LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Nissan-Datsun >> 2003 >> Sentra SE-R, Automatic >> Repair and Diagnosis >> External Pages >> Different car >> Section 2075 (Automatic Air Conditioner) >> Trouble Diagnosis >> Intake Sensor Circuit >> Diagnostic Procedure For Intake Sensor
July 1: So it begins. Don't worry, this is not in the correct legal jurisdiction!

Diagnostic Procedure For Intake Sensor

WARNING: This page is about a different car, the 2007 Nissan Quest. However, it is still accessible from the selected car via links, so may be relevant.

SYMPTOM: Intake sensor circuit is open or shorted. Using the CONSULT-II, DTC B2581 or B2582 is displayed. Without a CONSULT-II, code 56 or 57 is indicated on front air control as a result of conducting the front air control self-diagnosis.

Fig 1: Intake Sensor Circuit Diagram
G04908396Courtesy of NISSAN MOTOR CO., U.S.A.
  1. CHECK VOLTAGE BETWEEN INTAKE SENSOR AND GROUND 
    1. Disconnect intake sensor connector.
    2. Turn ignition switch ON.
    3. Check voltage between intake sensor harness connector M305 terminal 2 and ground.

      Approx. 5V 

    OK or NG 

    OK: GO TO 2.

    NG: GO TO  4.

    Fig 2: Checking Voltage Between Intake Sensor Connector M305 Terminal 2 And Ground
    G04908397Courtesy of NISSAN MOTOR CO., U.S.A.
  2. CHECK CIRCUIT CONTINUITY BETWEEN INTAKE SENSOR AND FRONT AIR CONTROL 
    1. Turn ignition switch OFF.
    2. Disconnect front air control connector.
    3. Check continuity between intake sensor harness connector M305 (B) terminal 1 and front air control harness connector M49 (A) terminal 26.

      Continuity should exist. 

    OK or NG 

    OK: GO TO 3.

    NG: Repair harness or connector.

    Fig 3: Checking Continuity Between Intake Sensor Harness Connector M305 Terminal 1 And Connector M49 Terminal 26
    G04908398Courtesy of NISSAN MOTOR CO., U.S.A.
  3. CHECK INTAKE SENSOR 

    Check intake sensor. Refer to "INTAKE SENSOR ".

    OK or NG 

    OK >>

    1. Replace front air control. Refer to "FRONT AIR CONTROL ".
    2. Go to "A/C SYSTEM SELF-DIAGNOSIS FUNCTION " and perform self-diagnosis.

    NG >>

    1. Replace intake sensor. Refer to "INTAKE SENSOR ".
    2. Go to "A/C SYSTEM SELF-DIAGNOSIS FUNCTION " and perform self-diagnosis.
  4. CHECK CIRCUIT CONTINUITY BETWEEN INTAKE SENSOR AND FRONT AIR CONTROL 
    1. Turn ignition switch OFF.
    2. Disconnect front air control connector.
    3. Check continuity between intake sensor harness connector M305 (B) terminal 2 and front air control harness connector M49 (A) terminal 11.

      Continuity should exist. 

    4. Check continuity between intake sensor harness connector M305 (B) terminal 2 and ground.

      Continuity should not exist. 

      Fig 4: Checking Continuity Between Intake Sensor Harness Connector M305 (B) Terminal 2 And Front Air Control Harness Connector M49 (A) Terminal 11, And Between Connector M305 Terminal 2 And Ground
      G04908399Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG 

    OK >>

    1. Replace front air control. Refer to "FRONT AIR CONTROL ".
    2. Go to "A/C SYSTEM SELF-DIAGNOSIS FUNCTION " and perform self-diagnosis.

    NG: Repair harness or connector.

scientia non olet · About LEMON Manuals