Scan Tool Data Definitions - Anti-lock Brake System

WARNING: This page is about a different car, the 2007 Suzuki XL7. However, it is still accessible from the selected car via links, so may be relevant.

The ABS scan tool data definitions contain a brief description of all ABS related parameters available on the scan tool. The parameters available on the scan tool are listed below in alphanumeric order.

SCAN TOOL DATA DEFINITIONS REFERENCE

ABS Active	The scan tool displays Yes/No. The scan tool displays No when a when not active.
ABS Failed	The scan tool displays On/Off. The scan tool displays On when a when the ABS Failed.
Battery Voltage Signal:	The scan tool will display Voltage depending on the state of the battery and charging system.
Brake Fluid Level Sensor	The scan tool displays OK/Low The scan tool indicates Low when the brake fluid sensor detects fluid lose.
BPP Signal:	The scan tool will display Released/Applied depending on the state of the brake pedal position.
Delivered Torque	The scan tool displays 25-95%. The scan tool displays 25% when the powertrain control module (PCM) is providing the minimum percentage of available torque in an attempt to eliminate wheel slip.
DRP Active	The scan tool will display Yes/No depending on the state of the DRP.
DRP Disabled	The scan tool will display Yes/No depending on the state of the DRP.
Lateral Accelerometer Input	The scan tool displays m/s/2. The lateral accelerometer signal from the lateral accelerometer sensor, roughly 2.5 volts equals 0 g lateral acceleration.
LF Inlet Solenoid Command:	The scan tool displays Active/Inactive. The scan tool displays Active when the left front Outlet solenoid is commanded on.
LF Outlet Solenoid Command:	The scan tool displays Active/Inactive. The scan tool displays Active when the left front Outlet solenoid is commanded on.
LF Wheel Speed Sensor	The scan tool displays 0-327 km/h (0-204 mph). The scan tool displays 0 km/h (0 mph) when the vehicle is not moving or is moving at speeds less than or equal to 0 km/h (0 mph).
Low Tire Press. Lamp	The scan tool displays ON or OFF.
LR Wheel Speed Sensor	The scan tool displays 0-327 km/h (0-204 mph). The scan tool displays 0 km/h (0 mph) when the vehicle is not moving or is moving at speeds less than or equal to 0 km/h (0 mph).
LR Outlet Solenoid Command	The scan tool displays Active/Inactive. The scan tool displays Active when the left front Outlet solenoid is commanded on.
Panic Brake Assist Failed	The scan tool displays No/Yes. The scan tool displays No when the Panic brake Assist functions properly.
Pump Motor Command Voltage	The scan tool displays battery voltage when the pump motor is commanded on.
Requested Torque	The scan tool displays 40-95%. The scan tool displays 40% when the electronic brake control module (EBCM) requests the minimum percentage of available torque in an attempt to eliminate wheel slip.
RF Outlet Solenoid Command	The scan tool displays Active/Inactive. The scan tool displays Active when the right front Outlet solenoid is commanded on.
RF Inlet Solenoid Command	The scan tool displays Active/Inactive. The scan tool displays Active when the right front Inlet solenoid is commanded on.
RF Wheel Speed Sensor	The scan tool displays 0-327 km/h (0-204 mph). The scan tool displays 0 km/h (0 mph) when the vehicle is not moving or is moving at speeds less than or equal to 0 km/h (0 mph).
RR Wheel Speed Sensor	The scan tool displays 0-327 km/h (0-204 mph). The scan tool displays 0 km/h (0 mph) when the vehicle is not moving or is moving at speeds less than or equal to 0 km/h (0 mph).
RR Outlet Solenoid Command	The scan tool displays Active/Inactive. The scan tool displays Active when the right front Inlet solenoid is commanded on.
RR Inlet Solenoid Command	The scan tool displays Active/Inactive. The scan tool displays Active when the right front Inlet solenoid is commanded on.
Steering Wheel Position	The scan tool displays degrees. The steering wheel position signal varies from 720°+ to & 720°-.
Steering Sensor	The scan tool displays centered or uncentered.
TCS Active	The scan tool displays Yes or No. The scan tool displays Yes if the TCS indicator is currently being commanded ON.
TCS Failed	The scan tool displays Yes/No. The scan tool displays Yes when the TCS will not engage caused from a malfunction.
VSES Active	The scan tool displays Yes or No. Indicates if Vehicle Stability Enhancement System (VSES) is currently active.
VSES Failed	The scan tool displays Yes or No. Indicates if the EBCM disabled VSES due to a malfunction.
Yaw Rate Sensor Input	The scan tool displays m/s/2. The yaw rate signal from the yaw rate sensor, roughly 2.5 volts equals 0°/second yaw rate.