Diagnosis Procedure

Perform the self-diagnosis check. Refer to "CONSULT-III FUNCTION (TRANSMISSION) ".

Is any malfunction of the "U1000" indicated in the results? 

YES: Check CAN communication line. Refer to U1000 CAN COMM CIRCUIT .

NO: GO TO 2.

With CONSULT-III 

1. Turn ignition switch ON.
2. Select "ECU INPUT SIGNALS" in "DATA MONITOR" mode for "TRANSMISSION" with CONSULT-III.
3. Read out ON/OFF switching action of the "SPORT MODE SW".
   DIAGNOSIS PROCEDURE
   
   

   Item name	Condition	Display value
   SPORT MODE SW	While pushing overdrive cancel switch	ON
   	Other conditions	OFF

   OK or NG 

   OK: INSPECTION END 

   NG: GO TO 3.

Check overdrive control switch. Refer to "COMPONENT INSPECTION ".

OK or NG 

OK: GO TO 4.

NG: Repair or replace damaged parts.

Perform self-diagnosis check. Refer to "SELF-DIAGNOSIS MODE OF COMBINATION METER ".

Is any malfunction detected by self-diagnostic? 

YES: Check the malfunctioning system.

NO - 1: With Intelligent Key: GO TO 5.

NO - 2: Without Intelligent Key: GO TO  7.

1. Turn ignition switch OFF.
2. Disconnect CVT shift selector connector and combination meter connector.
3. Check continuity between CVT shift selector harness connector (A) terminal and combination meter harness connector (B) terminal.
   CONTINUITY REFERENCE CHART
   
   

   Item	Connector	Terminal	Continuity
   CVT shift selector harness connector	M38	1	Yes
   Combination meter harness connector	M24	29

   Fig 1: Checking Continuity Between CVT Shift Selector Harness Connector (A) Terminal 1 And Combination Meter Harness Connector (B) Terminal 29

   Courtesy of NISSAN MOTOR CO., U.S.A.
4. Check continuity between CVT shift selector harness connector (A) terminal and ground.
   CONTINUITY REFERENCE CHART
   
   

   Item	Connector	Terminal	Continuity
   CVT shift selector harness connector	M38	1 - ground	No

   OK or NG 

   OK: GO TO 6.

   NG: Repair open circuit or short to ground in harness or connectors.

Check continuity between CVT shift selector harness connector terminal and ground.

OK or NG 

OK: INSPECTION END 

NG: Repair open circuit in harness or connectors.

Fig 2: Checking Continuity Between CVT Shift Selector Harness Connector Terminal 2 And Ground

Courtesy of NISSAN MOTOR CO., U.S.A.

1. Turn ignition switch OFF.
2. Disconnect CVT shift selector connector and combination meter connector.
3. Check continuity between CVT shift selector harness connector (A) terminal and combination meter harness connector (B) terminal.
   CONTINUITY REFERENCE CHART
   
   

   Item	Connector	Terminal	Continuity
   CVT shift selector harness connector	M38	1	Yes
   Combination meter harness connector	M24	29

   Fig 3: Checking Continuity Between CVT Shift Selector Harness Connector (A) Terminal 1 And Combination Meter Harness Connector (B) Terminal 29

   Courtesy of NISSAN MOTOR CO., U.S.A.
4. Check continuity between CVT shift selector harness connector terminal and ground.
   CONTINUITY REFERENCE CHART
   
   

   Item	Connector	Terminal	Continuity
   CVT shift selector harness connector	M38	1 - ground	Yes

   OK or NG 

   OK: GO TO  6.

   NG: Repair open circuit or short to ground in harness or connectors.

Check continuity between CVT shift selector harness connector terminal and ground.

Fig 4: Checking Continuity Between CVT Shift Selector Harness Connector Terminal 2 And Ground

Courtesy of NISSAN MOTOR CO., U.S.A.

OK or NG 

OK: INSPECTION END 

NG: Repair open circuit in harness or connectors.