Data List / Active Test
WARNING: This page is about a different variant/trim than selected.
- DATA LIST
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.- Warm up the engine.
- Turn the power switch off.
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Enter the following menus: Chassis / ABS/VSC/ TRAC / Data List.
- According to the display on the Techstream, read the Data List.
ABS/VSC/TRAC:
DATA LIST - ABS/VSC/TRACTester Display Measurement Item/Range Normal Condition Diagnostic Note ABS Warning Light ABS warning light / ON or OFF ON: Warning light ON OFF: Warning light OFF - VSC Warning Light Master caution indicator light (VSC warning light) / ON or OFF ON: Indicator ON
OFF: Indicator OFF- Brake Warning Light Brake warning light / red (malfunction) / ON or OFF ON: Warning light ON
OFF: Warning light OFF- Slip Indicator Light Slip indicator light / ON or OFF ON: Indicator light ON
OFF: Indicator light OFF- ECB(1) Warning Light Brake warning light / yellow (minor malfunction) / ON or OFF ON: Warning light ON
OFF: Warning light OFF- Buzzer Skid control buzzer / ON or OFF ON: Buzzer ON
OFF: Buzzer OFF- Stop Light SW Stop light switch / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released- Parking Brake SW Parking brake switch / ON or OFF ON: Parking brake applied
OFF: Parking brake released- Reservoir Warning SW Brake fluid level warning switch / ON or OFF ON: Reservoir level low
OFF: Reservoir level normal- Main Idle SW Main idle switch / ON or OFF ON: Accelerator pedal released
OFF: Accelerator pedal depressed- Shift Lever Position Shift lever position information / P/N, R, D/M, 1st-6th/B, FAIL Actual shift lever position - Master Cylinder Sensor Master cylinder pressure sensor 1 reading / min.: 0 V, max.: 5 V When brake pedal is released: 0.3 to 0.9 V Reading increases when brake pedal is depressed Voltage of M/C Voltage of master cylinder pressure sensor / min.: -2.5 V, max.: 2.49 V Min.:-2.5 V
Max.: 2.49 V- Master Cylinder Sensor 2 Master cylinder pressure sensor 2 reading / min.: 0 V, max.: 5 V When brake pedal is released: 0.3 to 0.9 V Reading increases when brake pedal is depressed Voltage of M/C2 Voltage of master cylinder pressure sensor 2/min.:-2.5 V, max.: 2.49 V Min.:-2.5 V
Max.: 2.49 V- Stroke Sensor Stroke sensor / min.: 0 V, max.: 5 V When brake pedal is released: 0.7 to 1.3 V - Voltage of Stroke Sensor Voltage of stroke sensor / min.: -2.5 V, max.: 2.49 V Min.: -2.5 V
Max.: 2.49 V- Stroke Sensor 2 Stroke sensor 2 / min.: 0 V, max.: 5 V When brake pedal is released: 3.7 to 4.3 V - Voltage of Stroke Sensor 2 Voltage of stroke sensor 2 / min.: -2.5 V, max.: 2.49 V Min,:-2.5 V
Max.: 2.49 V- Accumulator Sensor Accumulator pressure sensor / min.: 0 V, max.: 5 V Specified value: 3.3 to 4.7 V - Deceleration Sensor Acceleration sensor 1 reading / min.: -18.52 m/s2 , max.: 18.39 m/s2 Min.: -18.52 m/s2
Max.: 18.39 m/s2Reading changes when vehicle is bounced Zero Point of Decele Memorized zero value / min.: -25.11 m/s2 , max.: 24.91 m/s2 Min.: -25.11 m/s2
Max.: 24.91 m/s2- Deceleration Sensor 2 Acceleration sensor 2 reading 7 min.: -18.52 m/s2 , max.: 18.39 m/ s2 Min.:-18.52 m/s2
Max.: 18.39 m/s2Reading changes when vehicle is bounced Zero Point of Decele 2 Memorized zero value / min.: -25.11 m/s2 , max.: 24.91 m/s2 Min.: -25.11 m/s2
Max.: 24.91 m/s2- Yaw Rate Sensor Yaw rate sensor 1 / min.: -128 degrees/sec, max.: 127 degrees/ sec. Vehicle stationary: 0 degrees/sec. Right turn: -128 to 0 degrees/sec. Left turn: 0 to 127 degrees/sec. - Zero Point of Yaw Rate Memorized zero value / min.: -128 degrees/sec, max.: 127 degrees/sec. Min.: -128 degrees/sec.
