LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Volkswagen >> 1996 >> Golf 2.0 B, Standard >> Repair and Diagnosis >> Quick Lookups >> DTC Index >> TEVES 04 Abs And Abs/EDL On Board Diagnostic (OBD)
April 5, 2026: LEMON Manuals is launched! Read the announcement.

TEVES 04 Abs And Abs/EDL On Board Diagnostic (OBD)

Diagnostic Trouble Code/Blind Code, Teves 04 ABS and ABS/EDL - DTC 00000/4444, 00257/1112 & 00259/1114

VAG 1551 scan tool printout Possible cause of malfunction Repairing malfunction
00000  4444   
No DTC recognized If "No DTC recognized" is displayed after carrying out repairs, On Board Diagnostic (OBD) program sequence has ended.
If, despite "No DTC recognized" being displayed, the ABS system does not operate properly, then proceed as follows:
  • Carry out road test exceeding 40 km/h (24 mph).
  • Again check DTC memory.

If there is still no DTC stored:
00257  1112     
ABS Inlet Valve, LF - N101 Faulty wire, connector or valve winding
  • Check wiring, connectors and valve winding

See test steps 17 and 37 in TEVES 04 ABS AND ABS/EDL ELECTRICAL TEST .
00259  1114     
ABS Inlet Valve, RF - N99 Faulty wire, connector or valve winding
  • Check wiring, connectors and valve winding

See test steps 18 and 38 in TEVES 04 ABS AND ABS/EDL ELECTRICAL TEST .
Diagnostic Trouble Code/Blind Code, Teves 04 ABS and ABS/EDL - DTC 00265/1132, 00267/1134, 00273/1211, 00274/1212, 00275/1213, 00276/1214, 00279/1223, 00280/1224 & 00283/1233

VAG 1551 scan tool printout Possible cause of malfunction Repairing malfunction
00265  1132     
ABS Outlet Valve, LF -N102 Faulty wire, connector or valve winding
  • Check wiring, connectors and valve winding

See test steps 21 and 37 (1)
00267  1134     
ABS Outlet Valve, RF -N100 Faulty wire, connector or valve winding
  • Check wiring, connectors and valve winding

See test steps 22 and 38 (1)
00273  1211     
ABS Inlet Valve, RR -N133 Faulty wire, connector or valve winding
  • Check wiring, connectors and valve winding

See test steps 20 and 40(1)
00274  1212     
ABS Inlet Valve, LR -N134 Faulty wire, connector or valve winding
  • Check wiring, connectors and valve winding

See test steps 19 and 39 (1)
00275  1213     
ABS Outlet Valve, RR -N135 Faulty wire, connector or valve winding
  • Check wiring, connectors and valve winding

See test steps 24 and 40 (1)
00276  1214     
ABS Outlet Valve, LR -N136 Faulty wire, connector or valve winding
  • Check wiring, connectors and valve winding

See test steps 23 and 39 (1)
00279  1223     
Differential Lock Valve 1 - N125 Faulty wire, connector or valve winding
  • Check wiring, connectors and valve winding

See test steps 25 and 41 (1)
00280  1224     
Differential Lock Valve 2 - N126 Faulty wire, connector or valve winding
  • Check wiring, connectors and valve winding

See test steps 26 and 41 (1)
00283  1233     
ABS Wheel Speed Sensor, LF-G47 Open circuit, short circuit or loose connection in:
  • ABS wheel speed sensor wire
  • Connector
  • ABS wheel speed sensor winding
  • Check wiring, connectors, ABS wheel speed sensor, Ground (GND) wiring to ABS control module and also capacitor for correct Ground (GND) connection

See test steps 7, 11 and 34 (1)
Mechanical malfunction (2) Excessive or insufficient air gap between ABS wheel speed sensor and impulse rotor (signal not OK)
  • Check installation of ABS wheel speed sensor and impulse rotor; clean if necessary
Signal outside tolerances (2) Impulse rotor and ABS wheel speed sensor dirty or damaged  
(1) See TEVES 04 ABS AND ABS/EDL ELECTRICAL TEST .
(2) Type of malfunction.
Diagnostic Trouble Code/Blind Code, Teves 04 ABS and ABS/EDL - DTC 00285/1241

