DTC Table

WARNING: This page is about a different variant/trim than selected.

NOTE:

With the CAN communication OBD generic scan tool, DTC No. With delta (Δ) mark in the following table can not be read.
For details of D/C (driving cycle), refer to ON-BOARD DIAGNOSTIC SYSTEM DESCRIPTION .

DTC CHART

DTC No.	Detecting Item	Detecting Condition (DTC will set when detecting)	DTC	MIL
DTC P0602/P1702: Control Module Programming Error/Internal Control Module Memory Check Sum Error P0602	Control Module Programming Error	Data programming error.	1 D/C	Not applicable
DTC P0705: Transmission Range Sensor Circuit Malfunction P0705	Transmission Range Sensor Circuit Malfunction (PRNDL Input)	Multiple signals are inputted simultaneously.	1 D/C	1 D/C
DTC P0707: Transmission Range Sensor Circuit Low P0707	Transmission Range Sensor Circuit Low	No sensor signal is inputted.	2 D/C	2 D/C
DTC P0711 P0711	Transmission Fluid Temperature Sensor "A" Circuit Range/Performance	Transmission fluid temperature sensor variation is less than specified value even though engine was running for specified time after engine start.	2 D/C	2 D/C
DTC P0712 P0712	Transmission Fluid Temperature Sensor "A" Circuit Low	Sensor output voltage is too low.	2 D/C	2 D/C
DTC P0713 P0713	Transmission Fluid Temperature Sensor "A" Circuit High	Sensor output voltage is too high.	2 D/C	2 D/C
DTC P0717 P0717	Input/Turbine Speed Sensor "A" Circuit No Signal	No sensor signal is detected although output speed sensor signal is inputted.	1 D/C	1 D/C
DTC P0722 P0722	Output Speed Sensor Circuit No Signal	No sensor signal is inputted although input speed sensor signal is inputted.	1 D/C	1 D/C
DTC P0741/P0742 P0741	Torque Converter Clutch Circuit Performance or Stuck Off	Difference in revolution between engine and input shaft is too large although TCM is commanding TCC pressure control solenoid to turn ON.	2 D/C	2 D/C
DTC P0741/P0742 P0742	Torque Converter Clutch Circuit Stuck On	Difference in revolution between engine and input shaft is too small although TCM is commanding TCC pressure control solenoid to turn OFF.	2 D/C	2 D/C
DTC P0751/P0752 P0751	Shift Solenoid "A" Performance or Stuck Off	The gear commanded by TCM does not match the actual gear when driving.	2 D/C	2 D/C
DTC P0751/P0752 P0752	Shift Solenoid "A" Stuck On	The gear commanded by TCM does not match the actual gear when driving.	2 D/C	2 D/C
DTC P0756/P0757 P0756	Shift Solenoid "B" Performance or Stuck Off	The gear commanded by TCM does not match the actual gear when driving.	2 D/C	2 D/C
DTC P0756/P0757 P0757	Shift Solenoid "B" Stuck On	The gear commanded by TCM does not match the actual gear when driving.	2 D/C	2 D/C
DTC P0771/P0772 P0771	Shift Solenoid "E" Performance or Stuck Off	The gear commanded by TCM does not match the actual gear when driving.	2 D/C	2 D/C
DTC P0771/P0772 P0772	Shift Solenoid "E" Stuck On	The gear commanded by TCM does not match the actual gear when driving.	2 D/C	2 D/C
DTC P0781 P0781	1-2 Shift	The gear commanded by TCM does not match the actual gear when driving.	2 D/C	2 D/C
DTC P0797 P0797	Pressure Control Solenoid "C" Stuck On	The gear commanded by TCM does not match the actual gear when driving.	2 D/C	2 D/C
DTC P0961/P0965/P0969 P0961	Pressure Control Solenoid "A" Control Circuit Range/Performance	Difference between target current of control solenoid circuit and monitor current of control solenoid circuit is more than specified.	1 D/C	1 D/C
DTC P0962/P0966/P0970 P0962	Pressure Control Solenoid "A" Control Circuit Low	No electric flow is detected on pressure control solenoid circuit.	1 D/C	1 D/C
DTC P0963/P0967/P0971 P0963	Pressure Control Solenoid "A"	Control Circuit High Too much electric flow is detected on pressure control solenoid circuit.	1 D/C	1 D/C
DTC P0961/P0965/P0969 P0965	Pressure Control Solenoid "B" Control Circuit Range/Performance	Difference between target current of control solenoid circuit and monitor current of control solenoid circuit is more than specified.	1 D/C	1 D/C
