Transmission DTCS
TRANSMISSION DTCS 722.6/9 (VGSNAG2)
| MB DTC | Description |
| 0218 | The oil temperature of the transmission is too high. |
| 0513 | No CAN message was received from control unit 'Central gateway'. |
| 0562 | The power supply of circuit 87 has undervoltage. |
| 0563 | The power supply of circuit 87 has overvoltage. |
| 0601 | An incorrect variant coding or configuration was detected. |
| 0602 | Control unit 'Y3/8n4 (Fully integrated transmission control, control unit)' is not coded. |
| 0604 | There is an internal control unit fault in the RAM memory. |
| 0605 | There is an internal control unit fault in the ROM memory. |
| 0606 | Component 'Y3/8n4 (Fully integrated transmission control, control unit)' is faulty. |
| 0607 | The control unit has a malfunction. |
| 060A | Component 'Y3/8n4 (Fully integrated transmission control, control unit)' is defective. |
| 060C | There is an internal control unit fault in the central processing unit. |
| 0613 | The processor in control unit "Transmission" has a malfunction. |
| 061B | Component 'Y3/8n4 (Fully integrated transmission control, control unit)' is defective. |
| 062F | There is an internal error in the EEPROM of the control unit. |
| 0633 | The control unit is not personalized. |
| 0641 | Output 1 for the reference voltage of the sensors has an electrical fault or an open circuit. |
| 0642 | The power supply of the rpm sensors is faulty. |
| 0643 | The power supply of the rpm sensors is faulty. |
| 0651 | Component 'Y3/8n4 (Fully integrated transmission control, control unit)' is defective. |
| 06A3 | Component 'Y3/8n4 (Fully integrated transmission control, control unit)' is defective. |
| 0701 | Control unit "Transmission" has a malfunction. |
| 0705 | Selection range sensor A has an electrical fault. |
| 0706 | Selection range sensor A has a malfunction. |
| 0711 | Component 'Y3/8n4 (Fully integrated transmission control, control unit)' is defective. |
| 0712 | Transmission oil temperature sensor 1 has a short circuit to ground. |
| 0713 | Transmission oil temperature sensor 1 has a short circuit to positive. |
| 0714 | Component 'Y3/8n4 (Fully integrated transmission control, control unit)' is defective. |
| 0716 | Overspeeding of the transmission input shaft |
| 0717 | The signal from the rpm sensor 'Turbine wheel' is missing. |
| 0718 | The rpm sensor 'Turbine wheel' has a sporadic malfunction. |
| 0720 | Mechanical defect in automatic transmission |
| 0721 | The output speed signal of the automatic transmission is implausible compared to the wheel speed signal. |
| 0722 | The signal of rpm sensor "Output shaft" is missing. |
| 0723 | Rpm sensor "Output shaft" has a sporadic malfunction. |
| 0729 | Gear 6 is implausible or the transmission is slipping. |
| 0731 | Gear 1 is implausible or the transmission is slipping. |
| 0732 | Gear 2 is implausible or the transmission is slipping. |
| 0733 | Gear 3 is implausible or the transmission is slipping. |
| 0734 | Gear 4 is implausible or the transmission is slipping. |
| 0735 | Gear 5 is implausible or the transmission is slipping. |
| 0741 | Actuation of the torque converter lockup clutch is not possible. |
| 0742 | The torque converter lock-up clutch causes impermissible closing. |
| 0748 | Pressure regulating valve 1 has an electrical fault. |
| 076F | Gear 7 is implausible or the transmission is slipping. |
| 0778 | Pressure regulating valve 2 has an electrical fault. |
| 0798 | Pressure regulating valve 3 has an electrical fault. |
| 0841 | Oil pressure sensor 'A' has a malfunction. |
| 0842 | Component 'Pressure sensor' or its power supply has an open circuit or short circuit to ground. |
| 0843 | Component 'Pressure sensor' or its power supply has an open circuit or short circuit to positive. |
| 0893 | Hydraulic fault in transmission |
| 0894 | The transmission is slipping. |
| 0944 | Check component 'Auxiliary oil pump'. |
| 0949 | The teach in of the transmission positions is incomplete. |
| 1240 | The CAN bus has a malfunction. |
| 1242 | The CAN message from the control unit 'CRUISE CONTROL' is invalid or implausible. |
| 1610 | Component 'Y3/8n4 (Fully integrated transmission control, control unit)' is defective. |
| 1629 | Component 'Y3/8n4 (Fully integrated transmission control, control unit)' is defective. |
| 1631 | Component 'Y3/8n4 (Fully integrated transmission control, control unit)' is defective. |
| 1632 | Component 'Y3/8n4 (Fully integrated transmission control, control unit)' is defective. |
| 1633 | An internal control unit fault has triggered a program abort. |
| 1634 | Component 'Y3/8n4 (Fully integrated transmission control, control unit)' is defective. |
| 1636 | Component 'Y3/8n4 (Fully integrated transmission control, control unit)' is defective. |
| 1638 | Component 'Y3/8n4 (Fully integrated transmission control, control unit)' is defective. |
| 1639 | Component 'Y3/8n4 (Fully integrated transmission control, control unit)' is defective. |
