Shift Cable And Selector Cable Overview: Notes

NOTE:

Lubricate the bearing areas and the sliding surfaces. Use the correct grease.

Fig 1: Identifying Shift And Selector Cables Overview

Gear Shift Shaft with Shift Cover
Sliding Shoe
Relay Lever
- Made of plastic.
- Installed position, refer to Fig 4.
- Remove and install together with the cable retainer -item 4- .
- To install, lubricate, refer to Fig 6.
- Adjust the shift mechanism after installing, refer to SHIFT MECHANISM, ADJUSTING .
- On the gear shift cover, removing and installing, refer to Fig 7.
Cable Retainer
- For attaching the selector cable to the relay lever.
- Adjust the shift mechanism after installing, refer to SHIFT MECHANISM, ADJUSTING .
- Do not interchange, the cable locking mechanisms for the selector cable to the relay lever and for the shift cable to the transmission shift lever are different.
- Removing from the selector cable, refer to Fig 5.
- Allocation, refer to Figure.
- Removing from the relay lever, refer to Figure.
- Pressing onto the relay lever, refer to Figure.
Transmission Shift Lever
- Insert so that the master spline aligns with the shift rod, refer to Fig 2.
- To install, lubricate, refer to Fig 3.
- Installed position, refer to Fig 4.
- Adjust the shift mechanism after installing, refer to SHIFT MECHANISM, ADJUSTING .
Nut
- 23 Nm
- Always replace after removing.
- Self locking.
Cable Retainer
- For attaching the shift cable to the transmission shift lever.
- Adjust the shift mechanism after installing, refer to SHIFT MECHANISM, ADJUSTING .
- Do not interchange, the cable locking mechanisms for the selector cable to the relay lever and for the shift cable to the transmission shift lever are different.
- Allocation, refer to Figure.
- Removing from the shift cable, refer to Fig 5.
Circlip
- Always replace after removing.
Circlip
- Always replace after removing.
- Be careful not to damage the cable when removing it.
Selector Cable
- Attach to the cable retainer -item 4- .
- Installed position, refer to SHIFT MECHANISM INSTALLED POSITION .
- Attach to the shift cable with a cable tie, refer to Figure.
- Removing and installing, refer to SHIFT CABLE AND SELECTOR CABLE .
Shift Housing
Circlip
- Always replace after removing.
- Be careful not to damage the cable when removing it.
Shift Cable
- Attach to the cable retainer -item 7- .
- Installed position, refer to SHIFT MECHANISM INSTALLED POSITION .
- Attach to the selector cable with a cable tie, refer to Figure.
- Removing and installing, refer to SHIFT CABLE AND SELECTOR CABLE .
Cable Bracket
- Made of plastic.
Bolt
- 20 Nm
- Quantity: 3
- For attaching the cable bracket -14- to the transmission.
Grommet
- For the cable bracket -14- to the transmission.
Spacer
Clip
- For the relay lever -3- .

Fig 2: Identifying Installation Of Transmission Shift Lever

-- When positioning the transmission shift lever, make sure the gap -arrow A- is placed over the missing selector shaft teeth -arrow B- .

Fig 3: Identifying Transmission Shift Lever Guide Rail Lubrication Area

Lubricate the transmission shift lever guide rail -B- , into which the relay lever engage, especially carefully.
Use the correct grease allocation.

NOTE:

The illustration of the transmission shift lever may differ from the original part.

Fig 4: Selector Lever/Selector Relay Lever Installed Position

1 - Transmission shift lever

2 - The relay lever fits into the guide rail on the transmission shift lever via the sliding shoe -arrow- .

Fig 5: Identifying Sequence To Release Retainers -A- For Shift And Selector Cables -B-

-- Pull the locking mechanism all the way forward in the -direction of arrow 1- and lock it in the -direction of arrow 2- .

-- Remove the cable -B- from the cable retainer -A- .

Fig 6: Identifying Relay Lever Shaft Lubrication Area

Lubricate the shaft -A- on the relay lever carefully -arrows- with 0.2 g of grease.
Use the correct grease allocation.

Fig 7: Removing And Securing Selector Relay Lever To Gearshift Lever