LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Suzuki >> 2004 >> Swift + >> Repair and Diagnosis >> External Pages >> Different car >> Section 19 (Supplemental Inflatable Restraint System) >> Repair Instructions >> SIR Disabling and Enabling Zone 8 >> Disabling Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Disabling Procedure

WARNING: This page is about a different car, the 2005 Suzuki Swift +, 2005 Pontiac Wave, and 2005 Chevrolet Aveo. However, it is still accessible from the selected car via links, so may be relevant.
    Fig 1: Locating Left Side Fuse Block Access Cover
    GM1376168Courtesy of GENERAL MOTORS CORP.
    IMPORTANT: Perform this procedure in order to prevent deployment of the air bags from the reserve energy supply power.
  1. Turn the steering wheel so that the vehicle wheels are pointing straight ahead.
  2. Remove the key from the ignition switch.
    3. IMPORTANT: With the F8 fuse removed and the ignition switch is the ON position, the AIR BAG warning indicator illuminates. This is a normal operation, and does not indicate an SIR system malfunction.
  3. Remove the F8 fuse.
  4. Remove the lower steering column trim panel. Refer to Instrument Panel (I/P) Trim Panel Replacement - Lower in Instrument Panel, Gages, and Console.
  5. Remove the knee bolster.
    6. Fig 2: CPA & Yellow 2-Way Connector For The Inflatable Restraint Steering Wheel Module
    GM1376170Courtesy of GENERAL MOTORS CORP.
  6. Remove the following parts:
    • The connector position assurance (CPA) (2)
    • The yellow 2-way connector for the inflatable restraint steering wheel module (1)-Release then unlock the connector.
    7. Fig 3: Opening Instrument Panel Compartment
    GM467834Courtesy of GENERAL MOTORS CORP.
  7. Remove the glove box. Refer to Storage Compartment Replacement - Instrument Panel (I/P) in Instrument Panel, Gages, and Console.
    8. Fig 4: Connector View
    GM189763Courtesy of GENERAL MOTORS CORP.
  8. Remove the CPA and the yellow 2-way connector from the inflatable restraint I/P module pigtail. Release then unlock the connector.
    9. Fig 5: View Of Seat Belt Pretensioner Connector And Wiring Harness Routing
    GM899818Courtesy of GENERAL MOTORS CORP.
  9. Remove the right lower center pillar trim. Refer to Trim Panel Replacement - Lower Center Pillar in Interior Trim.
  10. Remove the CPA from the seat belt pretensioner - RF connector.
  11. Disconnect the seat belt pretensioner - RF connector from the vehicle harness connector.
  12. Remove the CPA from the side air bag sensor - RF connector.
  13. Disconnect the side air bag sensor - RF connector.
  14. Remove the left lower center pillar trim. Refer to Trim Panel Replacement - Lower Center Pillar in Interior Trim.
  15. Remove the CPA from the seat belt pretensioner - LF connector.
  16. Disconnect the seat belt pretensioner - LF connector from the vehicle harness connector.
  17. Remove the CPA from the side air bag sensor - LF connector.
  18. Disconnect the side air bag sensor - LF connector.
    19. Fig 6: View Of Deployment Harness At Side Impact Module
    GM628320Courtesy of GENERAL MOTORS CORP.
  19. Remove the CPA from the side impact module - LF connector (1) located under the driver seat.
  20. Disconnect the side impact module - LF connector (1).
  21. Remove the CPA from the side impact module - RF connector (1) located under the passenger seat.
  22. Disconnect the side impact module - RF connector (1)
scientia non olet · About LEMON Manuals