Tightening Torque Specifications
TIGHTENING TORQUE SPECIFICATIONS
| Fastening part | Tightening torque | Note | ||
|---|---|---|---|---|
| N.m | kg-m | lb-ft | ||
| Strut tower bar mounting bolts | 50 | 5.0 | 36.5 | / / / |
| Cylinder head cover nut | 10.5 | 1.1 | 7.5 | |
| Timing chain cover bolt | 11 | 1.1 | 8.0 | |
| CKP sensor bolt | 6 | 0.6 | 4.5 | |
| Crankshaft pulley bolt | 150 | 15 | 108.5 | |
| Timing chain guide No.4 bolt | 11 | 1.1 | 8.0 | |
| Camshaft timing sprocket bolt | 80 | 8.0 | 58.0 | |
| Timing chain tensioner adjuster No.3 bolt | Tighten 11 N.m (1.1 kg-m, 7.5 lb-ft) by the specified procedure | |||
| Timing chain tensioner adjuster No.3 nut | Tighten 55 N.m (5.5 kg-m, 40.0 lb-ft) by the specified procedure | |||
| RH bank 1st timing chain intake camshaft sprocket bolt | 80 | 8.0 | 58.0 | |
| Timing chain tensioner nut | 27 | 2.7 | 19.5 | |
| Idler sprocket No.1 bolt | 45 | 4.5 | 32.5 | |
| Timing chain tensioner adjuster No.1 bolt | 11 | 1.1 | 8.0 | |
| Timing chain guide No.1 and No.2 bolt | 9 | 0.9 | 6.5 | |
| Timing chain tensioner adjuster No.2 bolt | 11 | 1.1 | 8.0 | |
| Camshaft housing bolt | Tighten 12 N.m (1.2 kg-m, 9.0 lb-ft) by the specified procedure | / | ||
| Timing chain guide No.3 bolt | 11 | 1.1 | 8.0 | |
| Cylinder head bolt | Tighten 53 N.m (5.3 kg-m, 38.5 lb-ft), 84 N.m (8.4 kg-m, 61.0 lb-ft), 0 N.m (0 kg-m, 0 lb-ft), 53 N.m (5.3 kg-m, 38.5 lb-ft) and 105 N.m (10.5 kg-m, 76.0 lb-ft) by the specified procedure | |||
| Cylinder head bolt (hex hole bolt) | Tighten 11 N.m (1.1 kg-m, 7.5 lb-ft) by the specified procedure | |||
| Connecting rod bearing cap nut | 45 | 4.5 | 32.5 | |
| Engine side mounting bracket nut | 55 | 5.5 | 40.0 | |
| Transmission case bolt and nut | 85 | 8.5 | 61.5 | (for M/T vehicle) |
| Transmission case bolt and nut | 80 | 8.0 | 58.0 | (for A/T vehicle) |
| Torque converter bolt | 65 | 6.5 | 47.0 | |
| Exhaust No.1 pipe bolt and nut | 50 | 5.0 | 36.5 | |
| Crankcase bolt | Tighten 42 N.m (4.2 kg-m, 30.5 lb-ft), 0 N.m (0 kg-m, 0 lb-ft), 42 N.m (4.2 kg-m, 30.5 lb-ft) and 60 N.m (6.0 kg-m, 43.5 lb-ft) by the specified procedure | (10 mm (0.39 in.) thread diameter) / / | ||
| Crankcase bolt | Tighten 27 N.m (2.7 kg-m, 19.5 lb-ft) by the specified procedure | (8 mm (0.31 in.) thread diameter) / / | ||
| Flywheel (or drive plate) bolt | 70 | 7.0 | 51.0 | |
| Engine block heater mounting bolt | 11 | 1.1 | 8.0 | |
NOTE:
The specified tightening torque is also described in the following.
"TIMING CHAIN COVER COMPONENTS "
"LH (NO.1) BANK 2ND TIMING CHAIN AND CHAIN TENSIONER COMPONENTS "
"1ST TIMING CHAIN AND CHAIN TENSIONER COMPONENTS "
"RH (NO.2) BANK 2ND TIMING CHAIN AND CHAIN TENSIONER COMPONENTS "
"CAMSHAFTS AND VALVE LASH ADJUSTERS COMPONENTS "
"VALVES AND CYLINDER HEADS COMPONENTS "
"PISTONS, PISTON RINGS, CONNECTING RODS AND CYLINDERS COMPONENTS "
"MAIN BEARINGS, CRANKSHAFT AND CYLINDER BLOCK COMPONENTS "
"TIMING CHAIN COVER COMPONENTS "
"LH (NO.1) BANK 2ND TIMING CHAIN AND CHAIN TENSIONER COMPONENTS "
"1ST TIMING CHAIN AND CHAIN TENSIONER COMPONENTS "
"RH (NO.2) BANK 2ND TIMING CHAIN AND CHAIN TENSIONER COMPONENTS "
"CAMSHAFTS AND VALVE LASH ADJUSTERS COMPONENTS "
"VALVES AND CYLINDER HEADS COMPONENTS "
"PISTONS, PISTON RINGS, CONNECTING RODS AND CYLINDERS COMPONENTS "
"MAIN BEARINGS, CRANKSHAFT AND CYLINDER BLOCK COMPONENTS "
Reference:
For the tightening torque of fastener not specified in this article, refer to "FASTENER INFORMATION ".