LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Suzuki >> 2011 >> Kizashi S, FWD, Standard >> Repair and Diagnosis >> Engine Performance >> System >> Engine General Information And Diagnosis >> Diagnostic Information and Procedures >> ECM Power and Ground Circuit Check >> Troubleshooting
April 5, 2026: LEMON Manuals is launched! Read the announcement.

ECM Power and Ground Circuit Check: Troubleshooting

NOTE:
  • Before troubleshooting, perform following items.
    • Be sure to read "Precautions for ECM Circuit Inspection" under PRECAUTIONS FOR ENGINE .
    • When measuring circuit voltage and/or pulse signal at ECM connector, connect special tool to ECM and ECM connectors, see Inspection of ECM and Its Circuits .
    • Be sure to confirm related fuses of ECM power circuit for not blown out.

      If fuse is blown out, replace fuse(s) and check circuits connected to blown fuse(s) for short circuit to ground.

    • Confirm that battery voltage is 12 V or more.
  • For "Ignition mode" described in the following table, it means power supply mode in keyless push start system.

    For more details of ignition mode, refer to DESCRIPTION OF KEYLESS ENGINE START FUNCTION .

  1. Check ECM power supply circuit as follows.
    1. Confirm that ignition mode of keyless push start system is "OFF".
    2. Disconnect ECM connectors.
    3. Check each terminal of ECM connectors for proper connection.
    4. Measure voltage between each terminal of ECM connector and ground in the following table.

      If each measured voltage is out of specified voltage, repair or replace related part.

      VOLTAGE SPECIFICATION

      Terminals Specified voltage Related part
      Ignition mode: OFF Ignition mode: ON
      "E01-2" to ground Battery voltage Battery voltage "F1" circuit
      "E01-29" to ground 0 -1 V
      • "E1" circuit
      • Junction block
      "E01-60" to ground Battery voltage
      • "G1" circuit
      • "G2" circuit
      • Main relay
    5. Confirm that ignition mode of keyless push start system is "OFF".
    6. Connect ECM connectors.
    7. Measure voltage between each terminal of ECM connector and ground in the following table.

      If each measured voltage is out of specified voltage, repair or replace related part.

      VOLTAGE SPECIFICATION

      Terminals Specified voltage Related part
      5 sec. after changing the ignition mode of keyless push start system to "OFF" Ignition mode: ON
      "E01-60" to ground Battery voltage 0 - 1 V ECM
      "E01-1" to ground 0 - 1 V Battery voltage
      • "G3" circuit
      • "G4" circuit
      • Main relay
      "E01-16" to ground 0 - 1 V Battery voltage
      • "G3" circuit
      • "G5" circuit
      • Main relay
  2. Check throttle actuator power supply circuit as follows.

    If each measured voltage is out of specified voltage, repair or replace related part.

    VOLTAGE SPECIFICATION

    Terminals Specified voltage Related part
    5 sec. after changing the ignition mode of keyless push start system to "OFF" Ignition mode: ON
    "E01-49" to ground 0 - 1 V
    • "C2" circuit
    • ECM
    "E01-31" to ground 0 - 1 V Battery voltage
    • "C1" circuit
    • "C2" circuit
    • "C3" circuit
    • "C4" circuit
    • Throttle actuator control relay
    • ECM
  3. Check ECM ground circuit as follows.

    If each measured voltage is out of specified voltage, repair ECM ground circuits.

    VOLTAGE SPECIFICATION

    Terminals Specified voltage Related part
    Ignition mode: OFF Ignition mode: ON
    "E01-2" to "C01-15" Battery voltage Battery voltage "H1" circuit
    "E01-2" to "C01-29" "H3" circuit
    "E01-2" to "C01-30" "H2" circuit
    "E01-2" to "C01-49" "H5" circuit
    "E01-2" to "C01-50" "H6" circuit
    "E01-2" to "C01-58" "H4" circuit
  4. Check each sensor power supply circuit as follows.

    If measured voltage is within specified voltage, ECM power and ground circuits is in good condition. If each measured voltage is out of specified voltage, repair or replace related part.

    VOLTAGE SPECIFICATION

    Terminals Specified voltage Related part
    Ignition mode: OFF Ignition mode: ON
    "E01-56" to ground 0 - 1 V 4 - 6 V
    • "A1" circuit
    • APP sensor
    • ECM
    "E01-55" to ground
    • "A2" circuit
    • APP sensor
    • ECM
    "E01-57" to ground
    • "B1" circuit
    • A/C refrigerant pressure sensor
    • ECM
    "C01-41" to ground
    • "D1" circuit
    • TP sensor
    • ECM
    "E01-40" to ground
    • "I1" circuit
    • EVAP leak check module
    • ECM
scientia non olet · About LEMON Manuals