LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Volkswagen >> 2007 >> Eos 2.0T, Automatic DCT >> Repair and Diagnosis >> Engine Performance >> System >> 2.0L - Generic Scan Tool - Engine Code(S): BPY >> St Generic Scan Tool >> Diagnostic Trouble Code Tables >> Sae P0XXX Diagnostic Trouble Codes >> Ignition system
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Ignition system

DTC Error Message Diagnostic Procedure Malfunction Criteria and Threshold Value Secondary Parameters with Enable Conditions Monitoring Time Length Frequency of checks, MIL Illum
P0300 Random Misfire Detected -- Check the Spark plugs.-- Check the intake system for leaks.-- Check the fuel pressure. Refer to FUEL PRESSURE, CHECKING .-- Check fuel injectors -N30, N31, N32, N33, -.-- Check the Ignition Coils with Power Output Stage -N70, N127, N291, N292-. Refer to IGNITION COILS WITH POWER OUTPUT STAGE, CHECKING .
  • Emission threshold 1st interval %(MR), >1.7% >1.4%
  • Emission threshold misfire rate (MR), > 1.7% >1.4%
  • Catalyst damage misfire rate (MR) >1.6-20%>400 |20-160>2.5-20%
  • Time from start, 0 Sec.
  • IAT, >-48° C
  • Time after engine start, Idle - 150 RPM
  • Engine torque, >5.47-23.4%
  • Camshaft revolutions 1
  • Engine speed range, 480-6800 RPM
  • Fuel cutoff, Not active
  • ECT at start, > -9° C
  • If ECT at start <-99° C wait until actual ECT >18° C
  • 1000 Rev.
  • 200 Rev.
  • 2 DCY
  • Immed.
P0301  Cylinder 1 Misfire Detected -- Check the Spark plugs.-- Check the intake system for leaks.-- Check the fuel pressure. Refer to FUEL PRESSURE, CHECKING .-- Check fuel injectors -N30, N31, N32, N33, -.-- Check the Ignition Coils with Power Output Stage -N70, N127, N291, N292-. Refer to IGNITION COILS WITH POWER OUTPUT STAGE, CHECKING .
  • Emission threshold 1st interval %(MR), >1.7% >1.4%
  • Emission threshold misfire rate (MR), > 1.7% >1.4%
  • Catalyst damage misfire rate (MR) >1.6-20%>400 |20-160>2.5-20%
  • Time from start, 0 Sec.
  • IAT, >-48° C
  • Time after engine start, Idle - 150 RPM
  • Engine torque, >5.47-23.4%
  • Camshaft revolutions 1
  • Engine speed range, 480-6800 RPM
  • Fuel cutoff, Not active
  • ECT at start, > -9° C
  • If ECT at start <-99° C wait until actual ECT >18° C
  • 1000 Rev.
  • 200 Rev.
  • 2 DCY
  • Immed.
P0302  Cylinder 2 Misfire Detected -- Check the Spark plugs.-- Check the intake system for leaks.-- Check the fuel pressure. Refer to FUEL PRESSURE, CHECKING .-- Check fuel injectors -N30, N31, N32, N33, -.-- Check the Ignition Coils with Power Output Stage -N70, N127, N291, N292-. Refer to IGNITION COILS WITH POWER OUTPUT STAGE, CHECKING .
  • Emission threshold 1st interval %(MR), >1.7% >1.4%
  • Emission threshold misfire rate (MR), > 1.7% >1.4%
  • Catalyst damage misfire rate (MR) >1.6-20%>400 |20-160>2.5-20%
  • Time from start, 0 Sec.
  • IAT, >-48° C
  • Time after engine start, Idle - 150 RPM
  • Engine torque, >5.47-23.4%
  • Camshaft revolutions 1
  • Engine speed range, 480-6800 RPM
  • Fuel cutoff, Not active
  • ECT at start, > -9° C
  • If ECT at start <-99° C wait until actual ECT >18° C
  • 1000 Rev.
  • 200 Rev.
  • 2 DCY
  • Immed.
P0303  Cylinder 3 Misfire Detected -- Check the Spark plugs.-- Check the intake system for leaks.-- Check the fuel pressure. Refer to FUEL PRESSURE, CHECKING .-- Check fuel injectors -N30, N31, N32, N33, -.-- Check the Ignition Coils with Power Output Stage -N70, N127, N291, N292-. Refer to IGNITION COILS WITH POWER OUTPUT STAGE, CHECKING .
