LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Suzuki >> 2009 >> Grand Vitara Premium, AWD, Standard >> Repair and Diagnosis >> Brakes >> Traction Control >> Electronic Stability Program >> Diagnostic Information and Procedures >> DTC Table
April 5, 2026: LEMON Manuals is launched! Read the announcement.

DTC Table

CAUTION: Be sure to perform ELECTRONIC STABILITY PROGRAM CHECK  before starting diagnosis.
DTC REFERENCE CHART

DTC (displayed on SUZUKI scan tool) Diagnostic Items Detecting condition (DTC will be set when detecting) ABS warning light EBD warning light ESP® warning light
NO DTC Normal - - - -
C1015 Longitudinal G sensor in yaw rate/G sensor assembly failure Longitudinal G sensor signal is out of specified range. (for 4WD vehicle) • - •
C1016 Brake light switch failure Vehicle behavior and brake light switch signal is disagreed for specified time. - - -
C1017 Lateral G sensor in yaw rate/G sensor assembly failure Lateral G sensor signal is out of specified range. - - •
C1018 Brake fluid level switch failure
  • Brake fluid level is too low.
  • Input voltage of brake fluid level switch to BCM is low.
 - • •
C1020 Master cylinder pressure sensor power supply failure Power supply voltage to master cylinder pressure sensor in ESP® hydraulic unit/control module assembly is too low. - - •
C1021 RF Wheel speed sensor circuit failure Wheel sensor signal is out of specified range. • (1) •
C1025 LF
C1031 RR
C1035 LR
C1022 RF Wheel speed sensor or encoder failure Abnormal wheel speed sensor signal is detected. • (1) •
C1026 LF
C1032 RR
C1036 LR
C1023 Yaw rate sensor in yaw rate/G sensor assembly failure
  • Yaw rate sensor signal is out of range.
  • Vehicle behavior and yaw rate signal is disagreed.
 - - •
C1024 Steering angle sensor circuit failure
  • Steering angle sensor internal defect is detected by CPU in steering angle sensor.
  • Steering angle sensor signal is out of specified range.
 - - •
C1027 ESP® OFF switch circuit failure Mechanical switch failure, failure in switch wiring is shorted to ground. - - -
C1028 Master cylinder pressure sensor circuit failure Input signal voltage from master cylinder pressure sensor in ESP® control module is too high or low. - - •
C1034 Yaw rate/G sensor assembly power supply failure Power supply voltage of yaw rate/G sensor assembly is too high when ignition switch OFF. (2) -  
Power supply voltage of yaw rate/G sensor assembly is too low when ignition switch ON.
C1037 Steering angle sensor power supply failure Power supply voltage to steering angle sensor is too low. - - -
C1038 Steering angle sensor detect rolling counter failure from ESP® control module ESP® control module rolling counter failure is detected by steering angle sensor. - - •
C1039 Yaw rate/G sensor assembly internal failure Yaw rate/G sensor assembly internal failure is detected. (2) - •
C1040 Stability control system function failure Stability control is active for more than specified time without yaw rate change. - - •
C1041 RF Inlet solenoid valve circuit failure Mismatching solenoid output and solenoid monitor is detected.      
C1042 Outlet solenoid valve circuit failure
C1045 LF Inlet solenoid valve circuit failure
C1046 Outlet solenoid valve circuit failure
C1051 RR Inlet solenoid valve circuit failure
C1052 Outlet solenoid valve circuit failure
C1055 LR Inlet solenoid valve circuit failure
C1056 Outlet solenoid valve circuit failure
C1043 Master cylinder cut solenoid valve circuit No.1 failure
C1044 Master cylinder cut solenoid valve circuit No.2 failure
C1053 Low pressure solenoid valve circuit No.1 failure
C1054 Low pressure solenoid valve circuit No.2 failure
C1057 ESP® control module power supply circuit failure (3) ESP® control module power supply voltage is too high.      
ESP® control module power supply voltage is too low. • (5) •
C1061 Pump motor and/or motor circuit failure Defective pump motor and/or motor power supply voltage is too low. • - •
C1063 Solenoid valve power supply driver circuit failure Mismatching solenoid output and solenoid monitor is detected. • • •
C1065 (6) Brake light relay circuit failure The operated no condition of brake light does not correspond to the operating conditions of brake light switch and brake light relay for specified time. - - -
C1071 ESP® control module internal defect ESP® control module internal defect is detected. • • •
C1073 Lost communication with yaw rate/G sensor assembly CAN line communication error in ESP® control module and yaw rate/G sensor assembly is detected. (2) - •
C1075 Steering angle sensor calibration incomplete (4) Missing steering angle sensor calibration point data is detected. - - -
C1076 Master cylinder pressure sensor calibration incomplete Master cylinder pressure sensor calibration is incompleted. - - •
C1077 Longitudinal G sensor in yaw rate/G sensor assembly calibration incomplete Longitudinal G sensor in yaw rate/G sensor assembly calibration is incompleted. (for 4WD vehicle) • - •
C1078 Lateral G sensor in yaw rate/G sensor assembly calibration incomplete Lateral G sensor in yaw rate/G sensor assembly calibration is incompleted. - - •
C1079 Steering angle sensor calibration failure The calibration for steering angle sensor can not be performed. - - •
C1090 ECM detect rolling counter failure from ESP® control module ESP® control module rolling counter failure is detected by ECM. - - •
C1091 ECM data in CAN line failure ECM sent invalid signal to ESP® control module. - - •
C1092 TCM data in CAN line failure TCM sent invalid signal to ESP® control module. (for A/T model)
C1093 4WD control module data in CAN line failure 4WD control module sent invalid signal to ESP® control module. (if equipped 4WD control module)
C1094 Torque request reject status ECM sent invalid signal of torque control to ESP® control module. - - •
U0073 Control module communication bus off Transmission error that is inconsistent between transmission data and transmission monitor (CAN bus monitor) data is detected more than 7 times continuously. - - •
U0100 Lost communication with ECM (reception error) ECM message data is missing from CAN communication. - - •
U0101 Lost communication with TCM (reception error) TCM message data is missing from CAN communication. (for A/T model)
U0114 Lost communication with 4WD control module (reception error) 4WD control module message data is missing from CAN communication. (if equipped 4WD control module)
U0126 Lost communication with steering angle sensor (reception error) Steering angle sensor message data is missing from CAN communication.
U0140 Lost communication with BCM (reception error) BCM message data is missing from CAN communication.
"•" in ABS warning light, EBD warning light and ESP® warning light columns of the above table means warning light is lit when DTC is detected.
(1) If two or more wheel speed sensor are defective, ABS warning light, EBD warning light and ESP® warning light are lit and all the control functions are deactivated. If one wheel speed sensor is defective, ABS warning light and ESP® warning light are lit and ABS and traction control system/stability control system are deactivated.
(2) For 4WD vehicle, ABS warning light and ESP® warning light are lit and ABS and traction control system/stability control system are deactivated. For 2WD vehicle, ESP® warning light is lit and traction control system/stability control system is deactivated.
(3) SLIP indicator light, ESP® OFF light and hill descent control indicator light (if equipped) turn ON when power supply circuit voltage is low.
(4) SLIP indicator light flashes continuously at Intervals of 1 Hz.
(5) EBD warning light is lit when power supply circuit voltage is too low.
(6) For hill descent control model.
scientia non olet · About LEMON Manuals