrected accordingly via clamping screws on the Calibration Tool - Wheel Center Mountings :VAS6350/1  .

-- Use one hand to secure the Calibration Tool - Spacing Laser :VAS6350/2  in the bracket on the Calibration Tool :VAS6350  while the laser beam is visible on the paddle.

-- Then press the measuring button for distance measurement briefly.

-- Write down the value.

-- Repeat this measurement on the other side of the Calibration Tool :VAS6350  in the same way for the rear wheel.

The distance value must be the same on both sides.

If values are not identical:

-- Align the Calibration Tool :VAS6350  long enough so that both sides are identical.

Pay attention when aligning the Calibration Tool :VAS6350  , that the Calibration Tool - Linear Laser :VAS6350/3  from the Calibration Tool :VAS6350  strikes the center of the Audi rings and the indicator of the level remains centered. Adjust if necessary.

Dimension Measurement -H- :

-- Measure the height of the Calibration Tool :VAS6350  , dimension -H- (top edge platform - floor).

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

Make sure the Calibration Tool - Spacing Laser :VAS6350/2  is adjusted correctly (attach with front edge).

The display shows how to stop the Calibration Tool - Spacing Laser :VAS6350/2  . Press the corresponding button.

Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

1. Attach with front edge
2. Attach with rear edge

Enter the height and distance dimensions into the Vehicle Diagnostic Tester in "millimeters".

Performing Calibration

Vehicle Diagnostic Tester Is Attached.

-- Select Guided Fault Finding  .

-- Select "vehicle selection" from the menu for the corresponding vehicle data.

-- Using GO TO  select the following menu points:

• Function/Component Selection
• Body
• Electrical Equipment
• 01  - OBD-capable systems
• 6C  - Rearview camera system / J772
• 6C  - rearview camera system control module, functions
• 6C  - Calibration

The Vehicle Diagnostic Tester continues with the calibrating procedure from here on.