Selector Mechanism, From 11.06

Special tools and workshop equipment required

Thrust Block T10083

Disassembling

-- Remove the shift mechanism. Refer to SHIFT MECHANISM

-- Bend the taps -arrows- on the shift mechanism base plate down with a screwdriver and remove the base plate (the tabs in the front area of the base plate are not shown).

Fig 1: Identifying Tabs On Shift Mechanism Base Plate

Courtesy of VOLKSWAGEN UNITED STATES, INC.

-- Remove the seal from the shift housing.

-- Remove shift cable and selector cable from the selector housing. Refer to SHIFT LEVER AND HOUSING, FROM 11.06 .

-- Raise the upper spring leg -A- over the selector bracket tab.

-- Using a screwdriver, press the bearing shell notches -arrows- in the direction of the shift lever guide bearing; break the notches if necessary.

Fig 2: Identifying Bearing Shell Notches

Courtesy of VOLKSWAGEN UNITED STATES, INC.

-- Pry out the bearing shell -A- with the shift lever guide and remove the shift lever -B- from the shift housing.

-- Then, press the bearing shell off the shift lever guide and remove.

Fig 3: Identifying Bearing Shell Pressed Off Shift Lever Guide Bearing

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Observe the guides -A- in subsequent steps.
They must not break off.

-- Raise the lower leg -arrow 1- of the spring as far as the shoulder on the selector bracket.

-- Now, raise the shift lever guide up as far as the stop and remove ball studs from selector bracket -arrow 2-.

Fig 4: Identifying Guides -A- Observed In Subsequent Steps

Courtesy of VOLKSWAGEN UNITED STATES, INC.

-- Turn the shift lever in the -direction of arrow 1-.

Fig 5: Identifying Shift Lever Turned -Direction Of Arrow 1- To Place Pins In Shift Housing Opening

Courtesy of VOLKSWAGEN UNITED STATES, INC.

The pins -arrow 2- must be in the shift housing opening.

-- Move the shift lever guide and the shift lever in the -direction of arrow 3-.

Assembling

CAUTION:

The lower leg of the spring (-arrow 1 - in the upper illustration) can spring down uncontrolled from the selector bracket shoulder during subsequent handling.

-- Carefully press the spring leg down from the selector bracket shoulder.

The spring sides then twist "diagonally" with a loud noise.

-- Turn both springs to the right and release the tension on the legs -A and B-.

The legs -A and B- must face in the opposite direction.

Fig 6: Identifying Spring Side -A- Inserted From Above Into Guide & Pulled Down Near Guide To Position -B-
Courtesy of VOLKSWAGEN UNITED STATES, INC.

-- Insert the shift lever guide and the shift lever in the shift housing.

Fig 7: Identifying Pins Still Located In Shift Housing Opening

Courtesy of VOLKSWAGEN UNITED STATES, INC.

The pins -arrow 1- are still located in the shift housing opening.

-- Turn the shift lever guide in the -direction of arrow 2- until the ball head pin -A- is above the opening in the shift housing.

-- Install the shift housing with shift lever guide into the large depression -arrow- in the thrust block T10083.

Fig 8: Identifying Selector Housing With Shift Lever Guide Placed In Larger Depression On Pressing Support T10083

Courtesy of VOLKSWAGEN UNITED STATES, INC.

The shift lever guide must project out of the shift housing as far as the stop.

Fig 9: Identifying Spring Side -A- Inserted From Above Into Guide & Pulled Down Near Guide To Position -B-
Courtesy of VOLKSWAGEN UNITED STATES, INC.

-- Insert the spring leg -A- from above into the guide.

-- Pull the spring leg -B- down and insert it near the guide (in direction of ball head).

NOTE:

The selector bracket is only partially shown to provide a better illustration.

-- Carefully remove the shift housing with the shift lever guide from the thrust block T10083.

-- Move the selector bracket all the way to the rear (opposite mounting holes for shift and selector cable) -arrow 1-.

Fig 10: Identifying Selector Bracket Moved Back As Far As Stop & Ball Head Pins Pressed Into Selector Bracket

Courtesy of VOLKSWAGEN UNITED STATES, INC.

-- Lubricate the ball head pins.

-- Press the ball head pins into the selector bracket -arrow 2-.

The guides -A- and the tabs -B- must not be damaged.

-- Install the shift housing with shift lever guide into the large depression -arrow- in the thrust block T10083.

Fig 11: Identifying Selector Housing With Shift Lever Guide Placed In Larger Depression On Pressing Support T10083

Courtesy of VOLKSWAGEN UNITED STATES, INC.

The shift lever guide must project out of the selector housing as far as the stop.

Fig 12: Identifying New Bearing Shell -B- To Raise Upper Side Of Spring -A- Over Selector Bracket Pins
Courtesy of VOLKSWAGEN UNITED STATES, INC.

-- Raise the upper leg of the spring -A- over the selector bracket pins.

Use a new bearing shell -B-.

-- Lubricate bearing shells and the shift lever guide bearing.

-- Press the bearing shell onto the shift lever guide bearing as far as the stop.

-- Remove the shift mechanism from the thrust block T10083.

-- Press the bearing shell into the shift housing -arrows-.

All four retaining tabs must engage.

-- Insert the lower leg -C- of the spring into the guide.

-- Raise the upper leg of the spring -A- over the selector bracket tab into the guide.

-- Install the shift lever, shift cable, selector cable and base plate. Refer to SHIFT LEVER AND HOUSING, FROM 11.06 .

-- Install the shift mechanism. Refer to SHIFT MECHANISM .