Ignition Control System Tests: SVX

Check ECU Output Signal - Measure voltage between ECU 26-pin Yellow connector terminals and ground. While cranking engine, verify at least 5 volts at each terminal. See ECU OUTPUT SIGNAL table. If at least 5 volts are present, go to next step. If at least 5 volts are not present, inspect ECU connector terminal for damage and/or proper connection. If ECU connector is okay, inspect crankshaft position sensor No. 1 and 2, and camshaft position sensor.

ECU OUTPUT SIGNAL

ECU Terminal No.

Wire Color

Engine Cylinder No.

10 ⁽¹⁾

(BLU Wire)

8 ⁽¹⁾

(BLU/WHT Wire)

9 ⁽¹⁾

(BLU/BLK Wire)

7 ⁽¹⁾

(BLU/RED Wire)

21 ⁽¹⁾

(BLU/YEL Wire)

16 ⁽¹⁾

(BLU/GRN Wire)

⁽¹⁾	Yellow ECU 26-pin connector.

Check Harness Between ECU & Ignitor - Turn ignition off and disconnect ECU and ignitor connectors. Measure harness resistance between ECU 26-pin Yellow connector terminals and ignitor 7-pin Gray connector terminals, and between ignitor connector terminal No. 4 (Black wire) and ground. Refer to the ECU & IGNITOR HARNESS RESISTANCE table. If zero ohms resistance is present, go to next step. If zero ohms resistance is not present, repair harness or connectors as necessary.

ECU & IGNITOR HARNESS RESISTANCE

ECU Terminal No.	Ignitor Terminal No.	Engine Cylinder No.
10 (BLU Wire)	7 (BLU Wire)	1
8 (BLU/WHT Wire)	6 (BLU/WHT Wire)	2
9 (BLU/BLK Wire)	5 (BLU/BLK Wire)	3
7 (BLU/RED Wire)	3 (BLU/RED Wire)	4
21 (BLU/YEL Wire)	2 (BLU/YEL Wire)	5
16 (BLU/GRN Wire)	1 (BLU/GRN Wire)	6

Check Ignitor Output Signal - Connect all connectors. Measure voltage between each ignitor output connector terminal and ground while cranking engine. If at least 5 volts are present, go to next step. If at least 5 volts are not present, replace ignitor.

Check Harness Connector Between Ignitor & Each Ignition Coil - Turn ignition off. Disconnect ignitor 6-pin Gray connector and each ignition coil connector. Verify resistance between ignitor connector terminal and each ignition coil connector terminal. See the IGNITOR & COIL HARNESS RESISTANCE table. If zero ohms resistance is present, go to next step. If zero ohms resistance is not present, repair or replace harness or connectors as necessary.

IGNITOR & COIL HARNESS RESISTANCE

Ignitor Term. No.	Ignition Coil Term. No.	Engine Cylinder No.
1 (GRN/RED Wire)	2 (GRN/RED Wire)	1
2 (GRN/WHT Wire)	2 (GRN/WHT Wire)	2
3 (GRN/BLK Wire)	2 (GRN/BLK Wire)	3
4 (GRN Wire)	2 (GRN Wire)	4
5 (GRN/BLU Wire)	2 (GRN/BLU Wire)	5
6 (GRN/YEL Wire)	2 (GRN/YEL Wire)	6

Check Ignition Coil Power Supply Circuit - Connect all connectors and turn ignition on. Verify 12 volts between each ignition coil connector terminal No. 1 (Black/White wire) and ground. If 12 volts are present, go to next step. If 12 volts are not present, repair harness or connectors as necessary.
Check Ignition System For Spark Using A New Coil - Turn ignition off and remove each ignition coil from cylinder head. Replace each ignition coil with a known good one. Verify a spark occurs at each cylinder. If a spark occurs, see SVX under FUEL PUMP CIRCUIT TESTS . If spark does not occur, replace spark plug(s).