Communication Interruptions Following Door Control Module Replacement (GROUP 64, NO. 14-01)

WARNING: This page is about the Jetta 2.0T, Automatic DCT, which is a different variant/trim than selected.

Publication date: 2014-03-10
Reference number: GROUP 64, NO. 14-01
Supersedes refnos: 2035718, GROUP 57, NO. 13-01

COMMUNICATION INTERRUPTIONS FOLLOWING DOOR CONTROL MODULE REPLACEMENT

TECHNICAL SERVICE BULLETIN

Reference Number(s): GROUP 64, NO. 14-01 (2035718), Date of Issue: March 10, 2014

VOLKSWAGEN:	2005.5-2009 Jetta; 2008-2009 Jetta Wagon
GROUP:

Superceded Bulletin(s): GROUP 57, NO. 13-01, Date of Issue: November 11, 2013

APPLICABLE MODELS AND YEARS

Model(s)	Year	Engine Code	Trans. Code	VIN Range From	VIN Range To
Jetta	2005.5-2009	All	All	All	All
Jetta Wagon	2008-2009	All	All	All	All

CONDITION

64 14 01 March 10, 2014 2035718 Supersedes Technical Bulletin 57-13-01 dated November 11, 2013 to update information, including repair group confusion.

Communication Interruptions Following Door Control Module Replacement

After replacement of the front door control modules, the gateway control module may not communicate with the newly installed door control module.

TECHNICAL BACKGROUND

Tip: Please also see parts bulletin 9-130 in ETKA under Infoline > Technology > GP Bulletins > (9-130) Procedure for communication interruptions following door control unit renewal during repair

Due to further technical development and releases, the latest generation door control units which are UDS diagnosis compatible are now available as service parts for the A5 Jetta and Jetta Wagon, replacing the previously installed KWP 2000 units. In individual cases, there may be communication problems with the newly installed door control unit during diagnosis and connection (coding, adaption, etc).

PRODUCTION SOLUTION

Vehicles no longer in production at time of publication.

SERVICE

Please check whether a corresponding KWP/UDS-compatible diagnosis interface (gateway) has already been installed in the vehicle. Older diagnosis interfaces (gateways) are only compatible with the KWP 2000 diagnosis. In order to ensure fault-free diagnosis and communication, it may be necessary to replace the diagnosis interface (gateway) with a KWP/UDS-compatible diagnosis interface (gateway). These can be found in ETKA.

Due to a hardware / software change between the KWP 2000 and UDS door control modules, the opposite door control module may also require replacement (e.g. if replacing the driver's side door control module, the passenger side door control module may also need to be replaced, along with the possibility of needing to replace the Gateway). Replacement parts are listed per VIN in ETKA.

Control Module Coding:

NOTE: In some cases ODIS may not be able to identify the updated UDS models. If this occurs, manually identifying the vehicle as a 2010 Jetta Sedan should resolve the concern.
The door control modules will need to be long coded. In order to code the module you will need to start with the original coding for the door control module (found in GFF paperless if unable to read module). Using a programming calculator found in windows or on-line, select "programming" mode. Ensure "DEC" is selected. Enter the original coding and select "HEX" (example: 1205 > 4B5). It may be necessary to add "0's" to the front of the HEX code to complete the coding (example 00 04 B5).
Code the gateway control module using ODIS. Right click on address word 19 Gateway > select Control Module OBD > select Code Bus Master > select Perform. In the "Gateway List" you will see modules with a "?", select all of the modules and select "apply" in the lower right corner of the screen. Clear any stored DTCs and check operation.

WARRANTY

Information only.

REQUIRED PARTS AND TOOLS

No Special Parts required.

TOOL INFORMATION

Tool Description	Tool No:
Midtronics Battery Tester/Charger	InCharge 940 (INC-940)
VAS Diagnostic Tool	VAS 5051B, VAS 5052A, VAS 6150/X & VAS 6160/X with: ODIS Service 2.0.0 or higher with current online updates

ADDITIONAL INFORMATION

All part and service references provided in this Technical Bulletin are subject to change and/or removal. Always check with your Parts Dept. and Repair Manuals for the latest information.