P/S Pump Disassembly and Assembly: Assembly

Apply grease to oil seal (1) lip and apply power steering fluid to sliding surface of the shaft (2) then insert pulley's shaft (2) from oil seal side of the pump body.
"A": Grease 99000-25010

Fig 1: Inserting Pulley's Shaft
Courtesy of SUZUKI OF AMERICA CORP.
Apply power steering fluid to O-rings (1) and fit them to pump body.

Fig 2: Applying Power Steering Fluid To O-Rings
Courtesy of SUZUKI OF AMERICA CORP.
Install side plate (1) to pump body.
NOTE: Carefully align the dowel pins on the side plate (1) at bolt hole (2) as shown in the figure.

Fig 3: Installing Side Plate To Pump Body
Courtesy of SUZUKI OF AMERICA CORP.
Apply power steering fluid to sliding surface of rotor (1).
Install rotor (1) to shaft, directing dot (3) marked side of rotor facing up.
Install new snap ring (2) to shaft, then make sure to fit snap into shaft groove securely.
NOTE: Never reuse the removed snap ring (2).

Fig 4: Installing New Snap Ring To Shaft
Courtesy of SUZUKI OF AMERICA CORP.
Apply power steering fluid to sliding surface of cam ring (1).
Install cam ring (1) to pump body. The tapered end of cam ring (1) should face the side plate (2).

Fig 5: Installing Cam Ring To Pump Body
Courtesy of SUZUKI OF AMERICA CORP.
Apply power steering fluid to each vane (2).
Install vanes (2) (10 pieces) to rotor (1).

Fig 6: Installing Vanes To Rotor
Courtesy of SUZUKI OF AMERICA CORP.
Apply power steering fluid to O-ring (1).
Install O-ring (1) to pump body.

Fig 7: Installing O-Ring To Pump Body
Courtesy of SUZUKI OF AMERICA CORP.
Apply power steering fluid to sliding surface of pump cover and rotor.
Match the dowel pins (1) to the holes of the cover plate (2) as shown and install pump cover to pump body.

Fig 8: Matching Dowel Pins To Holes Of Cover Plate
Courtesy of SUZUKI OF AMERICA CORP.
Gradually tighten pump cover (1) bolts to specified torque.
NOTE: After installing pump cover (1), check to make sure that shaft can be turned by hand.

Tightening torque

P/S pump cover bolt (a): 23 N.m (2.3 kg-m, 17.0 lb-ft)

Fig 9: Tightening Power Steering Pump Cover Bolt
Courtesy of SUZUKI OF AMERICA CORP.
Apply power steering fluid to O-ring of pressure switch.
Install pressure switch (1) to pump body.
Tightening torque

Pressure switch (a): 28 N.m (2.8 kg-m, 20.5 lb-ft)

Fig 10: Installing Pressure Switch To Pump Body
Courtesy of SUZUKI OF AMERICA CORP.
Apply power steering fluid to relief valve (flow control valve).
Install relief valve (flow control valve) to pump body.
Install flow control spring.
Apply power steering fluid to O-rings of plug.
Install O-rings to plug.
Tighten plug to specified torque.
Tightening torque

Plug (a): 60 N.m (6.0 kg-m, 43.5 lb-ft)

Fig 11: Tightening Plug
Courtesy of SUZUKI OF AMERICA CORP.
Apply power steering fluid to O-ring (2) of suction connector (1).
Install O-ring (2) to suction connector (1).

Fig 12: Installing O-Ring To Suction Connector
Courtesy of SUZUKI OF AMERICA CORP.
Install suction connector (1) to pump body as shown in the figure.
Tighten suction connector (1) bolts to specified torque.

Tightening torque

Suction connector bolt (a): 10 N.m (1.0 kg-m, 7.5 lb-ft)

Fig 13: Installing Suction Connector To Pump Body
Courtesy of SUZUKI OF AMERICA CORP.