DTC P0962/P0966/P0970 P0966	Pressure Control Solenoid "B" Control Circuit Low	No electric flow is detected on pressure control solenoid circuit.	1 D/C	1 D/C
DTC P0963/P0967/P0971 P0967	Pressure Control Solenoid "B" Control Circuit High	Too much electric flow is detected on pressure control solenoid circuit.	1 D/C	1 D/C
DTC P0961/P0965/P0969 P0969	Pressure Control Solenoid "C" Control Circuit Range/Performance	Difference between target current of control solenoid circuit and monitor current of control solenoid circuit is more than specified.	1 D/C	1 D/C
DTC P0962/P0966/P0970 P0970	Pressure Control Solenoid "C" Control Circuit Low	No electric flow is detected on pressure control solenoid circuit.	1 D/C	1 D/C
DTC P0963/P0967/P0971 P0971	Pressure Control Solenoid "C" Control Circuit High	Too much electric flow is detected on pressure control solenoid circuit.	1 D/C	1 D/C
DTC P0973/P0976/P0985 P0973	Shift Solenoid "A" Control Circuit Low	Voltage of shift solenoid terminal is low although TCM is commanding shift solenoid to turn ON.	1 D/C	1 D/C
DTC P0974/P0977/P0986 P0974	Shift Solenoid "A" Control Circuit High	Voltage of shift solenoid terminal is high although TCM is commanding shift solenoid to turn OFF.	1 D/C	1 D/C
DTC P0973/P0976/P0985 P0976	Shift Solenoid "B" Control Circuit Low	Voltage of shift solenoid terminal is low although TCM is commanding shift solenoid to turn ON.	1 D/C	1 D/C
DTC P0974/P0977/P0986 P0977	Shift Solenoid "B" Control Circuit High	Voltage of shift solenoid terminal is high although TCM is commanding shift solenoid to turn OFF.	1 D/C	1 D/C
DTC P0973/P0976/P0985 P0985	Shift Solenoid "E" Control Circuit Low	Voltage of shift solenoid terminal is low although TCM is commanding shift solenoid to turn ON.	1 D/C	1 D/C
DTC P0974/P0977/P0986 P0986	Shift Solenoid "E" Control Circuit High	Voltage of shift solenoid terminal is high although TCM is commanding shift solenoid to turn OFF.	1 D/C	1 D/C
DTC P0602/P1702 P1702	Internal Control Module Memory Check Sum Error	Calculation of current data stored in TCM is not correct comparing with pre-stored checking data in TCM.	1 D/C	1 D/C
DTC P1706 P1706	Torque Request Communication Error from TCM	ECM detects abnormality of CAN communication data which TCM transmits.	1 D/C	Not applicable
DTC P1723 P1723	Range Select Switch Malfunction	"4" position switch signal is inputted out of specified value.	1 D/C	1 D/C
DTC P1874 P1874	4WD Low Switch Circuit Malfunction (Short)	Actual transfer position is 4H although transfer low signal is inputted. (if equipped with 4L/N switch)	1 D/C	1 D/C
DTC P1875 P1875	4WD Low Switch Circuit Malfunction (Open)	Actual transfer position is 4L although transfer low signal is not inputted. (if equipped with 4L/N switch)	1 D/C	1 D/C
DTC P1878 P1878	Torque Converter Clutch Shudder	Variation in the output revolution speed of the specified amplitude and specified cycle is detected under slip look-up condition.	20 D/C	Not applicable
DTC P2762 P2762	Torque Converter Clutch Pressure Control Solenoid Control Circuit Range/Performance	Difference between target current of TCC solenoid valve circuit and monitor current of TCC solenoid valve circuit is more than specified value.	1 D/C	1 D/C
DTC P2763 P2763	Torque Converter Clutch Pressure Control Solenoid Control Circuit High	Too much electric flow is detected on TCC pressure control solenoid circuit.	1 D/C	1 D/C
DTC P2764 P2764	Torque Converter Clutch Pressure Control Solenoid Control Circuit Low	No electric flow is detected on TCC pressure control solenoid circuit.	1 D/C	1 D/C
U0073	Control Module Communication Bus Off	Refer to CAN DTC (LOST COMMUNICATION AND COMMUNICATION BUS OFF) TABLE .	1 D/C	1 D/C
DTC U0100: LOST COMMUNICATION WITH ECM/PCM "A" U0100	Lost Communication With ECM		1 D/C	1 D/C
DTC U0140 U0140	Lost Communication With BCM		1 D/C	Not applicable