Common Specifications & Procedures
MURANO COMMON SPECIFICATIONS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | SERVICE DATA AND SPECIFICATIONS (SDS) | ||
| Torque | See Torque Specifications in applicable figures under REMOVAL AND INSTALLATION . | ||
| Axle Nut/Hub Bearing Bolts | |||
| Front Axle Nut | 240 N.m (177 Ft. lbs) | ||
| Front Hub Bearing Bolts | 88.3 N.m (65 Ft. lbs) | ||
| Rear Hub Bearing Bolts | 88.3 N.m (65 Ft. lbs) | ||
| Battery | SERVICE DATA AND SPECIFICATIONS (SDS) | ||
| Brakes | |||
| Bleeding Sequence | BLEEDING BRAKE SYSTEM | ||
| Disc Brakes | |||
| Front | FRONT DISC BRAKE |
||
| Rear | REAR DISC BRAKE | ||
| Torque | |||
| Front | See Torque Specifications in applicable figures under FRONT DISC BRAKE . | ||
| Rear | See Torque Specifications in applicable figures under REAR DISC BRAKE . | ||
| Charging | |||
| Alternator | SERVICE DATA AND SPECIFICATIONS (SDS) | ||
| Torque | See Torque Specifications in applicable figures under REMOVAL AND INSTALLATION . | ||
| Drive Belts | |||
| Adjustment | Vehicle equipped with auto tensioner | ||
| Belt Routing | EXPLODED VIEW | ||
| Engine Cooling | |||
| General Service Specifications | SERVICE DATA AND SPECIFICATIONS (SDS) | ||
| Radiator Cap Pressure | 122.3-151.7 kPa (1.2-1.5 kgf/cm2 , 17.7-22 psi) | ||
| Thermostat R & I | WATER INLET AND THERMOSTAT ASSEMBLY | ||
| Water Pump R & I | WATER PUMP | ||
| Engine Mechanical | |||
| Compression | COMPRESSION PRESSURE | ||
| Oil Pressure | |||
| @ Idle | More than 98 kPa (1.0 kg/cm2 , 14 psi) | ||
| Overhaul | SERVICE DATA AND SPECIFICATIONS (SDS) | ||
| Torque | See Torque Specifications in applicable figures under UNIT DISASSEMBLY AND ASSEMBLY . | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate (Drive Plate) Torque | 88 N.m (65 Ft. lbs) | ||
| Fuel System | |||
| Fuel Pressure Release Procedure | FUEL PRESSURE RELEASE | ||
| Fuel Pressure | At idling: Approximately 350 kPa (3.57 kg/cm2 , 51 psi) | ||
| Fuel Pressure Test Procedure | FUEL PRESSURE CHECK | ||
| Fuel Filter Location | In Tank Type | ||
| Fuel Filter R & I | FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Engine has coil-on-plug ignition. | ||
| Ignition Wires (Routing) | Engine has coil-on-plug ignition. | ||
| Spark Plugs | SPARK PLUG Tightening torque: 19.6 N.m (14 Ft. Lbs) |
||
| Starting | |||
| Starter | SERVICE DATA AND SPECIFICATIONS (SDS) | ||
| Torque | See Torque Specifications in applicable figures under REMOVAL AND INSTALLATION . | ||
| Wheel Alignment | |||
| Adjustment Specifications | |||
| Front | WHEEL ALIGNMENT | ||
| Rear | WHEEL ALIGNMENT | ||
| Torque | |||
| Front | See Torque Specifications in applicable figures under REMOVAL AND INSTALLATION . | ||
| Rear | See Torque Specifications in applicable figures under REMOVAL AND INSTALLATION . | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 108 N.m (11 kg.m, 80 Ft. lbs) | ||
| How To Use Nissan Service Information | |||
| Includes: Standard Bolt Torque Symbol Identification General Connector Info |
GENERAL INFORMATION (EXCEPT CROSSCABRIOLET) | ||