VAG 1551 scan tool printout Possible cause of malfunction Repairing malfunction
00285  1241     
ABS Wheel Speed Sensor, RF-G45 Open circuit, short circuit or loose connection in:
  • ABS wheel speed sensor wire
  • Connector
  • ABS wheel speed sensor winding
  • Check wiring, connectors, ABS wheel speed sensor, Ground (GND) wiring to ABS control module and also capacitor for correct Ground (GND) connection

See test steps 6, 10 and 33 (1)
Mechanical malfunction (2) Excessive or insufficient air gap between ABS wheel speed sensor and impulse rotor (signal not OK)
  • Check installation of ABS wheel speed sensor and impulse rotor; clean if necessary
Signal outside tolerances (2) Impulse rotor and ABS wheel speed sensor dirty or damaged  
(1) See TEVES 04 ABS AND ABS/EDL ELECTRICAL TEST .
(2) Type of malfunction.
Diagnostic Trouble Code/Blind Code, Teves 04 ABS and ABS/EDL - DTC 00287/1243

VAG 1551 scan tool printout Possible cause of malfunction Repairing malfunction
00287  1243     
ABS Wheel Speed Sensor, RR -G44 Open circuit, short circuit or loose connection in:
  • ABS wheel speed sensor wire
  • Connector
  • ABS wheel speed sensor winding
  • Check wiring, connectors, ABS wheel speed sensor, Ground (GND) wiring to ABS control module and also capacitor for correct Ground (GND) connection

See test steps 8, 12 and 31 (1)
Mechanical malfunction (2) Excessive or insufficient air gap between ABS wheel speed sensor and impulse rotor (signal not OK)
  • Check installation of ABS wheel speed sensor and impulse rotor; clean if necessary
Signal outside tolerances (2) Impulse rotor and ABS wheel speed sensor dirty or damaged  
(1) See TEVES 04 ABS AND ABS/EDL ELECTRICAL TEST .
(2) Type of malfunction.
Diagnostic Trouble Code/Blind Code, Teves 04 ABS and ABS/EDL - DTC 00290/1311

VAG 1551 scan tool printout Possible cause of malfunction Repairing malfunction
00290  1311     
ABS Wheel Speed Sensor, LR -G46 Open circuit, short circuit or loose connection in:
  • ABS wheel speed sensor wire
  • Connector
  • ABS wheel speed sensor winding
  • Check wiring, connectors, ABS wheel speed sensor, Ground (GND) wiring to ABS control module and also capacitor for correct Ground (GND) connection

See test steps 9, 13 and 32 (1)
Mechanical malfunction (2) Excessive or insufficient air gap between ABS wheel speed sensor and impulse rotor (signal not OK)
  • Check installation of ABS wheel speed sensor and impulse rotor; clean if necessary
Signal outside tolerances (2) Impulse rotor and ABS wheel speed sensor dirty or damaged  
(1) See TEVES 04 ABS AND ABS/EDL ELECTRICAL TEST .
(2) Type of malfunction.
Diagnostic Trouble Code/Blind Code, Teves 04 ABS and ABS/EDL - DTC 00292/1313 & 00532/2234

VAG 1551 scan tool printout Possible cause of malfunction Repairing malfunction
00292  1313     
Hydraulic Energy Supply Pressure Level Pressure loss through leaks or air in the hydraulic unit and brake system
Mechanical malfunction (2) ABS hydraulic pump -V64- not producing sufficient pressure
   
00532  2234     
Supply Voltage (B+) Faulty wiring, connectors, fuse - S4-, ABS valves fuse -S54- or ABS relay -J102-
  • Check fuses, wiring, connectors, Ground (GND) wiring and the voltage supply to ABS control module

See test steps 1-4, 14 and 30 (1)
(1) See TEVES 04 ABS AND ABS/EDL ELECTRICAL TEST .
(2) Type of malfunction.
Diagnostic Trouble Code/Blind Code, Teves 04 ABS and ABS/EDL - DTC 00547/2133

VAG 1551 scan tool printout Possible cause of malfunction Repairing malfunction
00547  2133     
ABS Pressure Control Switch- F137 (2) Wire between terminal 13 and terminal 26 of ABS control module -J104- with ABS pressure control switch -F137- has connection to battery + or battery -
  • Visual check of wiring between terminal 13 and terminal 26. See appropriate WIRING DIAGRAMS article.
   
