LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Suzuki >> 1991 >> Samurai JS >> Repair and Diagnosis >> External Pages >> Different car >> Section 17 (Air Bag System) >> Diagnostic Information and Procedures >> DTC B0014-B0045 >> Circuit/System Testing
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Circuit/System Testing

WARNING: This page is about a different car, the 2007 Suzuki XL7. However, it is still accessible from the selected car via links, so may be relevant.
NOTE: When removing connectors inspect for damage or corrosion. Damage or corrosion in the following requires repair or replacement of the affected component/connector.
  • The pretensioner
  • The air bag module
  • The SDM module
  • The air bag wiring harness connector
  • The SDM wiring harness connector
  1. Ignition OFF, disconnect the harness connector at the applicable air bag module. Refer to the applicable air bag module replacement procedure.
  2. Ignition ON, test for less than 1 volt between the applicable high control circuit terminal and ground.
    • I/P Module - Stage 1 terminal 10
    • I/P Module - Stage 2 terminal 6
    • Left Front Roof Rail Module terminal 13
    • Right Front Roof Rail Module terminal 14
    • Seat Belt Pretensioner - Left terminal 17
    • Seat Belt Pretensioner - Right terminal 18
    • If greater than the specified range, test the circuit for a short to voltage. If the circuit tests normal, replace the SDM.
  3. Test for less than 1 volt between the applicable low control circuit terminal and ground.
    • I/P Module - Stage 1 terminal 11
    • I/P Module - Stage 2 terminal 7
    • Left Front Roof Rail Module terminal 12
    • Right Front Roof Rail Module terminal 15
    • Seat Belt Pretensioner - Left terminal 19
    • Seat Belt Pretensioner - Right terminal 16
    • If greater than the specified range, test the circuit for a short to voltage. If the circuit tests normal, replace the SDM.
  4. Ignition OFF, test for infinite resistance between the applicable high control circuit terminal and ground.
    • I/P Module - Stage 1 terminal 10
    • I/P Module - Stage 2 terminal 6
    • Left Front Roof Rail Module terminal 13
    • Right Front Roof Rail Module terminal 14
    • Seat Belt Pretensioner - Left terminal 17
    • Seat Belt Pretensioner - Right terminal 18
    • If not the specified value, test the circuit for a short to ground. If the circuit tests normal, replace the SDM.
  5. Test for infinite resistance between the applicable low control circuit terminal and ground.
    • I/P Module - Stage 1 terminal 11
    • I/P Module - Stage 2 terminal 7
    • Left Front Roof Rail Module terminal 12
    • Right Front Roof Rail Module terminal 15
    • Seat Belt Pretensioner - Left terminal 19
    • Seat Belt Pretensioner - Right terminal 16
    • If not the specified value, test the circuit for a short to ground. If the circuit tests normal, replace the SDM.
  6. With the applicable adaptor, connect in place of the air bag module.
  7. Ignition ON, verify the DTC is set as current.
    • If DTC is not set or is set as history, replace the applicable air bag module.
  8. Ignition OFF, disconnect and the applicable adaptor.
  9. Disconnect the harness connector at the SDM.
  10. Test for less then 1 ohm of resistance between the following high control circuit terminals.
    • I/P Module - Stage 1 terminal 10
    • I/P Module - Stage 2 terminal 6
    • Left Front Roof Rail Module terminal 13
    • Right Front Roof Rail Module terminal 14
    • Seat Belt Pretensioner - Left terminal 17
    • Seat Belt Pretensioner - Right terminal 18
    • If not within the specified range, test the circuit for an open/high resistance.
  11. Test for less then 1 ohm of resistance between the following low control circuit terminals.
    • I/P Module - Stage 1 terminal 11
    • I/P Module - Stage 2 terminal 7
    • Left Front Roof Rail Module terminal 12
    • Right Front Roof Rail Module terminal 15
    • Seat Belt Pretensioner - Left terminal 19
    • Seat Belt Pretensioner - Right terminal 16
    • If not within the specified range, test the circuit for an open/high resistance.
  12. If all circuits test normal, replace the SDM.
scientia non olet · About LEMON Manuals