Overview - Control Module And Hydraulic Unit
WARNING: This page is about a different car, the 2015 Volkswagen Passat, 2014 Volkswagen Passat, 2013 Volkswagen Passat, and 2012 Volkswagen Passat. However, it is still accessible from the selected car via links, so may be relevant.
- ABS Hydraulic Unit -N55-
- Removing and installing 4 Cylinder Gasoline Engine. Refer to ABS Control Module -J104- /ABS Hydraulic Unit -N55-
- Removing and installing 5 Cylinder Gasoline Engine. Refer to ABS Control Module -J104- AND ABS Hydraulic Unit -N55-
- Removing and installing 6 Cylinder Gasoline Engine. Refer to ABS Control Module -J104- AND ABS Hydraulic Unit -N55-
- Removing and installing 4 Cylinder Diesel Engine. Refer to ABS Control Module -J104- AND ABS Hydraulic Unit -N55-
- Disconnect the ABS Hydraulic Unit -N55- from the ABS Control Module -J104-. Refer to ABS CONTROL MODULE, SEPARATING FROM ABS HYDRAULIC UNIT .
- ABS Control Module -J104-
- Removing and installing 4 Cylinder Gasoline Engine. Refer to ABS Control Module -J104- /ABS Hydraulic Unit -N55-
- Removing and installing 5 Cylinder Gasoline Engine. Refer to ABS Control Module -J104- AND ABS Hydraulic Unit -N55-
- Removing and installing 6 Cylinder Gasoline Engine. Refer to ABS Control Module -J104- AND ABS Hydraulic Unit -N55-
- Removing and installing 4 Cylinder Diesel Engine. Refer to ABS Control Module -J104- AND ABS Hydraulic Unit -N55-
- Disconnect the ABS Control Module -J104- from the ABS Hydraulic Unit -N55-, refer to ABS CONTROL MODULE, SEPARATING FROM ABS HYDRAULIC UNIT
- Bolt
- 2 Nm ± 0.8 Nm
- Quantity: 4
- Always replace if removed.
- Brake Line
- 14 Nm
- To left front brake caliper.
- Identification: Diameter 5.25 mm and tube fitting with M10 x 1 thread.
- Brake Line
- 14 Nm
- ABS Hydraulic Unit -N55- for the master brake cylinder/primary piston circuit.
- Identification: 6.5 mm and tube fitting with M12 x 1 thread.
- Brake Line
- 14 Nm
- To right front brake caliper.
- Identification: 5.25 mm and tube fitting with M12 x 1 thread.
- Brake Line
- 14 Nm
- ABS Hydraulic Unit -N55- for the master brake cylinder/secondary piston circuit.
- Identification: 6.5 mm and tube fitting with M12 x 1 thread.
- Brake Line
- 14 Nm
- Master brake cylinder/primary piston circuit for the ABS Hydraulic Unit -N55-.
- Identification: 6.5 mm and tube fitting with M12 x 1 thread
- Brake Line
- 14 Nm
- Master brake cylinder/secondary piston circuit for the ABS Hydraulic Unit -N55-.
- Identification: 6.5 mm and tube fitting with M12 x 1 thread
- Brake Booster
- Overview, refer to BRAKE BOOSTER AND MASTER BRAKE CYLINDER OVERVIEW .
- Removing and installing, with 5-cylinder gasoline engine, refer to BRAKE BOOSTER .
- Removing and installing, with 6-cylinder gasoline engine, refer to BRAKE BOOSTER .
- Removing and installing, with a 4-cylinder diesel engine, refer to BRAKE BOOSTER .
- Brake Line
- 14 Nm
- To left rear brake caliper/brake cylinder.
- Identification: Diameter 5.25 mm and tube fitting with M12 x 1 thread.
- Brake Line
- 14 Nm
- To the right rear brake caliper/brake cylinder.
- Identification: Diameter 5.25 mm and tube fitting with M10 x 1 thread.
- Hex Bolt
- 8 Nm
- Rubber Insulation
- Bracket
- After installing, make sure it fits properly.
- Bolt
- 8 Nm
- Quantity: 3
- Nut
- 8 Nm
- Quantity: 2
- Bracket
- Rubber Insulation
- Do not press the rubber bushings out of the bracket when installing the mount.