Keyless Remote Controller Registration Procedure (TS 03 12170)

Registration Procedure

1. Begin by confirming that the SDT scan tool has the latest software version installed, and the Date & Time is properly set.
2. Install the immobilizer cable to the SDT scan tool (A), then connect the scan tool to the vehicles DLC (Data Link Connector) (1)
3. Turn the vehicle ignition "On" without starting the engine by pushing the vehicle's Engine Start/Stop button twice without depressing the brake or clutch pedal.
4. Check that the warning lights (Battery, Oil, MIL, etc.) are illuminated on the instrument panel to confirm the ignition is "On"
5. Power on the SDT scan tool. With the immobilizer cable connected, the scan tool will automatically start up at the Immobilizer screen.
   NOTE: Once the SDT is powered on, if the screen pictured to the right is displayed with the immobilizer cable connected, it indicates that the Immobilizer Cable has not yet been activated to the scan tool. Please call (714) 996-7040 ext. 2062 to obtain the activation code for your cable, and refer to TSB number TS 01 12158R for instructions to setup the Immobilizer Cable.
6. Begin by selecting the "ID Code Reading" option from the Immobilizer screen.
7. The screen will describe the function which has been chosen.
8. Push "Next".
9. Record the 20 digit "ID Code" that is displayed on the scan tool screen.
10. Push "Exit".
11. You will also need to have the VIN number of the vehicle, as well as the serial number from your immobilizer cable before going to your computer to request the passwords from SuzukiPitstopPlus.com.
12. Using the PC/Laptop, log on to SuzukiConnect.com. When the home page has loaded, place the mouse cursor over the "SERVICE" tab, a dropdown list will appear, follow it down to the "SuzukiPitStopPLUS" option, another list will appear to the right, slide the cursor over and click on the "Home" option.
13. A new window will appear and open to the SuzukiPitstopPlus.com home page. Click on the "Vehicle Security Systems" menu bar.
14. At the Vehicle Security Systems page you are offered two (2) options:
    • "Request Vehicle Key Code"
    • "Request Immobilizer Password"
15. Click on "Continue" to the right of Request Immobilizer Password.
16. Read the Terms & Conditions document, then click the "Accept" button just below the bottom left corner of the dialog box.
17. When the Terms & Conditions are accepted and the Online Immobilizer Password Request page is loaded, begin filling in the information fields. All fields are required to be filled in for security purposes. Requests are never to be made for any person, or vehicle, that is not present and being repaired at an authorized Suzuki Dealer.

    The information needed is:

    • Technician (requester) First & Last name
    • The requester's Title
    • Dealer number (Dealer Code)
    • Cable Serial # (found on the Immobilizer cable)
    • VIN (Vehicle Identification Number)
    • Encrypted Pin (20 digit ID Code retrieved in steps  5 &  6 above)
18. Click "Continue"
19. The information will be computed and the Immobilizer password page will be displayed. Record both Password 1 and Password 2, then return to the vehicle and SDT scan tool.
20. On the SDT main immobilizer menu screen, select the "Immobilizer" option.
21. Following the instruction prompts on the SDT scan tool screen, if the ignition is "Off", turn the ignition switch "On" by pressing the ignition start button twice without depressing either the brake or clutch pedal.  Confirm the vehicle ignition is on by observing the proper warning lights are illuminated in the instrument panel.
22. Press "Next".
23. At the password screen you will be asked to enter the "Password #1" retrieved from SuzukiPitstopPlus.com. Key in the six digit password.
24. Press "OK".
25. The next screen asks you to enter the "Password #2". Key in the eight digit alphanumeric password.
26. Press "OK".
27. The ignition should still be "ON", but in case it is not, please turn the ignition on by pushing the ignition start button twice without pressing the brake or clutch pedals. 
28. Press "Next".
29. This screen is a reminder to be sure that all the remote controllers that are to be registered are in the vehicle.
30. Press "Next".
31. To add an additional or replacement remote controller, select "Immobilizer Key Registration".
32. Press "Next".
33. Please read and heed the "Important!" notice that reminds you that all previously registered information will be cleared, and to prepare all remotes to be registered.
34. Press "Next".
35. The next screen represents the step that actually clears all the previously registered information, and offers a final chance to ensure you have all remotes ready to proceed.
36. Press "OK".
37. Enter the current year and month.
38. Press "Next".
39. Take one of the Keyless Remote Controllers to be registered and hold it up to the Engine Start/Stop button.
40. While holding the remote up to the start switch, press "Next".
41. The screen will change slightly, now displaying "Registering" above the instruction "Hold by applying the remote...", continue holding the remote up to the Engine Start/Stop button until the screen changes.
42. If there was a problem recognizing a remote controller, an error massage will appear, and it will offer another attempt to register the remote. Again hold the desired remote up against the Engine Start/Stop button, and press "Next".
    NOTE: If the remote controller will not register and the "Cancel" button is pressed, the SDT scan tool will end the registration process and go to the Immobilizer start screen. DO NOT  turn off the ignition, this will result in the need to replace the controller. Simply begin the registration process again, using the same passwords as before.
43. Once the remote controller is recognized, the screen will change to read "The remote controller was registered.
44. Press "Next" to continue programming the remaining remote controllers, and continue to Step 45. If only one remote controller is being registered, press "Exit" and jump to Step  50.
45. Set the registered remote aside where it won't be confused with those remaining to be registered.
46. Keeping the SDT powered on, push the Engine Start/Stop button once to turn the ignition "Off" (the warning lights in instrument panel will go off), then push Engine Start/Stop button twice more to turn the ignition back on.
47. Hold another remote controller up to the Engine Start/Stop button and press "Next".
48. Once the remote is registered, to program another remote press "Next", and repeat Steps  43- 47 until the remaining remote controllers are registered.
49. Press "Exit" when all remotes have been registered.
50. A screen will display a summary of the registration process, including the total number of Keyless Remote Controllers that are now registered, the Year and Month that you entered during this process, vehicle info, etc., the registration process is now completed.
51. Press "Next".
52. Test the Keyless Remote controllers by starting the engine, and operating the door locks (start vehicle with only one remote inside the car, then repeat with all other remotes)
53. Now that the "Immobilizer Registration" procedure has been completed, all of the internal codes and passwords will be changed. If the "Immobilizer Registration" process needs to be done again, the "ID Code Reading" will need to be performed again to retrieve and apply the new code to SuzukiPitstopPlus.com, refer to Steps  6- 19.