  • Emission threshold 1st interval %(MR), >1.7% >1.4%
  • Emission threshold misfire rate (MR), > 1.7% >1.4%
  • Catalyst damage misfire rate (MR) >1.6-20%>400 |20-160>2.5-20%
  • Time from start, 0 Sec.
  • IAT, >-48° C
  • Time after engine start, Idle - 150 RPM
  • Engine torque, >5.47-23.4%
  • Camshaft revolutions 1
  • Engine speed range, 480-6800 RPM
  • Fuel cutoff, Not active
  • ECT at start, > -9° C
  • If ECT at start <-99° C wait until actual ECT >18° C
  • 1000 Rev.
  • 200 Rev.
  • 2 DCY
  • Immed.
P0304  Cylinder 4 Misfire Detected -- Check the Spark plugs.-- Check the intake system for leaks.-- Check the fuel pressure. Refer to FUEL PRESSURE, CHECKING .-- Check fuel injectors -N30, N31, N32, N33, -.-- Check the Ignition Coils with Power Output Stage -N70, N127, N291, N292-. Refer to IGNITION COILS WITH POWER OUTPUT STAGE, CHECKING .
  • Emission threshold 1st interval %(MR), >1.7% >1.4%
  • Emission threshold misfire rate (MR), > 1.7% >1.4%
  • Catalyst damage misfire rate (MR) >1.6-20%>400 |20-160>2.5-20%
  • Time from start, 0 Sec.
  • IAT, >-48° C
  • Time after engine start, Idle - 150 RPM
  • Engine torque, >5.47-23.4%
  • Camshaft revolutions 1
  • Engine speed range, 480-6800 RPM
  • Fuel cutoff, Not active
  • ECT at start, > -9° C
  • If ECT at start <-99° C wait until actual ECT >18° C
  • 1000 Rev.
  • 200 Rev.
  • 2 DCY
  • Immed.
P0321 Ignition/Distributor Engine Speed Input Circuit Range/Performance -- Check the Engine Speed (RPM) Sensor -G28-. Refer to ENGINE SPEED SENSOR G28, CHECKING .
  • Comparison of counted teeth and number of teeth +/- 1 tooth
  • Reference mark during normal operation Loss of reference gap
  • No reference gap during engine start
  • Reference gap, Detected
  • Engine speed, >Idle or vehicle speed <1 mph or vehicle speed >25 mph or vehicle speed signal, Error
  • Teeth during engine start Detected
  • Wait two crankshaft revs
 -
  • 2 DCY
P0322 Ignition/Distributor Engine Speed Input Circuit No Signal -- Check the Engine Speed (RPM) Sensor -G28-. Refer to ENGINE SPEED SENSOR G28, CHECKING .
  • No engine speed signal but phase signals during 4.5 cam shaft revs
  • Engine speed signal partly interrupted
  • Phase sensor, No DTC
 -
  • 2 DCY
P0324 Knock Control System Error -- Check theKnock Sensors -G61, G66-. Refer to KNOCK SENSORS G61 AND G66, CHECKING .
