Tightening Torque Specifications
WARNING: This page is about a different car, the 2008 Suzuki Grand Vitara, 2007 Suzuki Grand Vitara, and 2006 Suzuki Grand Vitara. However, it is still accessible from the selected car via links, so may be relevant.
TIGHTENING TORQUE SPECIFICATIONS
| Fastening part | Tightening torque | ||
|---|---|---|---|
| N.m | kgf-m | lb-ft | |
| Camshaft housing bolts | 11 N.m (1.1 kgf-m, 7.5 lb-ft) by the specified procedure | ||
| Camshaft housing bolt | 11 | 1.1 | 8.0 |
| Cylinder head cover nut | 10.5 | 1.1 | 7.5 |
| Engine block heater mounting bolt | 11 | 1.1 | 8.0 |
| Timing chain cover bolt | 11 | 1.1 | 8.0 |
| Crankshaft pulley bolt | 150 | 15 | 108.5 |
| Timing chain guide No.4 bolt | 11 | 1.1 | 8.0 |
| Camshaft timing sprocket bolt | 80 | 8.0 | 58.0 |
| Timing chain tensioner adjuster No.3 bolt | Tighten 11 N.m (1.1 kgf-m, 7.5 lb-ft) by the specified procedure | ||
| Timing chain tensioner adjuster No.3 nut | Tighten 45 N.m (4.5 kgf-m, 32.5 lb-ft) by the specified procedure | ||
| RH (No.2) bank 1st timing chain intake camshaft sprocket bolt | 80 | 8.0 | 58.0 |
| Timing chain tensioner nut | 25 | 2.5 | 18.0 |
| Idler sprocket No.1 bolt | 55 | 5.5 | 40.0 |
| Timing chain tensioner adjuster No.1 bolt | 11 | 1.1 | 8.0 |
| Timing chain guide No.1 and No.2 bolt | 9 | 0.9 | 6.5 |
| Timing chain tensioner adjuster No.2 bolt | 11 | 1.1 | 8.0 |
| Camshaft housing bolt | 11 N.m (1.1 kgf-m, 8.0 lb-ft) by the specified procedure | ||
| Timing chain guide No.3 bolt | 11 | 1.1 | 8.0 |
| Cylinder head bolt | Tighten 53 N.m (5.3 kgf-m, 38.5 lb-ft), 84 N.m (8.4 kgf-m, 61.0 lb-ft), 0 N.m (0 kgf-m, 0 lb-ft), 53 N.m (5.3 kgf-m, 38.5 lb-ft) and 105 N.m (10.5 kgf-m, 76.0 lb-ft) by the specified procedure | ||
| Cylinder head bolt (hex hole bolt) | Tighten 11 N.m (1.1 kgf-m, 7.5 lb-ft) by the specified procedure | ||
| Connecting rod bolt | Tighten 15 N.m (1.5 kgf-m,11.0 lb-ft), 45° and 45° by the specified procedure. | ||
| Lower crankcase bolt (10 mm (0.39 in.) thread diameter) | Tighten 30 N.m (3.0 kgf-m,22.0 lb-ft), 0 N.m (0 kgf-m, 0 lb-ft), 42 N.m (4.2 kgf-m, 30.5 lb-ft) and 40° by the specified procedure | ||
| Lower crankcase bolt (8 mm (0.31 in.) thread diameter) | 27 N.m (2.7 kgf-m,19.5 lb-ft) by the specified procedure | ||
| Flywheel (or drive plate) bolt | 70 | 7.0 | 51.0 |