Update Programming To Eliminate DTC P150A Stored In ECM Fault Memory (V011006)

Publication date: 2013-08-14
Reference number: V011006
Supersedes refnos: 2022598, GROUP 01, NO. 10-06, GROUP 01, NO. 13-29

UPDATE PROGRAMMING TO ELIMINATE DTC P150A STORED IN ECM FAULT MEMORY

TECHNICAL SERVICE BULLETIN

Reference Number(s): GROUP 01, NO. 13-29 (2022598), Date of Issue: August 14, 2013

VOLKSWAGEN:	2009 Rabbit, Jetta, Jetta Wagon
GROUP:	01 - On-Board Diagnostic

Superceded Bulletin(s): GROUP 01, NO. 10-06, Date of Issue: April 1, 2010

APPLICABLE MODELS AND YEARS

Model(s)	Year	Engine Code	Trans. Code	VIN Range From	VIN Range To
Rabbit, Jetta, Jetta Wagon	2009	2.5L CBTA/CBUA	All	All	All

CONDITION

01 13 29 August 14, 2013 2022598 Supersedes Technical Bulletin V011006 dated April 1, 2010 due to updated SVM Action Code.

Update Programming to Eliminate DTC P150A Stored in ECM Fault Memory

This Technical Bulletin addresses the following Diagnostic Trouble Code (DTC) on 2009 Jetta/Jetta Wagon 2.5L and Rabbit 2.5L vehicles equipped with the ME17.5 engine management system with a MAP-sensor.

DIAGNOSTIC TROUBLE CODES

DTC	Description
P150A	Engine Off Timer Performance

TECHNICAL BACKGROUND

Customers may complain of a MIL ON condition, which is caused by DTC P150A.

The condition as described does not affect vehicle performance or operation.

PRODUCTION SOLUTION

Improved software was introduced in production.

SERVICE

Update Programming Procedure

Tip:

To Update-Programming using SVM, review and follow instructions in Technical Bulletin Instance 2014603 "Software Version Management".

The SVM Process must be completed in its entirety so the database receives the update confirmation response. A warranty claim may not be reimbursed if there is no confirmation response to support the claim.

Ensure attached ECM/TCM Tuning Form has been completed and signed by customer as required in SVM Technical Bulletin Instance 2014603 .

NOTE: Prior to launching the VAS-PC and ODIS service diagnostic applications and starting control module update process, confirm tester screen saver and power settings in accordance with Special Tools and Equipment - Service Information Circular # VVT-12-02. Failure to do so may result in the tester entering power save mode during data transfer, and subsequent control module failure.

When using a VAS 6150/5051B or VAS 5052A tester in conjunction with a VAS 5054A wireless transmitter head for a flash procedure, please connect a USB cable between the transmitter head and the tester. Failure to do so may lead to errors during the flash procedure.

VAS tools must only be used with their power adapters plugged in. Under no circumstances should they be used on battery power alone during the programming procedure.

Critical Warning: The Midtronics Battery Charger must be connected to the vehicle battery for the duration of the programming, to ensure the battery state of charge remains above 12.5 volts during the update process. If the battery drops below 12.5 volts, the programming could fail which may result in damage to the control module. Control modules damaged by inadequate voltage will not be covered under the warranty policy. The technician should verify the vehicle voltage prior to starting the update process, and should monitor the voltage for the duration of the update.

Update the Engine Control Module using the SVM action code as listed in the table below:

SOFTWARE VERSION MANAGEMENT

Model	Engine	Old Software Part No.	Old Software Version	New Software Part No. New	Software Version (or higher)	SVM Action Code
Jetta, Jetta Wagon, Rabbit	2.5L CBTA/CBUA	07K 906 055 Q	All	07K 906 055 Q	3862	3565
		07K 906 055 P	All	07K 906 055 P	3861	3565
		07K 906 055 N	All	07K 906 055 N	3860	3565
		07K 906 055 M	All	07K 906 055 M	3859	3565

The procedure can be found in GFF under Functions/Component Selection, Software Version Management, Adjust Software.

Tip:

Upon completion of software update, verify Cruise Control function (if originally equipped) is activated via GFF Function Test Plan 01 - Activate/Deactivate Cruise Control System.

WARNING: Radiator Fan(s) may cycle ON high speed during the Update Process! There is a risk that personal injury may result if contact is made with spinning fan blades.
Keep hands and all objects away from Radiator Fan(s) during Update Process!

Tip:

Ensure attached ECM/TCM Tuning Form has been completed and signed by customer as required in SVM Technical Bulletin Instance 2014603 .

WARRANTY

WARRANTY INFORMATION

To determine if this procedure is covered under Warranty, always refer to the Warranty Policies and Procedures Manual ⁽¹⁾

Model(s)

Year(s)

Eng. Code(s)

Trans. Code(s)

VIN Range From

VIN Range To

Rabbit, Jetta, Jetta Wagon

2009

2.5L CBTA/CBUA

All

SAGA Coding

Claim Type:

Use applicable Claim Type ⁽¹⁾

Service Number:

Damage Code

HST

Damage Location (Depends on Service No.)

2470

0039

Use applicable when indicated in ElsaWeb (L/R)

Parts Manufacturer

Rabbit

WWO ⁽²⁾

Jetta

3ME ⁽²⁾

Labor Operation ⁽³⁾ :

24702599 = 35 TU

Labor Operation ⁽³⁾ : Charge Battery

27068950 = 10 TU

Causal Part : Select Labor Operation

24702599

Diagnostic Time ⁽⁴⁾

GFF Time expenditure

01500000 = 00 TU max.

YES

Road Test

01210002 = 00 TU
01210004 = 00 TU

Technical Diagnosis

01320000 = 00 TU max.

Claim Comment: Input "As per Technical Bulletin 2022598" in comment section of Warranty Claim.

⁽¹⁾	Vehicle may be outside any Warranty in which case this Technical Bulletin is informational only

⁽²⁾	Code per warranty vendor code policy.

⁽³⁾	Labor Time Units (TUs) are subject to change with ELSA updates.

⁽⁴⁾	Documentation required per Warranty Policies and Procedures Manual.

REQUIRED PARTS AND TOOLS

No Special Parts required.

TOOL INFORMATION

Tool Description	Tool No:
Midtronics Battery Tester/Charger	InCharge 940 (INC-940)
VAS Diagnostic Tool	VAS 5051B, VAS 5052A, VAS 6150/X & VAS 6160/-VPC with: VAS-PC Base V19.01.01 and current version Brand disc ODIS Service V1.1.3 or higher

ADDITIONAL INFORMATION

All part and service references provided in this Technical Bulletin are subject to change and/or removal. Always check with your Parts Dept. and Repair Manuals for the latest information.

ATTACHMENT