  • Integrator output ≤ 4 V
  • Integrator output slope≥ 200 V/sec
  • Parity errors in RAM> 25
  • Communication errors
  • SPI communication > 25
 ECT, > 40.5° C 160 Seconds 40 Seconds
  • 2 DCY
P0327 Knock Sensor 1 Circuit Low Input (Bank 1) -- Check theKnock Sensor -G61-. Refer to KNOCK SENSORS G61 AND G66, CHECKING . Lower threshold, 0.05-0.38 V
  • Engine speed, > 2400 RPM
  • ECT, > 40.5° C
  • Engine load, > 30%
  • Signal range check, No DTC
 2.5 Seconds
  • 2 DCY
P0328 Knock Sensor 1 Circuit High Input (Bank 1) -- Check theKnock Sensor -G61-. Refer to KNOCK SENSORS G61 AND G66, CHECKING . Upper threshold >4.58-30 V
  • Engine speed, > 2400 RPM
  • ECT, > 40.5° C
  • Engine load, > 30%
  • Signal range check, No DTC
 2.5 Seconds
  • 2 DCY
P0332 Knock Sensor 2 Circuit Low Input (Bank 2) -- Check theKnock Sensor -G66-. Refer to KNOCK SENSORS G61 AND G66, CHECKING . Lower threshold, 0.05-0.38 V
  • Engine speed, > 2400 RPM
  • ECT, > 40.5° C
  • Engine load, > 30%
  • Signal range check, No DTC
 2.5 Seconds
  • 2 DCY
P0333 Knock Sensor 2 Circuit High Input (Bank 2) -- Check theKnock Sensor -G66-. Refer to KNOCK SENSORS G61 AND G66, CHECKING . Upper threshold >4.58-30 V
  • Engine speed, > 2400 RPM
  • ECT, > 40.5° C
  • Engine load, > 30%
  • Signal range check, No DTC
 2.5 Seconds
  • Multiple
  • 2 DCY
P0340 Camshaft Position Sensor A Circuit (Bank 1 or single sensor) -- Check the Camshaft Position (CMP) Sensor -G40-. Refer to CAMSHAFT POSITION SENSOR G40, CHECKING . Cam adaption values out of range
  • >20 °KW
  • <-20 °KW
  • Difference of adapted and actual values >9°KW
  • Engine speed sensor, No DTC
  • Phase sensor, No DTC
  • Cam adaptation, Active
  • Engine speed sensor, No DTC
  • Phase sensor, No DTC
  • Camshaft adjustment, No DTC
  • Engine start, Completed
  • Cam adaptation, Completed
  • Camshaft in ref pos. for >2 sec.
 2 Seconds
  • 2 DCY
P0341 Camshaft Position Sensor A Circuit Range/Performance (Bank 1 or single sensor) -- Check the Camshaft Position (CMP) Sensor -G40-. Refer to CAMSHAFT POSITION SENSOR G40, CHECKING . Irregular number of phase changes Incorrect for 12 crank revs Engine speed signal and phase signal synchronized 0.2 Seconds
  • 2 DCY
P0342 Camshaft Position Sensor A Circuit Low Input (Bank 1 or single sensor) -- Check the Camshaft Position (CMP) Sensor -G40-. Refer to CAMSHAFT POSITION SENSOR G40, CHECKING . Irregular number of phase changes Incorrect for 12 crank revs Engine speed signal and phase signal synchronized 0.2 Seconds
  • 2 DCY
P0343 Camshaft Position Sensor A Circuit High Input (Bank 1 or single sensor) -- Check the Camshaft Position (CMP) Sensor -G40-. Refer to CAMSHAFT POSITION SENSOR G40, CHECKING . Irregular number of phase changes Incorrect for 12 crank revs Engine speed signal and phase signal synchronized 0.2 Seconds
  • 2 DCY
P0351 Ignition Coil A Primary/Secondary Circuit -- Check the Ignition Coils with Power Output Stage -N70-. Refer to IGNITION COILS WITH POWER OUTPUT STAGE, CHECKING .
  • Signal current, < 4.95-8.82 mA
  • Internal fault, changing error
  • Battery voltage, 9-16 V
  • Engine speed, 1400-5000 RPM
  • SW ignition counter diagnose, Not active
 -
  • 2 DCY
P0352 Ignition Coil B Primary/Secondary Circuit -- Check the Ignition Coils with Power Output Stage - N127-. Refer to IGNITION COILS WITH POWER OUTPUT STAGE, CHECKING .
  • Signal current, < 4.95-8.82 mA
  • Internal fault, changing error
  • Battery voltage, 9-16 V
  • Engine speed, 1400-5000 RPM
  • SW ignition counter diagnose, Not active
 -
  • 2 DCY
P0353 Ignition Coil C Primary/Secondary Circuit -- Check the Ignition Coils with Power Output Stage - N291-. Refer to IGNITION COILS WITH POWER OUTPUT STAGE, CHECKING .
  • Signal current, < 4.95-8.82 mA
  • Internal fault, changing error
  • Battery voltage, 9-16 V
  • Engine speed, 1400-5000 RPM
  • SW ignition counter diagnose, Not active
 -
  • 2 DCY
P0354 Ignition Coil D Primary/Secondary Circuit -- Check the Ignition Coils with Power Output Stage -N292-. Refer to IGNITION COILS WITH POWER OUTPUT STAGE, CHECKING .
  • Signal current, < 4.95-8.82 mA
  • Internal fault, changing error
  • Battery voltage, 9-16 V
  • Engine speed, 1400-5000 RPM
  • SW ignition counter diagnose, Not active
 -
  • 2 DCY
scientia non olet · About LEMON Manuals