Max.: 127 degrees/sec.- Yaw Rate Sensor 2 Yaw rate sensor 2 / min.: -128 degrees/sec, max.: 127 degrees/ sec. Vehicle stationary: 0 degrees/sec. Right turn: -128 to 0 degrees/sec. Left turn: 0 to 127 degrees/sec. - Zero Point of Yaw Rate 2 Memorized zero value / min.: - 128 degrees/sec, max.: 127 degrees/sec. Min.: -128 degrees/sec.
Max.: 127 degrees/sec.- Steering Angle Sensor Steering angle sensor / min.: -3276.8 degrees, max.: 3276.7 degrees Left turn: Increase Right turn: Decrease - Zero Point of Steering Angle Memorized zero value / min.: -3276.8 degrees, max.: 3276.7 degrees Min.: -3276.8 degrees
Max.: 3276.7 degrees- FR W/C Sensor FR wheel cylinder pressure sensor / min.: 0 V, max.: 5 V When brake pedal is released: 0.3 to 0.9V - FL W/C Sensor FL wheel cylinder pressure sensor / min.: 0 V, max.: 5 V When brake pedal is released: 0.3 to 0.9 V - RR W/C Sensor RR wheel cylinder pressure sensor / min.: 0 V, max.: 5 V When brake pedal is released: 0.3 to 0.9 V - RL W/C Sensor RL wheel cylinder pressure sensor / min.: 0 V, max.: 5 V When brake pedal is released: 0.3 to 0.9 V - Lateral G Lateral G / min.: -25.11 m/s2 , max.: 24.91 m/s2 Min.: -25.11 m/s2
Max.: 24.91 m/s2- Forward and Rearward G Forward and backward G / min.: -25.11 m/s2 , max.: 24.91 m/s2 Min.: -25.11 m/s2
Max.: 24.91 m/s2- Yaw Rate Value Yaw rate value / min.:-128 degrees/sec, max.: 127 degrees/ sec. Min.: -128 degrees/sec.
Max.: 127 degrees/sec.- Steering Angle Value Steering angle value / min.: -3276.8 degrees, max.: 3276.7 degrees Min.: -3276.8 degrees
Max.: 3276.7 degrees- FR Wheel Speed FR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202 mph) Actual wheel speed Similar speed as indicated on speedometer FL Wheel Speed FL wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202 mph) Actual wheel speed Similar speed as indicated on speedometer RR Wheel Speed RR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202 mph) Actual wheel speed Similar speed as indicated on speedometer RL Wheel Speed RL wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202 mph) Actual wheel speed Similar speed as indicated on speedometer Vehicle Speed Maximum wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202 mph) Actual vehicle speed Speed indicated on speedometer FR Wheel Acceleration FR wheel acceleration / min.: -200.84 m/s2 , max.: 199.27 m/s2 Min.: -200.84 m/s2
Max.: 199.27 m/s2- FL Wheel Acceleration FL wheel acceleration / min.: -200.84 m/s2 , max.: 199.27 m/s2 Min.: -200.84 m/s2
Max.: 199.27 m/s2- RR Wheel Acceleration RR wheel acceleration / min.: -200.84 m/s2 , max.: 199.27 m/s2 Min.: -200.84 m/s2
Max.: 199.27 m/s2- RL Wheel Acceleration RL wheel acceleration / min.: -200.84 m/s2 , max.: 199.27 m/s2 Min.: -200.84 m/s2
Max.: 199.27 m/s2- FR Wheel ABS Ctrl Status FR wheel ABS control status /ON or OFF ON: During the control - FL Wheel ABS Ctrl Status FL wheel ABS control status / ON or OFF ON: During the control - RR Wheel ABS Ctrl Status RR wheel ABS control status / ON or OFF ON: During the control - RL Wheel ABS Ctrl Status RL wheel ABS control status / ON or OFF ON: During the control - BA Ctrl Status BA control status / ON or OFF ON: During the control - TRC (TRAC) Ctrl Status TRAC control status / ON or OFF ON: During the control - TRC (TRAC) Brake Ctrl Status TRAC brake control status / ON or OFF ON: During the control - FR Wheel VSC Ctrl Status FR wheel VSC control status / ON or OFF ON: During the control - FL Wheel VSC Ctrl Status FL wheel VSC control status / ON or OFF ON: During the control - RR Wheel VSC Ctrl Status RR wheel VSC control status / ON or OFF ON: During the control - RL Wheel VSC Ctrl Status RL wheel VSC control status / ON or OFF ON: During the control - Accelerator Opening Angle % The difference of a present accelerator/min.: 0%, max.: 128% Min.: 0%
Max.: 128%- FR Regenerative Request FR regenerative request torque / min.: 0 N*m, max.: 65536 N*m Min.: 0 N*m
Max.: 65536 N*m- FR Regenerative Operation FR regenerative operation torque / min.: 0 N*m, max.: 65536 N*m Min.: 0 N*m
