1.8L 4-CYL 5V Turbo Generic Scan Tool, Engine Code(S): AEB

• 20 - Fuel supply
  • Fuel Supply System
    • Fuel Supply System
    • Safety precautions
    • Rules for cleanliness
    • Fuel pump, checking
    • Checking fuel pressure
    • Checking fuel delivery
  • Evaporative Emissions (EVAP) System
    • Evaporative Emissions (EVAP) System
    • EVAP system, leak detection
    • Evaporative Emission (EVAP) canister system, checking for proper seal
    • Evaporative Emission (EVAP) Canister Purge Regulator Valve N80, checking
    • Leak Detection Pump (LDP) V144, checking
• 21 - Turbocharger, G-Charger
  • Turbocharger
    • Turbocharger
    • General notes
    • Safety precautions
    • Rules of cleanliness
    • Wastegate Bypass Regulator Valve N75, checking
    • Barometric Pressure (BARO) Sensor F96, checking
  • Charge air system
    • General notes
    • Safety precautions
    • Rules of cleanliness
• 24 - Multiport Fuel Injection (MFI)
  • Motronic fuel injection system, servicing
    • Motronic fuel injection system, servicing
    • Safety Precautions
    • Safety Precautions - During A Test Drive
    • Rules of cleanliness
    • Technical data
  • Components, checking
    • Heated Oxygen Sensor (HO2S) G39 before catalytic converter, heater circuit checking
    • Oxygen Sensor (O2S) Behind Three Way Catalytic Converter (TWC) G130, heater circuit checking
    • Mass Air Flow (MAF) Sensor G70, checking
      • Notes
      • Checking voltage supply
      • Checking electrical circuit
    • Throttle Valve Control Module J338, checking
    • Engine Coolant Temperature (ECT) Sensor G62, checking
      • Notes
      • Testing if display is approx. - 40.0 °C
      • Testing if display approx. 140.0 °C
    • Intake Air Temperature (IAT) Sensor G72, checking
      • Notes
      • Testing if display approx. -40 °C or approx. -46 °C
      • Testing if display approx. 140 °C
    • Engine Speed (RPM) Sensor G28, checking
    • Fuel Injectors N30, N31, N32, N33, checking
  • Function tests
    • Heated Oxygen Sensor (HO2S) G39 and oxygen sensor regulation before catalytic converter, checking
    • Oxygen Sensor (O2S) Behind Three Way Catalytic Converter (TWC) G130 and oxygen sensor regulation behind catalytic converter, checking
  • Motronic Engine Control Module (ECM) J220
    • Function
    • Voltage supply, checking
    • Motronic Engine Control Module (ECM) J220, replacing
    • Fuel Pump (FP) Relay J17, checking
  • Additional signals (engine), checking
    • Speed Signal, checking
    • Motronic Engine Control Module (ECM) J220 to Instrument Cluster Control Module J285 K Line, checking
• 26 - Exhaust system, Emission controls
  • Exhaust system components, removing and installing
    • Exhaust system components, removing and installing
    • Three Way Catalytic Converter (TWC), checking
• 28 - Ignition/Glow plug System
  • Ignition, servicing
    • General notes on ignition system
    • Safety precautions
    • Test Data, Spark Plugs
    • Camshaft Position (CMP) Sensor G40, checking
    • Knock Sensor (KS) 1 G61 / Knock Sensor (KS) 2 G66, checking
    • Power Output Stage N122 and Ignition Coil, checking
• 38 - Automatic Transmission - Gears, Hydraulic Controls
  • Electrical components for 4 Spd. Automatic Transmission 01V, checking
• ST - Generic Scan Tool
  • On Board Diagnostic (OBD)
    • Generic Scan Tool (GST) Manual Contents
    • On Board Diagnostic (OBD) Systems
    • Serial Data Link (MIL) Illumination
    • Controller Area Network (CAN) Data Link
    • Electronic Power Control (EPC) Warning Lamp
  • Diagnostic modes
    • Diagnostic Modes Description
    • Diagnostic Mode 01: Obtain data
    • Diagnostic Mode 02: Obtain operating conditions
    • Mode 03: Interrogating fault memory
    • Interrogating the Fault Memory
    • Diagnostic Mode 04: Reset/delete diagnostic data
    • Diagnostic Mode 05: Check lambda test results
    • Diagnostic Mode 06: Checking test results of components that are not continuously monitored
    • Diagnostic Mode 07: Check test results of components that are continuously monitored
    • Diagnostic Mode 08: Tank leak test
    • Diagnostic Mode 09: Vehicle information
  • General Diagnosis
    • Preliminary check
  • Readiness Code
    • Readiness Code Description
  • Diagnostic Trouble Code (DTC) tables
    • SAE P0xxx-DTCs
    • SAE P1xxx-DTCs