Inspection Mode B
WARNING: This page is about a different car, the 2018 Subaru Crosstrek. However, it is still accessible from the selected car via links, so may be relevant.
| DTC | Item | Condition | Number of driving cycles on the detecting condition |
|---|---|---|---|
| P0087 | FUEL RAIL/SYSTEM PRESSURE - TOO LOW BANK 1 | Complete diagnosis with inspection mode A as well. | 1 |
| P0088 | FUEL RAIL/SYSTEM PRESSURE - TOO HIGH BANK 1 | Complete diagnosis with inspection mode A as well. | 1 |
| P0125 | INSUFFICIENT COOLANT TEMPERATURE FOR CLOSED LOOP FUEL CONTROL | [Engine Coolant Temperature] at engine starting: Less than -15°C (5°F) | 2 |
| P0134 | A/F/O2 SENSOR CIRCUIT NO ACTIVITY DETECTED BANK 1 SENSOR 1 | - | 1 |
| P0137 | O2 SENSOR CIRCUIT LOW VOLTAGE BANK 1 SENSOR 2 | - | 2 |
| P0138 | O2 SENSOR CIRCUIT HIGH VOLTAGE BANK 1 SENSOR 2 | - | 2 |
| P0171 | SYSTEM TOO LEAN BANK 1 | Complete diagnosis with inspection mode A as well. | 2 |
| P0172 | SYSTEM TOO RICH BANK 1 | Complete diagnosis with inspection mode A as well. | 2 |
| P0300 | RANDOM/MULTIPLE CYLINDER MISFIRE DETECTED | Complete diagnosis with inspection mode A as well. | 2 |
| P0301 | CYLINDER 1 MISFIRE DETECTED | Complete diagnosis with inspection mode A as well. | 2 |
| P0302 | CYLINDER 2 MISFIRE DETECTED | Complete diagnosis with inspection mode A as well. | 2 |
| P0303 | CYLINDER 3 MISFIRE DETECTED | Complete diagnosis with inspection mode A as well. | 2 |
| P0304 | CYLINDER 4 MISFIRE DETECTED | Complete diagnosis with inspection mode A as well. | 2 |
| P0500 | VEHICLE SPEED SENSOR "A" CIRCUIT | - | 1 |
| P0506 | IDLE CONTROL SYSTEM RPM - LOWER THAN EXPECTED | - | 2 |
| P0507 | IDLE CONTROL SYSTEM RPM - HIGHER THAN EXPECTED | - | 2 |
| P059A | Active Grille Air Shutter "A" Position Sensor Circuit | [Ambient | 1 |
| P059F | Active Grille Air Shutter "A" Performance/Stuck Off | Temperature]: 3 | 2 |
| P05A0 | Active Grille Air Shutter "A" Stuck On | - 33°C (37.4 - 91.4°F) | 2 |
| P05A1 | Active Grille Air Shutter "A" Position Sensor Minimum/Maximum Stop Performance |
2 | |
| P05A2 | Active Grille Air Shutter "A" Control Circuit/Open | 1 | |
| P05A6 | Active Grille Air Shutter "A" Supply Voltage Circuit/Open |
1 | |
| P05C0 | Active Grille Air Shutter Module "A" Over Temperature | 1 | |
| P062D | FUEL INJECTOR DRIVER CIRCUIT PERFORMANCE BANK 1 | - | 1 |
| P0851 | PARK/NEUTRAL SWITCH INPUT CIRCUIT LOW | CVT model | 2 |
| P0852 | PARK/NEUTRAL SWITCH INPUT CIRCUIT HIGH | CVT model | 2 |
| P1261 | CYLINDER 1 DIRECT FUEL INJECTOR CIRCUIT/OPEN | - | 1 |
| P1262 | CYLINDER 2 DIRECT FUEL INJECTOR CIRCUIT/OPEN | - | 1 |
| P1263 | CYLINDER 3 DIRECT FUEL INJECTOR CIRCUIT/OPEN | - | 1 |
| P1264 | CYLINDER 4 DIRECT FUEL INJECTOR CIRCUIT/OPEN | - | 1 |
| P162A | STARTER INTERLOCK INTERNAL CIRCUIT | - | 1 |
| P2096 | POST CATALYST FUEL TRIM SYSTEM TOO LEAN BANK 1 | Complete diagnosis with inspection mode A as well. | 2 |
| P2097 | POST CATALYST FUEL TRIM SYSTEM TOO RICH BANK 1 | Complete diagnosis with inspection mode A as well. | 2 |
WARNING:
When performing inspection mode B on a public road, pay sufficient attention to the traffic condition and give the highest priority to safe driving.
Diagnostic procedure:
- Check that the battery voltage is 12 V or more and fuel remains approx. half [20 - 40 L (5.3 - 10.6 US gal, 4.4 - 8.8 Imp gal)].
- Using the Subaru Select Monitor, clear the memory of [Engine Control System]. Ref. to COMMON (diag)>CLEAR MEMORY .
- Execute the inspection mode. Ref. to ENGINE (DIAGNOSTICS) (H4DO)>INSPECTION MODE .NOTE: Perform the inspection mode after warming up the engine except when the engine coolant temperature at engine start is specified.
- Drive at 10 km/h (6 MPH) or more.
- Stop the vehicle and idle for ten minutes.
- Read the readiness code of [Engine Control System] using Subaru Select Monitor and check that the concerned DTC is completed. Ref. to ENGINE (DIAGNOSTICS) (H4DO)>ALL READINESS DIAGNOSTIC CODE (S) .
- Read the DTC of [Engine Control System] using the Subaru Select Monitor. Ref. to ENGINE (DIAGNOSTICS) (H4DO)>DIAGNOSTIC TROUBLE CODE (DTC) .
- Read the temporary code using the Subaru Select Monitor or general scan tool. Ref. to COMMON (diag)>DIAGNOSTIC TROUBLE CODE (DTC) .