LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Suzuki >> 2006 >> Grand Vitara Premium, RWD, Standard >> Repair and Diagnosis >> Engine Performance >> System >> Engine General Information And Diagnosis >> Diagnostic Information And Procedures >> DTC P2098/P2099: Post Catalyst Fuel Trim System Too Lean/Too Rich (Sensor-2, Bank-2) >> DTC Troubleshooting
April 5, 2026: LEMON Manuals is launched! Read the announcement.

DTC Troubleshooting

NOTE: Before this trouble shooting is performed, read the precautions for DTC troubleshooting referring to PRECAUTIONS FOR DTC TROUBLESHOOTING .
DTC TROUBLESHOOTING CHART

Step Action YES NO
1  Was "Engine and Emission Control System Check" performed?  Go to Step 2. Go to ENGINE AND EMISSION CONTROL SYSTEM CHECK .
2  HO2S signal check 
  1. Connect scan tool with ignition switch turned OFF.
  2. Warm up engine to normal operating temperature and keep it at 2000 r/min. for 60 sec.
  3. Repeat racing engine (Repeat depressing accelerator pedal 5 to 6 times continuously to enrich A/F mixture and take foot off from pedal to enlean it).
  4. Check for HO2S (bank-2) output voltage displayed on scan tool.

Does HO2S output voltage between 0.5 V and 0.8 V? 		 Intermittent trouble. Check for intermittent referring to INTERMITTENT AND POOR CONNECTION INSPECTION . Go to Step 3.
3  Intake system and exhaust system for leakage check 
  1. Check intake system and exhaust system for leakage.

Are intake system and exhaust system in good condition? 		 Go to Step 4. Repair or replace defective parts.
4  Fuel injectors and its circuit check 
  1. Check each bank-2 fuel injectors referring to FUEL INJECTOR INSPECTION .

Is check result satisfactory? 		 Go to Step 5. Faulty injector(s) or its circuit.
5  HO2S circuit check 
  1. Disconnect connector from HO2S (bank-2) and ECM with ignition switch turned OFF.
  2. Check for proper terminal connection to HO2S (bank-2) connector and ECM connector.
  3. If connections are OK, check that HO2S (bank-2) circuit is as follows.
    • Wiring harness resistance of each "Signal circuit of HO2S (bank-2)", "Ground circuit of HO2S (bank-2)" and "Control circuit of HO2S (bank-2) heater" is less than 1 Ω.
    • Insulation resistance between "Signal circuit of HO2S (bank-2)" and vehicle body ground is infinity.
    • Insulation resistance of wire harness is infinity between "Signal circuit of HO2S (bank-2)" terminal each other terminal at "Signal circuit of HO2S (bank-2)" connector.
    • Circuit voltage between "Signal circuit of HO2S (bank-2)" and vehicle body ground is 0 V with ignition switch turned ON.

Are they in good condition? 		 Go to Step 6. Repair or replace defective wiring harness.
6  HO2S heater check 
  1. Check heater resistance of HO2S (bank-2) referring to HEATED OXYGEN SENSOR (HO2S-2) HEATER ON-VEHICLE INSPECTION .

Is HO2S heater in good condition? 		 Go to Step 7. Replace HO2S (bank-2).
7  A/F sensor circuit check 
  1. Disconnect connector from A/F sensor (bank-2) with ignition switch turned OFF.
  2. Check for proper terminal connection to A/F sensor (bank-2) connector and ECM connector.
  3. If connections are OK, check that A/F sensor (bank-2) circuit is as follows.
    • Wiring harness resistance of each "Signal (+) circuit of A/F sensor (bank-2)", "Signal (-) circuit of A/F sensor (bank-2)", "Control circuit of A/F sensor (bank-2) heater" and "Control ground circuit of A/F sensor (bank-2) heater" is less than 1 Ω.

Is it in good condition? 		 Go to Step 5. Repair or replace defective wiring harness.
8  A/F sensor adjusting resistor circuit check 
  1. Check that A/F sensor (bank-2) adjusting resistor circuit is as follows.
    • Wiring harness resistance of each "Adjusting resistor (+) circuit of A/F sensor (bank-2)" and "Adjusting resistor (-) circuit of A/F sensor (bank-2)" is less than 1 Ω.
    • Insulation resistance between "Adjusting resistor (+) circuit of A/F sensor (bank-2)" and vehicle body ground is infinity.
    • Insulation resistance between "Adjusting resistor (+) circuit of A/F sensor (bank-2)" and "Adjusting resistor (-) circuit of A/F sensor (bank-2)" is infinity.
    • Circuit voltage between "Adjusting resistor (+) circuit of A/F sensor (bank-2)" and vehicle body ground is 0 V with ignition switch tuned ON.

Are they in good condition? 		 Go to Step 6. Repair or replace defective wiring harness.
9  A/F sensor check 
  1. Check for A/F sensor (bank-2) referring to AIR FUEL RATIO (A/F) SENSOR ON-VEHICLE INSPECTION .

Is check result satisfactory? 		 Go to Step 10. Replace A/F sensor (bank-2).
10  Valves and valves clearance check 
  1. Check bank-2 intake & exhaust valve and clearance referring to VALVE LASH (CLEARANCE) INSPECTION and VALVES AND VALVE GUIDES INSPECTION .

Is check result satisfactory? 		 Substitute a known-good HO2S (bank-2) and recheck. If HO2S (bank-2) OK, replace A/F sensor (bank-2). Repair or replace defective parts.
scientia non olet · About LEMON Manuals