LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Volkswagen >> 2007 >> Eos 3.2 >> Repair and Diagnosis >> Engine Performance >> Ignition System >> 3.2L - Generic Scan Tool - Engine Code(S): Bub >> St Generic Scan Tool >> Diagnostic Trouble Code Tables >> Sae P0XXX Diagnostic Trouble Codes >> Ignition system
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Ignition system

DTC Error Message Diagnostic Procedure Malfunction Criteria and Threshold Value Secondary Parameters with Enable Conditions Monitoring Time Length Frequency of checks, MIL Illumination
P0300 Random Misfire Detected -- Check the fuel injectors -N30, N31, N32, N33, N83, N84-. Refer to FUEL INJECTORS N30, N31, N32, AND N33, CHECKING .
-- Check the Ignition Coil with Power Output Stage --. Refer to IGNITION COILS WITH POWER OUTPUT STAGE, CHECKING .
-- Check the Spark plugs. Refer to SPARK PLUGS, TEST DATA
  • Check the intake system for leaks.
  • Check fuel pressure
  • Emission threshold misfire rate (MR) >2.8%
  • Catalyst damage misfire rate (MR), > 1.2-15%
  • Time after engine start, idle-150 RPM
  • Camshaft revolutions, 1
  • Engine speed range, idle-6600 RPM
  • Engine torque, > 0 torque (Nm)
  • IAT, >-48°C
  • Fuel cut off, Not active
  • ECT at start, >- 30°C
  • Rough road, Not detected
  • Internal CAN, No fault
  • 1000 Rev.
  • 200 Rev.
  • Continuous
  • 2 DCY
  • Immed.
P0301 Cylinder 1 Misfire Detected -- Check the fuel injectors -N30, N31, N32, N33, N83, N84-. Refer to FUEL INJECTORS N30, N31, N32, AND N33, CHECKING .
-- Check the Ignition Coil with Power Output Stage --. Refer to IGNITION COILS WITH POWER OUTPUT STAGE, CHECKING .
-- Check the Spark plugs. Refer to SPARK PLUGS, TEST DATA
  • Check the intake system for leaks.
  • Check fuel pressure
  • Emission threshold misfire rate (MR) >2.8%
  • Catalyst damage misfire rate (MR), > 1.2-15%
  • Time after engine start, idle-150 RPM
  • Camshaft revolutions, 1
  • Engine speed range, idle-6600 RPM
  • Engine torque, > 0 torque (Nm)
  • IAT, >-48 °C
  • Fuel cut off, Not active
  • ECT at start, >- 30°C
  • Rough road, Not detected
  • Internal CAN, No fault
  • 1000 Rev.
  • 200 Rev.
  • Continuous
  • 2 DCY
  • Immed.
P0302 Cylinder 2 Misfire Detected -- Check the fuel injectors -N30, N31, N32, N33, N83, N84-. Refer to FUEL INJECTORS N30, N31, N32, AND N33, CHECKING .
-- Check the Ignition Coil with Power Output Stage --. Refer to IGNITION COILS WITH POWER OUTPUT STAGE, CHECKING .
-- Check the Spark plugs. Refer to SPARK PLUGS, TEST DATA
  • Check the intake system for leaks.
  • Check fuel pressure
  • Emission threshold misfire rate (MR) >2.8%
  • Catalyst damage misfire rate (MR), > 1.2-15%
  • Time after engine start, idle-150 RPM
  • Camshaft revolutions, 1
  • Engine speed range, idle-6600 RPM
  • Engine torque, > 0 torque (Nm)
  • IAT, >-48°C
  • Fuel cut off, Not active
  • ECT at start, >- 30°C
  • Rough road, Not detected
  • Internal CAN, No fault
  • 1000 Rev.
  • 200 Rev.
  • Continuous
  • 2 DCY
  • Immed.
P0303 Cylinder 3 Misfire Detected -- Check the fuel injectors -N30, N31, N32, N33, N83, N84-. Refer to FUEL INJECTORS N30, N31, N32, AND N33, CHECKING .