Max.: 65536 N*m- BRAKE CONTROL - ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RR Regenerative RequestRR regenerative request torque / min.: 0 N*m, max.: 65536 N*m Min.: 0 N*m
Max.: 65536 N*m- RR Regenerative Operation RR regenerative operation torque / min.: 0 N*m, max.: 65536 N*m Min.: 0 N*m
Max.: 65536 N*m- Regenerative Cooperation Regenerative cooperation / ON or OFF ON: Operate
OFF: Not operate- ECB(1) Motor Relay ABS motor relay / ON or OFF ON: Motor relay ON
OFF: Motor relay OFF- ECB(1) Motor Relay 2 ABS motor relay 2 / ON or OFF ON: Motor relay ON
OFF: Motor relay OFF- ECB(1) Main Relay ABS main relay / ON or OFF ON: Main relay ON
OFF: Main relay OFF- ECB(1) Main Relay 2 ABS main relay 2 / ON or OFF ON: Main relay ON
OFF: Main relay OFF- ECB(1) Solenoid (SMC 1) Master cut solenoid (SMC1) / ON or OFF ON: Operate
OFF: Not operate- ECB(1) Solenoid (SMC2) Master cut solenoid (SMC2) / ON or OFF ON: Operate
OFF: Not operate- ECB(1) Solenoid (SCSS) Stroke simulator solenoid (SCSS) / ON or OFF ON: Operate
OFF: Not operate- SLAFR Solenoid Current Linear solenoid (SLAFR) current / min.: 0 A, max.: 3 A When brake pedal is released: 0 A - SLAFL Solenoid Current Linear solenoid (SLAFL) current/ min.: 0 A, max.: 3 A When brake pedal is released: 0 A - SLARR Solenoid Current Linear solenoid (SLARR) current/ min.: 0 A, max.: 3 A When brake pedal is released: 0 A - SLARL Solenoid Current Linear solenoid (SLARL) current/ min.: 0 A, max.: 3 A When brake pedal is released: 0 A - SLRFR Solenoid Current Linear solenoid (SLRFR) current/ min.: 0 A, max.: 3 A When brake pedal is released: 0 A - SLRFL Solenoid Current Linear solenoid (SLRFL) current/ min.: 0 A, max.: 3 A When brake pedal is released: 0 A - SLRRR Solenoid Current Linear solenoid (SLRRR) current /min.: 0 A, max.: 3 A When brake pedal is released: 0 A - SLRRL Solenoid Current Linear solenoid (SLRRL) current/ min.: 0 A, max.: 3 A When brake pedal is released: 0 A - FR Speed Open FR speed sensor open detection / ERROR or NORMAL ERROR: Momentary interruption NORMAL: Normal - FL Speed Open FL speed sensor open detection / ERROR or NORMAL ERROR: Momentary interruption NORMAL: Normal - RR Speed Open RR speed sensor open detection / ERROR or NORMAL ERROR: Momentary interruption NORMAL: Normal - RL Speed Open RL speed sensor open detection / ERROR or NORMAL ERROR: Momentary interruption NORMAL: Normal - Yaw Rate Open Yaw rate sensor open detection / ERROR or NORMAL ERROR: Momentary interruption NORMAL: Normal - Deceleration Open Acceleration sensor open detection / ERROR or NORMAL ERROR: Momentary interruption NORMAL: Normal - Steering Open Steering angle sensor open detection / ERROR or NORMAL ERROR: Momentary interruption NORMAL: Normal - Master Cylinder Open Master cylinder pressure sensor open detection / ERROR or NORMAL ERROR: Momentary interruption NORMAL: Normal - Master Cylinder 2 Open Master cylinder pressure sensor 2 open detection / ERROR or NORMAL ERROR: Momentary interruption NORMAL: Normal - Stroke Open Stroke sensor open detection / ERROR or NORMAL ERROR: Momentary interruption NORMAL: Normal - FR Wheel Cylinder Open FR wheel cylinder pressure sensor open detection / ERROR or NORMAL ERROR: Momentary interruption NORMAL: Normal - FL Wheel Cylinder Open FL wheel cylinder pressure sensor open detection / ERROR or NORMAL ERROR: Momentary interruption NORMAL: Normal - RR Wheel Cylinder Open RR wheel cylinder pressure sensor open detection / ERROR or NORMAL ERROR: Momentary interruption NORMAL: Normal - RL Wheel Cylinder Open RL wheel cylinder pressure sensor open detection / ERROR or NORMAL ERROR: Momentary interruption NORMAL: Normal - Accumulator Open Accumulator pressure sensor open detection / ERROR or NORMAL ERROR: Momentary interruption NORMAL: Normal - HV Communication Open Hybrid vehicle communication open detection / ERROR or NORMAL ERROR: Momentary interruption NORMAL: Normal - Number of DTC Number of DTC / min.: 0, max.: 255 Min.: 0
Max.: 255- (1) Electronically Controlled Brake System - ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts to operate without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
- Warm up the engine.
