Common Specs & Procedures
GRAND VITARA COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | Refer to appropriate specifications included in text in AIR CONDITIONING SYSTEM article. | ||
| Torque | Refer to specifications included in text in AIR CONDITIONING SYSTEM article. Also refer to TIGHTENING TORQUE SPECIFICATIONS . | ||
| Axle Nut/Hub Nut | 160 ft. lbs. (220 N.m) | ||
| Battery | CHARGING SYSTEM SPECIFICATIONS | ||
| Brakes | |||
| Bleeding Sequence | AIR BLEEDING OF BRAKE SYSTEM | ||
| ABS | Refer to specifications included in text in REPAIR INSTRUCTIONS . | ||
| Front Brakes | Refer to specifications included in text in REPAIR INSTRUCTIONS . | ||
| Rear Brakes | Refer to specifications included in text in REPAIR INSTRUCTIONS . | ||
| Electronic Stability Control | Refer to specifications included in text in REPAIR INSTRUCTIONS . | ||
| Torque | |||
| ABS | TIGHTENING TORQUE SPECIFICATIONS | ||
| Front | TIGHTENING TORQUE SPECIFICATIONS | ||
| Rear | TIGHTENING TORQUE SPECIFICATIONS | ||
| Electronic Stability Control | TIGHTENING TORQUE SPECIFICATIONS | ||
| Charging | |||
| Generator | CHARGING SYSTEM SPECIFICATIONS | ||
| Torque | TIGHTENING TORQUE SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | ACCESSORY DRIVE BELT TENSION INSPECTION | ||
| Belt Routing | See figure under ACCESSORY DRIVE BELT TENSION INSPECTION . | ||
| Engine Cooling | |||
| General Service Specifications | Refer to specifications included in text in REPAIR INSTRUCTIONS . | ||
| Radiator Cap Pressure | 15.6 psi | ||
| Thermostat R & I | THERMOSTAT REMOVAL AND INSTALLATION | ||
| Water Pump R & I | WATER PUMP REMOVAL AND INSTALLATION | ||
| Engine Mechanical | |||
| Compression | COMPRESSION CHECK | ||
| Oil Pressure | More than 300-500 kPa (3.1-5.1 kgf/cm2 ,) 43.5-72.5 psi at 4,000 RPM | ||
| Overhaul | Refer to specifications included in text in ENGINE MECHANICAL . | ||
| Torque | TIGHTENING TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flexplate Torque | 51 ft. lbs. (70 N.m) | ||
| Fuel System | |||
| Fuel Filter Location | FUEL SYSTEM COMPONENTS | ||
| Pressure Specifications | 54.3-55.8 psi (375-385 kPa) | ||
| Fuel Pressure Test Procedure | FUEL PRESSURE CHECK | ||
| Fuel Pressure Release Procedure | FUEL PRESSURE RELIEF PROCEDURE | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Coil On Plug | ||
| Ignition Wires (Routing) | Coil On Plug | ||
| Spark Plugs | SPARK PLUG INSPECTION | ||
| Starting | |||
| Starter | CRANKING SYSTEM SPECIFICATIONS | ||
| Torque | TIGHTENING TORQUE SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | |||
| Front | For front suspension, refer to TIGHTENING TORQUE SPECIFICATIONS . | ||
| Rear | For rear suspension, refer to TIGHTENING TORQUE SPECIFICATIONS . | ||
| Wheel & Tire | |||
| Lug Nut Torque | 73 ft. lbs. (100 N.m) | ||