LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Volkswagen >> 2017 >> e-Golf SE >> Repair and Diagnosis >> External Pages >> Different car >> Section 134 (Anti-Theft System - Immobilizer (Diagnostics)) >> Basic Diagnostic Procedure >> Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Basic Diagnostic Procedure: Procedure

WARNING: This page is about a different car, the 2012 Subaru Forester. However, it is still accessible from the selected car via links, so may be relevant.
DIAGNOSTIC PROCEDURE CHART

Step Check Yes No
1 CHECK SECURITY INDICATOR LIGHT. 
  1. Turn the ignition switch to "OFF" or "ACC".
  2. Wait at least 60 seconds.
 Does the security indicator light blink? Go to step 2  . Check the security indicator light circuit. < Refer to CHECK SECURITY INDICATOR LIGHT CIRCUIT , INSPECTION, Diagnostics Chart for Security Indicator Light. >
2 CHECK KEY SWITCH  .
Remove the key from ignition switch.		 Does the security indicator light begin to blink within 1 second after the key is removed? Go to step 3  . Check the key switch circuit. < Refer to CHECK KEY SWITCH CIRCUIT , INSPECTION, Diagnostics Chart for Security Indicator Light. >
3 CHECK SECURITY INDICATOR LIGHT. 
Turn the ignition switch to ON.		 Does the security indicator light go off? Go to step 5  . Go to step 4  .
4 CHECK ENGINE START. 
Turn the ignition switch to START.		 Does the starter operate? Check the LAN communication system. < Refer to BASIC DIAGNOSTIC PROCEDURE . > Go to step 7  .
5 CHECK ENGINE START. 
Turn the ignition switch to START.		 Does the starter operate? Go to step 6  . Check the LAN communication system. < Refer to BASIC DIAGNOSTIC PROCEDURE . >
6 CHECK ENGINE START. 
Turn the ignition switch to START.		 Does the engine start? Immobilizer system is normal. Go to step 8  .
7 CHECK DTC. 
  1. Turn the ignition switch to OFF.
  2. Connect the Subaru Select Monitor to data link connector. < Refer to SUBARU SELECT MONITOR . >
  3. Turn the ignition switch and Subaru Select Monitor switch to ON.
  4. Read the DTC of the body integrated unit.
 Is the DTC displayed on screen? Go to step 10  . Replace the body integrated unit < Refer to BODY INTEGRATED UNIT . > Register all ignition keys (transponders). Refer to the PC application help for Subaru Select Monitor.
8 CHECK DTC. 
  1. Turn the ignition switch to OFF.
  2. Connect the Subaru Select Monitor to data link connector. < Refer to SUBARU SELECT MONITOR . >
  3. Turn the ignition switch and Subaru Select Monitor switch to ON.
  4. Read the DTC of the ECM.
 Is the DTC displayed on screen? Go to step 9  . Perform the diagnosis for engine system. < Refer to PROCEDURE , Diagnostics for Engine Starting Failures. > < Refer to PROCEDURE , Diagnostics for Engine Starting Failure. >
9 CHECK FREEZE FRAME DATA. 
Using the Subaru Select Monitor, check the Freeze Frame Data.		 Was the Freeze Frame Data recorded? Record the data. Go to step 10  . Go to step 10  .
10 PERFORM DIAGNOSIS. 
  1. Inspect using the "Diagnostic Procedure with Diagnostic Trouble Code (DTC)". < Refer to DIAGNOSTIC PROCEDURE WITH DIAGNOSTIC TROUBLE CODE (DTC) . >
  2. Repair the trouble cause.
  3. Perform the Clear Memory Mode.
  4. Read DTCs again.
 Is the DTC displayed on screen? Inspect using the "Diagnostic Procedure with Diagnostic Trouble Code (DTC)". < Refer to DIAGNOSTIC PROCEDURE WITH DIAGNOSTIC TROUBLE CODE (DTC) . > Finish the diagnosis.
scientia non olet · About LEMON Manuals