  • Disconnect multi-pin connector from ABS control module, connect to test box VAG 1598 and VAG 1598/10 and use multimeter (Fluke 83 or equivalent) to measure voltage between terminals:

    13 and 1 = max. 0.1 V

    26 and 1 = max. 0.1 V


See test step 29 (1)
(1) See TEVES 04 ABS AND ABS/EDL ELECTRICAL TEST .
(2) Type of malfunction.
Diagnostic Trouble Code/Blind Code, Teves 04 ABS and ABS/EDL - DTC 00599

VAG 1551 scan tool printout Possible cause of malfunction Repairing malfunction
00599     
Plausibility Pressure/Brake Light Switch Faulty wiring, connectors, ABS pressure control switch -F137-, fuse -S20- or brake light switch -F
  • Visual check of wire routing from brake light switch -F-, ABS pressure control switch -F137- and fuse - S20-

See test steps 5 and 29 (1)
  Time delay between brake light switch signal and pressure control switch signal excessive
  • Ensure that the brake light switch signal enters the ABS control module before the pressure control switch signal, if necessary adjust brake light switch

See Teves 04 ABS and ABS/EDL On Board Diagnostic (OBD)
(1) See TEVES 04 ABS AND ABS/EDL ELECTRICAL TEST .
Diagnostic Trouble Code/Blind Code, Teves 04 ABS and ABS/EDL - DTC 00634

VAG 1551 scan tool printout Possible cause of malfunction Repairing malfunction
00634     
Series Resistance - N159 Faulty wiring, connectors, EDL relay -J310- or EDL series resistance -N159-
  • Check wiring, connectors, EDL relay -J310- and EDL series resistance -N159-

See test steps 15, 35 and 36 (1)
   
  • Check EDL series resistance -N159- for continuity (using VW 1594 connector test kit and multimeter (Fluke 83 or equivalent) in 200 ohm resistance range); Specification: max. 2 Ω, replace if necessary
(1) See TEVES 04 ABS AND ABS/EDL ELECTRICAL TEST .
Diagnostic Trouble Code/Blind Code, Teves 04 ABS and ABS/EDL - DTC 00793/3231

VAG 1551 scan tool printout Possible cause of malfunction Repairing malfunction
00793  3231     
Brake Pedal Pos. Sensor-G100 Faulty wiring, connectors, brake pedal position sensor -G100- or short to battery positive (B+) or Ground
  • Check wiring, connectors and brake pedal position sensor -G100 -

See test steps 28 (1)
Mechanical malfunction (2)  
  • Unplug multi-pin connector from ABS control module, connect to test box VAG 1598 with adapter VAG 1598/10 and use multimeter (Fluke 83 or equivalent) to measure voltage between the terminals:

    16 and 1 = max. 0.1 V

    41 and 1 = max. 0.1 V
(1) See TEVES 04 ABS AND ABS/EDL ELECTRICAL TEST .
(2) Type of malfunction.
Diagnostic Trouble Code/Blind Code, Teves 04 ABS and ABS/EDL - DTC 01276/4133 & 65535/1111

VAG 1551 scan tool printout Possible cause of malfunction Repairing malfunction
01276  4133     
ABS Hydraulic Pump-V64 Faulty wiring, connectors, ABS hydraulic pump relay -J185-, ABS hydraulic pump -V64- or hydraulic pump sender -G101 -
  • Check wiring, connectors, ABS hydraulic pump relay -J185-, ABS hydraulic pump -V64- and hydraulic pump sender -G101 -

See test steps 15, 27, 35 and 36 (1)
Signal outside tolerances (2)    
65535  1111     
Control Module Malfunctioning Electrical malfunctions caused by outside interference, poor Ground (GND) connections, poor positive connections to ABS control module -J104-
  • Check wiring, connectors and Ground (GND) wires to ABS control module and voltage supply

See test steps 1-4, 14 and 30(1)
  ABS control module faulty
  • Replace ABS control module if necessary
(1) See TEVES 04 ABS AND ABS/EDL ELECTRICAL TEST .
(2) Type of malfunction.
scientia non olet · About LEMON Manuals