-- Check the Ignition Coil with Power Output Stage --. Refer to IGNITION COILS WITH POWER OUTPUT STAGE, CHECKING .
-- Check the Spark plugs. Refer to SPARK PLUGS, TEST DATA
  • Check the intake system for leaks.
  • Check fuel pressure
  • Emission threshold misfire rate (MR) >2.8%
  • Catalyst damage misfire rate (MR), > 1.2-15%
  • Time after engine start, idle-150 RPM
  • Camshaft revolutions, 1
  • Engine speed range, idle-6600 RPM
  • Engine torque, > 0 torque (Nm)
  • IAT, >-48°C
  • Fuel cut off, Not active
  • ECT at start, >- 30°C
  • Rough road, Not detected
  • Internal CAN, No fault
  • 1000 Rev.
  • 200 Rev.
  • Continuous
  • 2 DCY
  • Immed.
P0304 Cylinder 4 Misfire Detected -- Check the fuel injectors -N30, N31, N32, N33, N83, N84-. Refer to FUEL INJECTORS N30, N31, N32, AND N33, CHECKING .
-- Check the Ignition Coil with Power Output Stage --. Refer to IGNITION COILS WITH POWER OUTPUT STAGE, CHECKING .
-- Check the Spark plugs. Refer to SPARK PLUGS, TEST DATA
  • Check the intake system for leaks.
  • Check fuel pressure
  • Emission threshold misfire rate (MR) >2.8%
  • Catalyst damage misfire rate (MR), > 1.2-15%
  • Time after engine start, idle-150 RPM
  • Camshaft revolutions, 1
  • Engine speed range, idle-6600 RPM
  • Engine torque, > 0 torque (Nm)
  • IAT, >-48°C
  • Fuel cut off, Not active
  • ECT at start, >- 30°C
  • Rough road, Not detected
  • Internal CAN, No fault
  • 1000 Rev.
  • 200 Rev.
  • Continuous
  • 2 DCY
  • Immed.
P0305 Cylinder 5 Misfire Detected -- Check the fuel injectors -N30, N31, N32, N33, N83, N84-. Refer to FUEL INJECTORS N30, N31, N32, AND N33, CHECKING .
-- Check the Ignition Coil with Power Output Stage --. Refer to IGNITION COILS WITH POWER OUTPUT STAGE, CHECKING .
-- Check the Spark plugs. Refer to SPARK PLUGS, TEST DATA
  • Check the intake system for leaks.
  • Check fuel pressure
  • Emission threshold misfire rate (MR) >2.8%
  • Catalyst damage misfire rate (MR), > 1.2-15%
  • Time after engine start, idle-150 RPM
  • Camshaft revolutions, 1
  • Engine speed range, idle-6600 RPM
  • Engine torque, > 0 torque (Nm)
  • IAT, >-48°C
  • Fuel cut off, Not active
  • ECT at start, >- 30°C
  • Rough road, Not detected
  • Internal CAN, No fault
  • 1000 Rev.
  • 200 Rev.
  • Continuous
  • 2 DCY
  • Immed.
P0306 Cylinder 6 Misfire Detected -- Check the fuel injectors -N30, N31, N32, N33, N83, N84-. Refer to FUEL INJECTORS N30, N31, N32, AND N33, CHECKING .
-- Check the Ignition Coil with Power Output Stage --. Refer to IGNITION COILS WITH POWER OUTPUT STAGE, CHECKING .
-- Check the Spark plugs. Refer to SPARK PLUGS, TEST DATA
  • Check the intake system for leaks.
  • Check fuel pressure
  • Emission threshold misfire rate (MR) >2.8%
  • Catalyst damage misfire rate (MR), > 1.2-15%
  • Time after engine start, idle-150 RPM
  • Camshaft revolutions, 1
  • Engine speed range, idle-6600 RPM
  • Engine torque, > 0 torque (Nm)
  • IAT, >-48°C
  • Fuel cut off, Not active
  • ECT at start, >- 30°C
  • Rough road, Not detected
  • Internal CAN, No fault
  • 1000 Rev.
