Engine Specifications
WARNING: This page is about a different car, the 2006 Suzuki Verona. However, it is still accessible from the selected car via links, so may be relevant.
ENGINE SPECIFICATIONS
| Application | Description | |
|---|---|---|
| General Data: | ||
| Engine Type | 6 Cylinder (In-Line) | |
| Displacement | 2,492 cm3 (152 in3 ) | |
| Bore Stroke | 77 x 89.2 mm (3.03 x 3.51 in.) | |
| Compression Ratio | 9.8 : 1 | |
| Firing Order | 1-5-3-6-2-4 | |
| Cylinder Bore: | ||
| Diameter | 76.994 - 77.006 mm (3.0313 - 3.0317 in.) | |
| Out of Round (Maximum) | 0.007 mm (0.00028 in.) | |
| Cylinder Bore Taper (Maximum) | 0.01 mm (0.0004 in.) | |
| Piston Protrusion | -0.457 - 0.132 mm (-0.01799 - 0.00520 in.) | |
| Oversize (Measure Replacement Piston before Re-boring) | None | |
| Block Face Distortion | 0.007 mm (0.0003 in.) | |
| Piston: | ||
| Diameter | 76.973 - 77.015 mm (3.0304 - 3.0320 in.) | |
| Clearance to Bore | -0.015 - 0.027 mm (-0.00059 - 0.001063 in.) | |
| Ring Groove Width | Top | 1.23 - 1.25 mm (0.0484 - 0.0492 in.) |
| 2nd | 1.50 - 1.52 mm (0.0590 - 0.0598 in.) | |
| Oil | 2.01 - 2.03 mm (0.0791 - 0.0799 in.) | |
| Ring Grove Inner Diameter | Top | 69.3 - 69.5 mm (2.7283 - 2.7362 in.) |
| 2nd | 68.7 - 68.9 mm (27047 - 2.7125 in.) | |
| Oil | 68.2 - 68.4 mm (2.6850 - 2.6929 in.) | |
| Piston Rings: | ||
| Ring, End Gap, Top Compression | 0.2 - 0.35 mm (0.00787 - 0.01378 in.) | |
| Ring, End Gap, Second Compression | 0.35 - 0.5 mm (0.01378 - 0.01969 in.) | |
| Oil | 0.2 - 0.7 mm (0.00787 - 0.02756 in.) | |
| Piston Ring Width | Top | 1.170 - 1.190 mm (0.0460 - 0.0468 in.) |
| 2nd | 1.470 - 1.490 mm (0.0578 - 0.0586 in.) | |
| Oil | 1.88 - 1.95 mm (0.0740 - 0.0767 in.) | |
| Piston Ring Thickness | Top | 2.75 - 3.05 mm (0.1082 - 0.1200 in.) |
| 2nd | 3.05 - 3.35 mm (0.1200 - 0.1318 in.) | |
| Oil | 2.90 - 3.10 mm (0.1141 - 0.1220 in.) | |
| Ring Groove Clearance | Top | 0.04 - 0.08 mm (0.00157 - 0.00314 in.) |
| 2nd | 0.01 - 0.05 mm (0.00039 - 0.00196 in.) | |
| Oil | 0.06 - 0.15 mm (0.00236 - 0.00590 in.) | |
| Piston Pin: | ||
| Diameter | 18.995 - 19.000 mm (0.74783 - 0.74803 in.) | |
| Pin Offset | 0.6 mm (0.02362 in.) | |
| Clearance: In Piston | 0.009 - 0.019 mm (0.00035 - 0.00075 in.) | |
| Clearance: In Rod | Interference Fit in Rod (-0.010 - 0.025 mm) | |
| Length | 55.7 - 56.0 mm (2.193 - 2.205 in.) | |
| Camshaft: | ||
| Lift - Intake | 10 mm (0.39 in.) | |
| Lift - Exhaust | 9 mm (0.35 in.) | |
| Camshaft Cap to Bearing Journal Clearance | 0.03 - 0.071 mm (0.00118 - 0.00280 in.) | |
| Bearing Journal OD | 24.95 - 24.97 mm (0.98228 - 0.98307 in.) | |
| Crankshaft: | ||
| Main Journal-Diameter (All) | 57.980 - 58.000 mm (2.2827 - 2.2835 in.) | |
| Main Journal - Radial Run out (Shaft Support on No. 1 and No. 7 Bearings Measured at No. 4 Journal) | 0.06 mm (0.00236 in.) | |
| Main Bearing Clearance (All) | 0.019 - 0.049 mm (0.00075 - 0.000193 in.) | |
| End Play | 0.055 - 0.265 mm (0.002 - 0.010 in.) | |
| Service Oversize, Available in 2 sizes | Not Necessary | |
| Connecting Rod Journal: | ||
| Diameter (All) | 47.2 - 47.212 mm (1.8583 - 1.8587 in.) | |
| Out of Round (Maximum) | 0.008 mm (0.00031 in) | |
| Rod Bearing Play | 0.080 - 0.260 mm (0.00315 - 0.01024 in.) | |
| Rod Bearing Clearance | 0.031 - 0.065 mm (0.00122 - 0.00256 in.) | |
| Cylinder Head: | ||
| Valve Stem Protrusion | 27 mm (1.063 in.) | |
| Valve Guide Height | 11.7 - 12.0 mm (0.46063 - 0.47244 in.) | |
| Overall Height | 128.2 - 128.4 mm (5.04724 - 5.05512 in.) | |
| Minimum Overall Height After Machining | 128.1 mm (5.04331 in.) | |
| Valve System: | ||
| Valve Lash Compensators | Hydraulic | |
| Seat Run Out (Maximum, All) | 0.05 mm (0.00197 in.) | |
| Face Run Out (Maximum, All) | 0.03 mm (0.00118 in.) | |
| Valve Stem Diameter Intake | 5.465 - 5.479 mm (0.21516 - 0.21571 in.) | |
| Valve Stem Diameter Exhaust | 5.465 - 5.470 mm (0.21480 - 0.21535 in.) | |
| Valve Diameter Intake | 30.1 - 30.3 mm (1.18504 - 1.19291 in.) | |
| Valve Diameter Exhaust | 25.7 - 25.9 mm (1.01181 - 1.01969 in.) | |
| Valve Seat Width Intake | 1.0 - 1.4 mm (0.03937 - 0.05512 in.) | |
| Valve Seat Width Exhaust | 1.4 - 1.8 mm (0.05512 - 0.07087 in.) | |
| Valve Face Angle | 90° - 90° 40' | |
| Valve Seat Angle | 89.5° - 90° | |
| Valve Guide Inside Diameter | 5.5 - 5.512 mm (0.21654 - 0.21701 in.) | |
| Oil Pump: | ||
| Outer Gear to Body | 0.1 - 0.19 mm (0.00394 - 0.00748 in.) | |
| Outer Gear to Crescent | 0.02 - 0.07 mm (0.00079 - 0.00276 in.) | |
| Inner Gear to Crescent | 0.02 - 0.07 mm (0.00079 - 0.00276 in.) | |
| End Clearance (TIP clearance) | 0.02 - 0.16 mm (0.00079 - 0.00630 in.) | |
| Sealants and Adhesives: | ||
| Oil Pan Bolts (Oil pan x Bed plate) | Loctite® 5900 | |
| Oil Gallery Plug | Loctite® 242 | |
| Coolant Jacket Caps and Plugs (Freeze Plugs) | Dry seal-lock coated in plug | |