LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Volkswagen >> 2010 >> Touareg Base >> Repair and Diagnosis >> Suspension >> Wheel Alignment >> Wheels, Tires And Vehicle Alignment >> 44 Wheels, Tires And Vehicle Alignment >> General Information >> Adaptive Cruise Control, Calibration Without Prior Vehicle Alignment >> Notes
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Adaptive Cruise Control, Calibration Without Prior Vehicle Alignment: Notes

Observe The Following Work Sequence!

-- Observe the notes in your alignment unit and specifications in general information ADAPTIVE CRUISE CONTROL, CALIBRATION INFORMATION 

Fig 1: Attention
GWWN01-0453Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

Measuring Procedure

                         
  Start → Is there enough room in front of the vehicle Fig 2 → No  
            ↓       ↓    
          Yes   Drive vehicle backwards onto alignment stand  
            ↓       ↓    
  Read the measured values block using Vehicle diagnostic tester ← Perform wheel run-out compensation. ← ← ←    
    ↓                    
  Select in Vehicle diagnostic tester: Selection on the Vehicle Diagnosis Tester:  → The dialog follows in the Vehicle diagnostic tester → Send the values for the measuring point from Vehicle diagnostic tester to the measuring field on VAS 6041/2 or 6430/2Fig 5  
                    ↓    
  Note dimension -a- Fig 2 ← Position ACC adjustment deviceVAS 6041 and 6430 in front of the vehicle ← Remove VW emblem from radiator grille Fig 3  
    ↓                    
  Level ACC adjustment deviceVAS 6041 and 6430 and adjust the straight drive → Follow the instructions in the Vehicle diagnostic tester → Select in Vehicle diagnostic tester: Selection on the Vehicle Diagnosis Tester:   
                    ↓    
          Automatic Cruise Control (ACC) sensor -G550- adjusting screw identification Fig 4 ← The dialog follows in the Vehicle diagnostic tester  
            ↓            
          End          
                         
Fig 2: Identifying Distance Between Automatic Cruise Control Sensor Mirror And ACC Adjustment Tool VAS Measuring Field
GWWN44-10305Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-a- = 1145 mm

Distance -a- is distance between Automatic Cruise Control (ACC) sensor -G550- mirror and ACC adjustment toolVAS 6041 and VAS 6430 measuring field

NOTE:

If necessary, use the precision spoiler adapterV.A.G 1813/12 to equalize the height between the ACC adjustment toolVAS 6041 and 6430 and the vehicle alignment platform.

Fig 3: Identifying Removal Of VW Emblem With Screwdriver
GWWN44-10256Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

-- Guide a screw driver through opening -arrow A- and press tab -arrow B- downward.

-- Remove VW emblem.

Fig 4: Adaptive Cruise Control Sensor G550 Identification Of Adjusting Screws
GWWN44-10255Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.
  1. Horizontal or measuring block 6-2 adjusting screw Fig 4
  2. Vertical or measuring block 6-3 adjusting screw Fig 4
  3. Must not be turned - functions only as a pivot point
Fig 5: Explanation Of Axles And Display In VAS 505X
GWWN44-10306Courtesy of VOLKSWAGEN GROUP OF AMERICA, INC.

Y -

Measuring block 6-2

X -

Measuring block 6-3

Example:

Value 0.1 corresponds to 4 mm on VAS 6041/2 and/or 6430/2

The display on Vehicle diagnostic tester show a value of 0.6 in measured values block 6-2 and a value of -1.0 in measured values block 6-3.

These values lead to a measuring point -arrow- that consists of the following values:

-a- = 24 mm

-b- = 40 mm

scientia non olet · About LEMON Manuals