  • 200 Rev.
  • Continuous
  • 2 DCY
  • Immed.
P0321 Ignition/Distributor Engine Speed Input Circuit Range/Performance -- Check the Engine Speed (RPM) Sensor -G28-. Refer to ENGINE SPEED SENSOR G28, CHECKING .
  • Missing ref mark within 720°KW >2 in a row
  • And Engine speed signal
  • Missing ref mark >5 anytime
  • And Within >8 in a row
  • Signal correction +/- 1 tooth >8 in a row
  • And Engine speed no signal
 - 0.5 Seconds
  • Multiple
  • 2 DCY
P0322 Ignition/Distributor Engine Speed Input Circuit No Signal -- Check the Engine Speed (RPM) Sensor -G28-. Refer to ENGINE SPEED SENSOR G28, CHECKING .
  • Camshaft signals >8
 - 0.5 Seconds
  • Multiple
  • 2 DCY
P0324 Knock Control System Error -- Check the Knock Sensors --. Refer to KNOCK SENSOR, CHECKING .
  • Zero test procedure, failed
  • Test impulse zero-test procedure failed
  • ECT, > 39°C
  • Engine speed, 640-6400 RPM
  • Engine load, >30%
  • Knock control, Active
 150 Seconds 60 Seconds
  • Multiple
  • 2 DCY
P0327 Knock Sensor 1 Circuit Low Input (Bank 1) -- Check the Knock Sensors --. Refer to KNOCK SENSOR, CHECKING . Lower threshold, 0.43-4.18 V
  • Engine speed, > 1960 RPM
  • ECT, > 39°C
  • Engine load, > 30%
 0.5 Seconds
  • Continuous
  • 2 DCY
P0328 Knock Sensor 1 Circuit High Input (Bank 1) -- Check the Knock Sensors --. Refer to KNOCK SENSOR, CHECKING . Upper threshold, 16.29-114.75 V
  • Engine speed, > 1960 RPM
  • ECT, > 39°C
  • Engine load, > 30%
 0.5 Seconds
  • Continuous
  • 2 DCY
P0332 Knock Sensor 2 Circuit Low Input (Bank 2) -- Check the Knock Sensors --. Refer to KNOCK SENSOR, CHECKING . Lower threshold, 0.43-4.18 V
  • Engine speed, > 1960 RPM
  • ECT, > 39°C
  • Engine load, > 30%
 0.5 Seconds
  • Continuous
  • 2 DCY
P0333 Knock Sensor 2 Circuit High Input (Bank 2) -- Check the Knock Sensors --. Refer to KNOCK SENSOR, CHECKING . Upper threshold, 16.29-114.75 V
  • Engine speed, > 1960 RPM
  • ECT, > 39°C
  • Engine load, > 30%
 0.5 Seconds
  • Continuous
  • 2 DCY
P0341 Camshaft Position Sensor A Circuit Range/Performance (Bank 1 or single sensor) -- Check the Camshaft Position (CMP) Sensor -G40-. Refer to CAMSHAFT POSITION SENSORS G40 AND G163, CHECKING . Signal voltage, no altering at reference gap - 0.5 Seconds
  • Continuous
  • 2 DCY
P0342 Camshaft Position Sensor A Circuit Low Input (Bank 1 or single sensor) -- Check the Camshaft Position (CMP) Sensor -G40-. Refer to CAMSHAFT POSITION SENSORS G40 AND G163, CHECKING . Signal low voltage, 12 Rev. - 0.5 Seconds
  • Continuous
  • 2 DCY
P0343 Camshaft Position Sensor A Circuit High Input (Bank 1 or single sensor) -- Check the Camshaft Position (CMP) Sensor -G40-. Refer to CAMSHAFT POSITION SENSORS G40 AND G163, CHECKING . Signal voltage high, 12 rev. - 0.5 Seconds
  • Continuous
  • 2 DCY
P0351 Ignition Coil A Primary/Secondary Circuit -- Check the Ignition Coil with Power Output Stage --. Refer to IGNITION COILS WITH POWER OUTPUT STAGE, CHECKING .
