Manual Trans: Overhaul
- General Information
- Special Tools
- Transaxle (Transmission)
- Disassembly And Assembly
- Notes
- Disassembly Service Points
- << A >> Sealing Cap Removal
- << B >> Transaxle Case Removal
- << C >> Spring Pin Removal
- << D >> 3RD-4TH Speed Shift Rail/3RD-4TH Speed Shift Fork/5TH Speed-Reverse Shift Rail/5TH Speed-Reverse Shift Fork Removal
- << E >> 3RD-4TH Speed Shift Rail/3RD-4TH Speed Shift Fork/5TH-Reverse Speed Shift Rail/5TH-Reverse Speed Shift Fork Removal
- << F >> Input Shaft And Output Shaft Removal
- << G >> Differential/Output Shaft/Input Shaft Removal
- Adjustment Before Assembly
- Assembly Service Points
- >>A<< Output Shaft/Input Shaft Installation
- >>B<< Input Shaft/Output Shaft/Differential Installation
- >>C<< 5TH Speed-Reverse Shift Fork/5TH Speed-Reverse Shift Rail/3RD-4TH Speed Shift Fork/3RD-4TH Speed Shift Rail Installation
- >>D<< 5TH-Reverse Speed Shift Fork/5TH-Reverse Speed Shift Rail/3RD-4TH Speed Shift Fork/3RD-4TH Speed Shift Rail Installation
- >>E<< Spring Pin Installation
- >>F<< Spacer And Outer Race Installation
- >>G<< Transaxle Case Installation
- >>H<< Transaxle Case Installation
- >>I<< Sealing Cap Installation
- >>J<< Under Cover Installation
- >>K<< Control Housing Installation
- >>L<< Speedometer Gear Installation
- >>M<< Select Lever Installation
- Inspection
- Disassembly And Assembly
- Input Shaft
- Disassembly And Assembly
- Notes
- Disassembly Service Points
- Assembly Service Points
- >>A<< Oil Seal Installation
- >>B<< Ball Bearing Installation
- >>C<< Snap Ring Installation
- >>D<< Synchronizer Spring Installation
- >>E<< Synchronizer Ring Installation
- >>F<< 3RD-4TH Speed Synchronizer Hub Installation
- >>G<< Synchronizer Sleeve Installation
- >>H<< 4TH Speed Gear Sleeve Installation
- >>J<< 5TH Speed Gear Installation
- >>J<< Thrust Plate Installation
- >>K<< Thrust Plate Stopper Installation
- >>L<< Ball Bearing Installation
- >>M<< Snap Ring Installation
- Inspection
- Disassembly And Assembly
- Output Shaft
- Disassembly And Assembly
- Notes
- Disassembly Service Points
- << A >> Ball Bearing Removal
- << B >> Taper Roller Bearing Removal
- << C >> Reverse Gear Bearing Sleeve Removal
- << D >> 5TH Speed-Reverse Synchronizer Hub Removal
- << E >> 3RD Speed Gear Removal
- << F >> 2ND Speed Gear Sleeve Removal
- << G >> 1ST Speed Gear Sleeve Removal
- << H >> Roller Bearing Inner Race Removal
- << I >> Taper Roller Bearing Removal
- Assembly Service Points
- >>A<< Oil Seal Installation
- >>B<< Roller Bearing Inner Race Installation
- >>C<< Taper Roller Bearing Installation
- >>D<< Snap Ring Installation
- >>E<<1ST Speed Gear Sleeve Installation
- >>F<< Synchronizer Spring Installation
- >>G<< 1ST-2ND Speed Synchronizer Hub Installation
- >>H<< Synchronizer Sleeve Installation
- >>I<< 2ND Speed Gear Sleeve Installation
- >>J<< 3RD Speed Gear Installation
- >>K<< Snap Ring Installation
- >>L<< 4TH Speed Gear Installation
- >>M<< 5TH Speed Gear Sleeve Installation
- >>N<< Synchronizer Spring Installation
- >>O<< Synchronizer Ring Installation
- >>P<< 5TH Speed-Reverse Synchronizer Hub Installation
- >>Q<< Reverse Gear Sleeve Installation
- >>R<< Ball Bearing Installation
- >>S<< Taper Roller Bearing Installation
- >>T<< Snap Ring Installation
- Inspection
- Disassembly And Assembly
- Reverse Idler Gear
- Speedometer Gear
- Select Lever
- Control Housing
- Clutch Housing
- Transmission Case
- Differential
- Specifications