LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Suzuki >> 2007 >> Swift + >> Repair and Diagnosis >> Transmission >> Manual Trans >> Manual Transaxle - Y4M >> Specifications >> Manual Transmission Specifications
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Manual Transmission Specifications

General Specifications

Application Specification
Metric English
General
  • Type - Forward Gear
 Synchronized Mesh Type
  • Type - Reverse Gear
 Sliding Mesh Type
  • Gear Ratio - 1st
 3.417
  • Gear Ratio - 2nd
 1.950
  • Gear Ratio - 3rd
 1.280
  • Gear Ratio - 4th
 0.971
  • Gear Ratio - 5th
 0.758
  • Gear Ratio - Reverse
 3.273
  • Final Drive Ratio
 4.105
  • Fluid Capacity
 2.1 L 2.21 qt
  • Fluid Classification
 75W-85 GL-4
Service
  • Clearance Between Gear and Synchronizer Ring - Limit
 0.5 mm 0.020 in
  • Clearance Between Gear and Synchronizer Ring - Standard
 1.0 mm 0.039 in
  • Clearance Between Sleeve and Shift Fork - Limit
 1.0 mm 0.039 in
  • Clearance Between Sleeve and Shift Fork - Standard
 0.2-0.6 mm 0.008-0.024 in
  • Key Groove Width of Synchronizer Ring - Limit - 1st Gear
 10.0 mm 0.394 in
  • Key Groove Width of Synchronizer Ring - Standard - 1st Gear
 9.6 mm 0.378 in
  • Key Groove Width of Synchronizer Ring - Limit - 2nd, 3rd, 4th Gear
 10 mm 0.394 in
  • Key Groove Width of Synchronizer Ring - Standard - 2nd, 3rd, 4th Gear
 9.6 mm 0.378 in
  • Key Groove Width of Synchronizer Ring - Limit - 5th Gear
 9.8 mm 0.386 in
  • Key Groove Width of Synchronizer Ring - Standard - 5th Gear
 9.4 mm 0.370 in
  • Shift Fork End Thickness for Low Speed Shift Fork - Limit - 1st-2nd Gear
 8.1 mm 0.319 in
  • Shift Fork End Thickness for Low Speed Shift Fork - Standard - 1st-2nd Gear
 8.7 mm 0.343 in
  • Shift Fork End Thickness for Low Speed Shift Fork - Limit - 3rd-4th Gear
 7.2 mm 0.283 in
  • Shift Fork End Thickness for High Speed Shift Fork - Standard - 3rd-4th Gear
 7.8 mm 0.307 in
  • Shift Fork End Thickness for Low Speed Shift Fork - Limit - 5th Gear
 7.2 mm 0.283 in
  • Shift Fork End Thickness for Shift Fork - Standard - 5th Gear
 7.8 mm 0.307 in
  • Speedometer Gear Ratio - Driven/Drive
 17/18 0.944
  • Thrust Free Play of Differential Side Gear
 0.05-0.33 mm 0.002-0.013 in
Performance - Manual Transmission

Application Specification
Metric English
Gradeability 0.4 (tan O)
Maximum Speed 153 km/h 95.1 mph
Minimum Turning Radius 4.8 m 15.7 ft
Manual Transmission

Application Specification
Metric English
Final Drive Ratio 4.105:1
Gear Ratio
  • 1st
 3.417:1
  • 2nd
 1.950:1
  • 3rd
 1.280:1
  • 4th
 0.971:1
  • 5th
 0.758:1
  • Reverse
 3.273:1
Maker DWMC
Oil Capacity 2.1 L 2.22 qt
Type or Model Y4M
Transaxle Case Surface and Bearing Outer Races Clearance Table

Measured value Shim thickness
0.33-0.37 mm (0.0130-0.0146 in) 0.45 mm (0.0177 in)
0.38-0.42 mm (0.0147-0.0165 in) 0.50 mm (0.0197 in)
0.43-0.47 mm (0.0169-0.0185 in) 0.55 mm (0.0217 in)
0.48-0.52 mm (0.0189-0.0205 in) 0.60 mm (0.0236 in)
0.53-0.57 mm (0.0209-0.0224 in) 0.65 mm (0.0256 in)
0.58-0.62 mm (0.0228-0.0244 in) 0.70 mm (0.0276 in)
0.63-0.67 mm (0.0248-0.0264 in) 0.75 mm (0.0295 in)
0.68-0.72 mm (0.0268-0.0283 in) 0.80 mm (0.0315 in)
0.73-0.77 mm (0.0287- 0.0303 in) 0.85 mm (0.0335 in)
0.78-0.82 mm (0.0307-0.0323 in) 0.90 mm (0.0354 in)
0.83-0.87 mm (0.0327-0.0343 in) 0.90 mm (0.0354 in)
0.88-0.92 mm (0.0346-0.0362 in) 1.00 mm (0.0394 in)
0.93-0.97 mm (0.0366-0.0382 in) 1.05 mm (0.0413 in)
0.98-1.02 mm (0.0386-0.0402 in) 1.10 mm (0.0433 in)
1.03-1.07 mm (0.0406-0.0421 in) 1.15 mm (0.0453 in)
Side Gear Axle Direction Play Table

Application Specification
Metric English
Thrust Adjusting Shim 0.90-0.95 mm 0.0354-0.0374 in
1.00-1.05 mm 0.0394-0.0413 in
1.10-1.15 mm 0.0433-0.0453 in
1.20 mm 0.0472 in
Thrust Free Play of Differential Side 0.05-0.33 mm 0.0020-0.0130 in
scientia non olet · About LEMON Manuals