LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Suzuki >> 2005 >> Verona EX >> Repair and Diagnosis >> Transmission >> Automatic Transmission >> Diagnostic Information and Procedures >> Internal Wiring Harness Check
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Internal Wiring Harness Check

INTERNAL WIRING HARNESS VALUE CHART

Step Action Value(s) Yes No
1
  1. Disconnect the transaxle harness.
  2. Measure the resistance between terminals 3 and 13 of the transaxle wiring connector.

Is the resistance within the values shown?		 Refer to COMPONENT RESISTANCE CHART . Go to Step 3. Go to Step 2.
2
  1. Disconnect the internal transaxle harness from the first solenoid valve.
  2. Measure the resistance of the first solenoid valve.

Is the resistance within the values shown?		 Refer to COMPONENT RESISTANCE CHART . Go to Step 20. Go to Step 22.
3 Measure the resistance between terminals 3 and 13 the second solenoid valve.
Is the resistance within the values shown?		 Refer to COMPONENT RESISTANCE CHART . Go to Step 5. Go to Step 4.
4
  1. Disconnect the internal transaxle harness from the second solenoid valve.
  2. Measure the resistance of the second solenoid valve.

Is the resistance within the values shown?		 Refer to COMPONENT RESISTANCE CHART . Go to Step 20. Go to Step 22.
5 Measure the resistance between terminals 5 and 6 the transaxle wiring connector (EDS 3).
Is the resistance within the values shown?		 Refer to COMPONENT RESISTANCE CHART . Go to Step 7. Go to Step 6.
6
  1. Disconnect the internal transaxle harness from the pressure control valve 3 (EDS 3).
  2. Measure the resistance of the EDS 3.

Is the resistance within the values shown?		 Refer to COMPONENT RESISTANCE CHART . Go to Step 20. Go to Step 22.
7 Measure the resistance between terminals 5 and 7 the transaxle wiring connector (EDS 4).
Is the resistance within the values shown?		 Refer to COMPONENT RESISTANCE CHART . Go to Step 9. Go to Step 8.
8
  1. Disconnect the internal transaxle harness from the pressure control valve 4 (EDS 4).
  2. Measure the resistance of the EDS 4.

Is the resistance within the values shown?		 Refer to COMPONENT RESISTANCE CHART . Go to Step 20. Go to Step 22.
9 Measure the resistance between terminals 5 and 10 the transaxle wiring connector (EDS 5).
Is the resistance within the values shown?		 Refer to COMPONENT RESISTANCE CHART . Go to Step 11. Go to Step 10.
10
  1. Disconnect the internal transaxle harness from the pressure control valve 5 (EDS 5).
  2. Measure the resistance of the EDS 5.

Is the resistance within the values shown?		 Refer to COMPONENT RESISTANCE CHART . Go to Step 20. Go to Step 22.
11 Measure the resistance between terminals 5 and 11 the transaxle wiring connector (EDS 6).
Is the resistance within the values shown?		 Refer to COMPONENT RESISTANCE CHART . Go to Step 13. Go to Step 12.
12
  1. Disconnect the internal transaxle harness from the pressure control valve 6 (EDS 6).
  2. Measure the resistance of the EDS 6.

Is the resistance within the values shown?		 Refer to COMPONENT RESISTANCE CHART . Go to Step 20. Go to Step 22.
13 Measure the resistance between terminals 4 and 9 the transaxle wiring connector (transaxle temperature sensor).
Is the resistance within the values shown?		 Refer to COMPONENT RESISTANCE CHART . Go to Step 15. Go to Step 14.
14
  1. Disconnect the internal transaxle harness from the transaxle temperature sensor.
  2. Measure the resistance of the transaxle temperature sensor.

Is the resistance within the values shown?		 Refer to COMPONENT RESISTANCE CHART . Go to Step 20. Go to Step 22.
15 Measure the resistance between terminals 15 and 16 the transaxle wiring connector (transaxle input speed sensor).
Is the resistance within the values shown?		 Refer to COMPONENT RESISTANCE CHART . Go to Step 17. Go to Step 16.
16
  1. Disconnect the internal transaxle harness from the transaxle input speed sensor.
  2. Measure the resistance of the input speed sensor.

Is the resistance within the values shown?		 Refer to COMPONENT RESISTANCE CHART . Go to Step 20. Go to Step 22.
17 Measure the resistance between terminals 1 and 2 the transaxle wiring connector (transaxle output speed sensor).
Is the resistance within the values shown?		 Refer to COMPONENT RESISTANCE CHART . Go to Step 19. Go to Step 18.
18
  1. Disconnect the internal transaxle harness from the transaxle output speed sensor.
  2. Measure the resistance of the transaxle output speed sensor.

Is the resistance within the values shown?		 Refer to COMPONENT RESISTANCE CHART . Go to Step 20. Go to Step 22.
19 Measure the resistance between terminals of internal wiring harness.
Is the resistance within the values shown?		 Refer to COMPONENT RESISTANCE CHART . No problem found, exit table Go to Step 21.
20 Inspect for resistance:
  • Inspect the transaxle wiring for poor electrical connections at the transaxle.
  • Look for possible bent, backed out, deformed of damaged terminals.

Check for weak terminal tension.		 - Verify repair and Go to Step 12. No problem found, exit table
21 Replace the internal wiring harness.
Is the replacement complete.		 - No problem found, exit table -
22 Replace the component.
Is the replacement complete.		 - No problem found, exit table -
scientia non olet · About LEMON Manuals