- Turn the power switch off.
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG).
- Turn the Techstream on.
- Enter the following menus: Chassis / ABS/VSC/ TRAC / Active Test.
- According to the display on the Techstream, perform the Active Test.
ABS / VSC / TRAC:
DATA LIST AND ACTIVE TEST - ABS / VSC / TRACTester Display Test Part Control Range Diagnostic Note ABS Warning Light ABS warning light Warning light ON / OFF Observe combination meter VSC Warning Light Master caution indicator light (VSC warning light) Indicator ON / OFF Observe combination meter Brake Warning Light Brake warning light / red (malfunction) Warning light ON / OFF Observe combination meter Slip Indicator Light Slip indicator light Indicator light ON / OFF Observe combination meter ECB(1) Warning Light Brake warning light / yellow (minor malfunction) Warning light ON / OFF Observe combination meter Buzzer Skid control buzzer Buzzer ON / OFF Buzzer can be heard Stop Light Relay Stop light control relay Relay ON / OFF Stop lights come on ECB(1) Main Relay ABS main relay Relay ON / OFF Operation sound of relay (clicking sound) can be heard ECB(1) Main Relay 2 ABS main relay 2 Relay ON / OFF Operation sound of relay (clicking sound) can be heard ECB(1) Motor Relay ABS motor relay Relay ON / OFF Operation sound of relay (clicking sound) and motor can be heard ECB(1) Motor Relay 2 ABS motor relay 2 Relay ON / OFF Operation sound of relay (clicking sound) and motor can be heard ECB(1) Solenoid (SMC1) Master cut solenoid (SMC1) Solenoid ON / OFF Operation sound of solenoid (clicking sound) can be heard ECB(1) Solenoid (SMC2) Master cut solenoid (SMC2) Solenoid ON / OFF Operation sound of solenoid (clicking sound) can be heard ECB(1) Control Invalid Electronically controlled brake system control invalid Control invalid ON / OFF Electronically controlled brake system control is disabled (braking with no accumulator assist) Accumulator Zero Down Accumulator zero down activation Activation ON / OFF Brake fluid in the accumulator makes noise Stroke Simulator Cut Valve Pattern Stroke simulator cut valve pattern activation Activation ON / OFF (Difficult to identify visually) Actuator Air Bleeding Pattern Actuator air bleeding pattern activation Activation ON / OFF When accumulator pressure lowers, pump operation creates sound Power Supply Air Bleeding Pattern 1 Power supply air bleeding pattern activation 1 Activation ON / OFF When accumulator pressure lowers, pump operation creates sound Power Supply Air Bleeding Pattern 2 Power supply air bleeding pattern activation 2 Activation ON / OFF When accumulator pressure lowers, pump operation creates sound RL Wheel Air Bleeding Pattern RL wheel air bleeding pattern activation Activation ON / OFF When accumulator pressure lowers, pump operation creates sound RR Wheel Air Bleeding Pattern RR wheel air bleeding pattern activation Activation ON / OFF When accumulator pressure lowers, pump operation creates sound Pump Check Pattern Pump check pattern activation Activation ON / OFF When accumulator pressure lowers, pump operation creates sound Drain System Air Bleeding Pattern Drain system air bleeding pattern activation Activation ON / OFF When accumulator pressure lowers, pump operation creates sound ECB(1) Solenoid (SLRRL) Value Close Linear solenoid (SLRRL) valve Valve close ON / OFF - ECB(1) Solenoid (SLARL) Value Close Linear solenoid (SLARL) valve Valve close ON / OFF - ECB(1) Solenoid (SLRRR) Value Close Linear solenoid (SLRRR) valve Valve close ON / OFF - ECB(1) Solenoid (SLARR) Value Close Linear solenoid (SLARR) valve Valve close ON / OFF - ECB(1) Solenoid (SLRFL) Value Close Linear solenoid (SLRFL) valve Valve close ON / OFF - ECB(1) Solenoid (SLAFL) Value Close Linear solenoid (SLAFL) valve Valve close ON / OFF - ECB(1) Solenoid (SLRFR) Value Close Linear solenoid (SLRFR) valve Valve close ON / OFF - ECB(1) Solenoid (SLAFR) Value Close Linear solenoid (SLAFR) valve Valve close ON / OFF - (1) Electronically Controlled Brake System