DTC Table
WARNING: This page is about a different car, the 2010 Suzuki Kizashi. However, it is still accessible from the selected car via links, so may be relevant.
NOTE:
- The DTC No. with asterisk (*) does not memorize history DTC.
- When BCM detects DTC B1120, display "SERVICE BCM SYSTEM" on the information display in combination meter to warn the driver.
DTC DETECTING CONDITION CHART
| DTC | DTC name | DTC detecting condition |
|---|---|---|
| B1120* | BCM Internal Defect | BCM internal failure. |
| B1132 | 5 V System Voltage too Low | "G05-8" terminal voltage is lower than 2.5 V for specified time continuously. |
| B1133 | Battery Voltage too High | Backup power supply circuit voltage from "DOME" fuse is continuously higher than 16.0 V for specified time. |
| B1141 | Outside Air Temperature (Ambient Temperature) Sensor Circuit Open | Outside air temperature sensor signal circuit voltage is higher than 4.85 V for specified time continuously. |
| B1142 | Outside Air Temperature (Ambient Temperature) Sensor Circuit Short to Ground | Outside air temperature sensor signal circuit voltage is lower than 0.15 V for specified time continuously. |
| B1145 | A/C Evaporator Temperature Sensor Circuit High | Evaporator temperature sensor signal circuit voltage is higher than 4.85 V for specified time continuously. |
| B1146 | A/C Evaporator Temperature Sensor Circuit Low | Evaporator temperature sensor signal circuit voltage is lower than 0.15 V for specified time continuously. |
| B1157 | Air Bag Deployment Signal Input | Air bag deployment signal is fed from SDM to BCM. |
| B1670* | Rain/Light Sensor Malfunction | BCM detected malfunction related to rain/light sensor. |
| B1680 | CAN Invalid Data from ECM | BCM detected abnormality in control data transmitted by ECM through CAN communication. |
| B1681 | CAN Invalid Data from TCM | BCM detected abnormality in control data transmitted by TCM through CAN communication. |
| B1682 | CAN Invalid Data from 4WD Control Module | BCM detected abnormality in control data transmitted by 4WD control module through CAN communication. |
| B1683* | Yaw Rate Information Mismatched | Difference between target yaw rate calculated by BCM and actual yaw rate transmitted from ESP® control module via CAN communication is continuously higher than specified value for specified time. |
| B1684 | CAN Invalid Data from P/S Control Module | BCM detected abnormality in control data transmitted by P/S control module through CAN communication. |
| B1685* | CAN Invalid Data from ESP® Control Module |
|
| B1686* | CAN Invalid Data from Longitudinal G Sensor | BCM detected abnormality in longitudinal G data transmitted by ESP® control module through CAN communication. |
| B1687* | CAN Invalid Data from Lateral G Sensor | BCM detected abnormality in lateral G data transmitted by ESP® control module through CAN communication. |
| B1688* | CAN Invalid Data from Yaw Rate Sensor | BCM detected abnormality in yaw rate data transmitted by ESP® control module through CAN communication. |
| B1689* | CAN Invalid Data from Wheel Speed Sensor | BCM detected abnormality in wheel speed data transmitted by ESP® control module through CAN communication. |
| B1690* | Steering Angle Sensor Malfunction |
|
| B1691 | CAN Invalid Data from Steering Angle Sensor | BCM received abnormal CAN communication data from steering angle sensor. |
| B1692 | CAN Invalid Data from Steering Angle Sensor | BCM received abnormal CAN communication data from steering angle sensor. |
| B1693 | CAN Invalid Data from P/S Control Module | BCM received abnormal CAN communication data from P/S control module. |
| B1694 | CAN Invalid Data from P/S Control Module | BCM received abnormal CAN communication data from P/S control module. |
| B1695 | CAN Invalid Data from ESP® Control Module | BCM received abnormal CAN communication data from ESP® control module. |
| B1696 | CAN Invalid Data from ESP® Control Module | BCM received abnormal CAN communication data from ESP® control module. |
| B1901* | Internal Control Module Memory Check Sum Error | BCM internal failure. (check sum error) |
| B1902* | Control Module Programming Error | BCM internal failure. (programming error) |
| U0073 | Control Module Communication Bus Off | BCM fails to transmit and receive the data via CAN for specified time continuously. |
| U0100 | Lost Communication with ECM | Receiving error of the data from ECM via CAN for specified time continuously. |
| U0101 | Lost Communication with TCM | Receiving error of the data from TCM via CAN for specified time continuously. |
| U0114 | Lost Communication with 4-Wheel Drive Control Module | Receiving error of the data from 4WD control module via CAN for specified time continuously. |
| U0121 | Lost Communication with ABS/ESP® Control Module | Receiving error of the data from ESP® control module via CAN for specified time continuously. |
| U0126 | Lost Communication with Steering Angle Sensor | Receiving error of the data from steering angle sensor via CAN for specified time continuously. |
| U0131 | Lost Communication with Power Steering Control Module | Receiving error of the data from P/S control module via CAN for specified time continuously. |
| U0141 | Lost Communication with Body Control Module "keyless start" | Receiving error of the data from keyless start control module via CAN for specified time continuously. |
| U0151 | Lost Communication with Restraints Control Module | Receiving error of the data from SDM via CAN for specified time continuously. |
| U0155 | Lost Communication with Instrument Panel Cluster (IPC) Control Module | Receiving error of the data from combination meter via CAN for specified time continuously. |
| U0164 | Lost Communication with HVAC Control Module | Receiving error of the data from HVAC control module via CAN for specified time continuously. |
| U0231 | Lost Communication with Rain Sensing Module | Receiving error of the data from rain/light sensor via CAN for specified time continuously. |