LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Suzuki >> 2012 >> SX4 Base >> Repair and Diagnosis >> External Pages >> Different car >> Section 71 (Engine General Information And Diagnosis) >> Diagnostic Information and Procedures >> DTC P2122/P2123: Throttle/Pedal Position Sensor/Switch "D" Circuit Low/Throttle/Pedal Position Sensor/Switch "D" Circuit High >> DTC Troubleshooting
April 5, 2026: LEMON Manuals is launched! Read the announcement.

DTC Troubleshooting

WARNING: This page is about a different car, the 2011 Suzuki SX4. However, it is still accessible from the selected car via links, so may be relevant.
DIAGNOSTIC INFORMATION AND PROCEDURES REFERENCE CHART

Step Action YES NO
1  Was "Engine and Emission Control System Check" performed?  Go to Step 2. Go to ENGINE AND EMISSION CONTROL SYSTEM CHECK .
2  Accelerator pedal assembly (with APP sensor) mounting check 
  1. Check that accelerator pedal assembly (with APP sensor) has been mounted to vehicle body properly (no pinched floor carpet, etc.).

Is it in good condition? 		 Go to Step 3. Reinstall accelerator pedal assembly (with APP sensor) properly. Refer to ACCELERATOR PEDAL POSITION (APP) SENSOR ASSEMBLY REMOVAL AND INSTALLATION .
3  APP sensor (main) power supply circuit check 
  1. Turn OFF ignition switch and disconnect connector from accelerator pedal assembly (with APP sensor).
  2. Check for proper terminal connection to accelerator pedal assembly (with APP sensor) connector.
  3. If connections are OK, turn ignition switch to ON position.
  4. Check that voltage between APP sensor (main) power supply circuit (A1) and ground circuit (A3) is 5 V.

Is it in good condition? 		 Go to Step 6. Go to Step 4.
4  APP sensor (main) power supply circuit check 
  1. Check that voltage between APP sensor (main) power supply circuit (A1) and vehicle body ground is 5 V.

Is it in good condition? 		 Repair or replace defective wire harness. If this DTC is detected again, substitute a known-good ECM and recheck DTC Go to Step 5.
5  APP sensor (main) power supply circuit check 
  1. Turn OFF ignition switch and disconnect connectors from ECM.
  2. Check for proper terminal connection to ECM connectors.
  3. If connections are OK, check that APP sensor (main) power supply circuit (A1) is as follows.
    • Wiring harness resistance of APP sensor (main) power supply circuit is less than 3 Ω.
    • Insulation resistance of APP sensor (main) power supply circuit is infinity between accelerator pedal assembly (incorporated with APP sensor) connector and vehicle body ground.
    • Insulation resistance of wire harness is infinity between APP sensor (main) power supply terminal and each terminal at APP sensor connector.
    • Circuit voltage of APP sensor (main) power supply circuit is 0 - 1 V with ignition switch in ON position.

Is it in good condition? 		 Substitute a known-good ECM and recheck DTC Repair or replace defective wire harness.
6  APP sensor (main) signal circuit check 
  1. Turn OFF ignition switch and disconnect connectors from ECM.
  2. Check for proper terminal connection to ECM connectors.
  3. If connections are OK, check that APP sensor (main) signal circuit (A2) is as follows.
    • Wiring harness resistance of APP sensor (main) signal circuit is less than 3 Ω.
    • Insulation resistance of APP sensor (main) signal circuit is infinity between accelerator pedal assembly (with APP sensor) connector and vehicle body ground.
    • Insulation resistance of wire harness is infinity between APP sensor (main) signal terminal and each terminal at accelerator pedal assembly (with APP sensor) connector.
    • Circuit voltage of APP sensor (main) signal circuit is 0 - 1 V with ignition switch in ON position.

Is it in good condition? 		 Go to Step 7. Repair or replace defective wire harness.
7  APP sensor check 
  1. Check APP sensor. Refer to ACCELERATOR PEDAL POSITION (APP) SENSOR ASSEMBLY INSPECTION .

Is it in good condition? 		 Substitute a known-good ECM and recheck DTC Replace accelerator pedal assembly (incorporated with APP sensor).
scientia non olet · About LEMON Manuals