  • Open circuit signal voltage 5.2-6.0 V
  • Short to ground signal voltage 0.5-1.0 V
  • Short to B + signal current, < 5-8.8 mA
 Engine speed, >80 RPM 0.5 Seconds
  • Continuous
  • 2 DCY
P0352 Ignition Coil B Primary/Secondary Circuit -- Check the Ignition Coil with Power Output Stage --. Refer to IGNITION COILS WITH POWER OUTPUT STAGE, CHECKING .
  • Open circuit signal voltage 5.2-6.0 V
  • Short to ground signal voltage 0.5-1.0 V
  • Short to B + signal current, < 5-8.8 mA
 Engine speed, >80 RPM 0.5 Seconds
  • Continuous
  • 2 DCY
P0353 Ignition Coil C Primary/Secondary Circuit -- Check the Ignition Coil with Power Output Stage --. Refer to IGNITION COILS WITH POWER OUTPUT STAGE, CHECKING .
  • Open circuit signal voltage 5.2-6.0 V
  • Short to ground signal voltage 0.5-1.0 V
  • Short to B + signal current, < 5-8.8 mA
 Engine speed, >80 RPM 0.5 Seconds
  • Continuous
  • 2 DCY
P0354 Ignition Coil D Primary/Secondary Circuit -- Check the Ignition Coil with Power Output Stage --. Refer to IGNITION COILS WITH POWER OUTPUT STAGE, CHECKING .
  • Open circuit signal voltage 5.2-6.0 V
  • Short to ground signal voltage 0.5-1.0 V
  • Short to B + signal current, < 5-8.8 mA
 Engine speed, >80 RPM 0.5 Seconds
  • Continuous
  • 2 DCY
P0355 Ignition Coil "E" Primary/Secondary Circuit -- Check the Ignition Coil with Power Output Stage --. Refer to IGNITION COILS WITH POWER OUTPUT STAGE, CHECKING .
  • Open circuit signal voltage 5.2-6.0 V
  • Short to ground signal voltage 0.5-1.0 V
  • Short to B + signal current, < 5-8.8 mA
 Engine speed, >80 RPM 0.5 Seconds
  • Continuous
  • 2 DCY
P0356 Ignition Coil "F" Primary/Secondary Circuit -- Check the Ignition Coil with Power Output Stage --. Refer to IGNITION COILS WITH POWER OUTPUT STAGE, CHECKING .
  • Open circuit signal voltage 5.2-6.0 V
  • Short to ground signal voltage 0.5-1.0 V
  • Short to B + signal current, < 5-8.8 mA
 Engine speed, >80 RPM 0.5 Seconds
  • Continuous
  • 2 DCY
P0366 Camshaft Position Sensor "B" Circuit Range/Performance Bank 1 -- Check the Camshaft Position (CMP) Sensor -G40-. Refer to CAMSHAFT POSITION SENSORS G40 AND G163, CHECKING . Signal voltage, no altering at reference gap - 0.5 Seconds
  • Continuous
  • 2 DCY
P0367 Camshaft Position Sensor "B" Circuit Low Bank 1 -- Check the Camshaft Position (CMP) Sensor -G40-. Refer to CAMSHAFT POSITION SENSORS G40 AND G163, CHECKING . Signal low voltage, 12 Rev. - 0.5 Seconds
  • Continuous
  • 2 DCY
P0368 Camshaft Position Sensor "B" Circuit High Bank 1 -- Check the Camshaft Position (CMP) Sensor -G40-. Refer to CAMSHAFT POSITION SENSORS G40 AND G163, CHECKING . Signal voltage high, 12 rev. - 0.5 Seconds
  • Continuous
  • 2 DCY
scientia non olet · About LEMON Manuals