Fail-Safe Table

WARNING: This page is about a different car, the 2011 Suzuki SX4. However, it is still accessible from the selected car via links, so may be relevant.

When any of the following DTC(s) is detected, ESP® system is in fail-safe mode per its DTC and ABS, EBD, traction control, stability control are deactivated until the resolution is applied.

FAIL-SAFE TABLE

DTC No.

Fail-safe operation

Fail-safe condition resolutive

ABS

EBD

Traction control/stability control

C1016

C1017

When ESP® control module detects the system as normal, after ignition switch turned OFF to ON.

C1020

C1021

⁽¹⁾

C1022

⁽¹⁾

When ESP® control module detects the system as normal. And estimated vehicle speed exceeds 14 km/h (9 mile/h), after ignition switch turned OFF to ON.

C1023

When ESP® control module detects the system as normal, after ignition switch turned OFF to ON.

C1024

C1025

⁽¹⁾

C1026

⁽¹⁾

When ESP® control module detects the system as normal. And estimated vehicle speed exceeds 14 km/h (9 mile/h), after ignition switch turned OFF to ON.

C1027 ⁽²⁾

C1028

When ESP® control module detects the system as normal, after ignition switch turned OFF to ON.

C1031

⁽¹⁾

C1032

⁽¹⁾

When ESP® control module detects the system as normal. And estimated vehicle speed exceeds 14 km/h (9 mile/h), after ignition switch turned OFF to ON.

C1033

⁽¹⁾

When ESP® control module detects the system as normal, after ignition switch turned OFF to ON.

C1034

When ESP® control module detects the system as normal.

C1035

⁽¹⁾

When ESP® control module detects the system as normal, after ignition switch turned OFF to ON.

C1036

⁽¹⁾

When ESP® control module detects the system as normal. And estimated vehicle speed exceeds 14 km/h (9 mile/h), after ignition switch turned OFF to ON.

C1037

When ESP® control module detects the system as normal, after ignition switch turned OFF to ON.

C1038

C1039

C1040 ⁽³⁾

When ESP® control module detects the system as normal, after ignition switch turned OFF to ON. (ESP® control failure)
When ESP® control module detects the system as normal. (ABS control failure)

C1041

When ESP® control module detects the system as normal, after ignition switch turned OFF to ON.

C1042

C1043

C1044

C1045

C1046

C1051

C1052

C1053

C1054

When ESP® control module detects the system as normal, after ignition switch turned OFF to ON.

C1055

C1056

C1057

⁽⁴⁾

When ESP® control module detects the system as normal.

C1061

When ESP® control module detects the system as normal. And estimated vehicle speed exceeds 14 km/h (9 mile/h), after ignition switch turned OFF to ON.

C1063

⁽⁵⁾

When ESP® control module detects the system as normal, after ignition switch turned OFF to ON.

C1071

C1075

Steering angle sensor calibration completed.

C1091

When ESP® control module detects the system as normal, after ignition switch turned OFF to ON.

C1094

C1096

U0073

U0100

U0101

U0114

U0123

U0126

O: Activated
-: Deactivated

NOTE:

⁽¹⁾	If one or two wheel speed sensor is defective, EBD control function is activated. If three or more wheel speed sensor are defective, EBD control function is deactivated.

⁽²⁾	ESP® OFF mode is cancelled and all control functions are activated.

⁽³⁾	If the control module requests pressure-decrease or pressure-hold for specified time or longer for all wheels, the state is judged failure, and the emergency brake is applied. The state returns to be normal after stop of the vehicle, if any other failures are not found.

⁽⁴⁾	EBD control function is activated only power supply circuit becomes 7.6 - 9.6 V malfunction.

⁽⁵⁾	EBD control function is activated only solenoid valve power supply driver circuit is shorted to power circuit and/or output circuit from control unit is opened malfunction.