| 1644 | Variant coding of component 'Y3/8n4 (Fully integrated transmission control, control unit)' has not yet been performed or is faulty. |
| 1693 | Component 'Y3/8n4 (Fully integrated transmission control, control unit)' is defective. |
| 1707 | Shutdown of the transmission function due to the occurrence of overtemperature and (or) overvoltage |
| 1708 | CAN communication with control unit 'A80 (Intelligent servo module for DIRECT SELECT)' has a malfunction. |
| 1709 | CAN communication with control unit 'A80 (Intelligent servo module for DIRECT SELECT)' has a malfunction. |
| 1710 | Component 'Y3/8n4 (Fully integrated transmission control, control unit)' is defective. |
| 1711 | Component 'Y3/8n4 (Fully integrated transmission control, control unit)' is defective. |
| 1712 | Component 'Y3/8n4 (Fully integrated transmission control, control unit)' is defective. |
| 231B | The mixture formation (cylinder 8) is erratic and injector injection quantity adjustment is disabled. |
| 233D | The value of the transmission oil temperature sensor is implausible. |
| 2415 | The signal of oxygen sensor 1 (cylinder bank 2) is implausible. |
| 2638 | The torque reduction requested by the transmission control is rejected by the engine control system. |
| 2711 | Hydraulic fault in transmission |
| 2716 | The internal electrical test of component 'Y3/8y4 (K3 clutch control solenoid valve)' has failed. |
| 2725 | Pressure regulating valve 5 has an electrical fault. |
| 2734 | Pressure regulating valve 6 has an electrical fault. |
| 2759 | The pressure regulating valve of the torque converter lockup clutch has an electrical fault. |
| 2761 | The pressure regulating valve of the torque converter lockup clutch has an electrical fault or an open circuit. |
| 2766 | Rpm sensor 2 'Turbine wheel' has a malfunction. |
| 2767 | The signal from component 'Y3/8n2 (Internal transmission speed rpm sensor)' is unavailable. |
| 2768 | Rpm sensor 2 'Turbine wheel' has a sporadic malfunction. |
| 2783 | The friction power of the torque converter lockup clutch is too high. |
| 2806 | Component 'Y3/8s1 (Selection range sensor)' was not taught in. |
| 2810 | Pressure regulating valve 7 has an electrical fault. |
| C001 | CAN bus OFF fault |
| C002 | CAN bus OFF fault |
| C100 | No CAN message was received from control unit 'Engine control system'. |
| C103 | No CAN message was received from control unit 'N15/5 (Electronic selector lever module control unit)'. |
| C114 | Communication with the control unit 'Transfer case' has a malfunction. |
| C115 | Communication with control unit 'Drivetrain' has a malfunction. |
| C121 | CAN communication with the traction system has a malfunction. |
| C126 | CAN communication with control unit 'N80 (Steering column tube module control unit)' has a malfunction. |
| C132 | No CAN message was received from control unit 'Suspension system'. |
| C141 | CAN communication with control unit 'N73 (Electronic ignition lock control unit)' has a malfunction. |
| C155 | CAN communication with control unit 'A1 (Instrument cluster)' has a malfunction. |
| C164 | CAN communication with control unit 'Air conditioning' has a malfunction. |
| C167 | Communication with the electronic ignition lock has a malfunction. |
| C256 | No CAN message was received from control unit 'DSI'. |
| C300 | Component 'Y3/8n4 (Fully integrated transmission control, control unit)' is defective. |
| C401 | The CAN signals sent from control unit 'Engine control system' are incomplete. |
| C404 | Implausible data were received from the electronic selector lever module. |
| C414 | Implausible data were received from the control unit 'Transfer case'. |
| C415 | The CAN signals sent from control unit 'Traction system' are incomplete. |
| C421 | The CAN signals sent from control unit 'Suspension system' are incomplete. |
| C423 | The CAN signals sent from control unit 'A1 (Instrument cluster)' are incomplete. |
| C424 | The CAN signals sent from control unit 'Air conditioning' are incomplete. |
| C426 | The start enable signal was not issued by control unit 'Drive authorization system'. |
| C428 | No CAN message was received from control unit 'N80 (Steering column tube module control unit)'. |
| C429 | No CAN message was received from control unit 'N80 (Steering column tube module control unit)'. |
| C431 | One or more signals sent from control unit 'N73 (Electronic ignition lock control unit)' via the CAN bus is implausible. |
| C439 | The signal of component 'Off-road operating panel' is implausible. |
| C529 | Communication with the DIRECT SELECT lever has a malfunction. |
| C557 | One or more messages transmitted by control unit 'DSI' via the CAN bus are intermittently not available. |
| C55A | No CAN message was received from control unit 'Engine control system'. |
| C55B | No CAN message was received from control unit 'Engine control system'. |
| C55C | Fault in CAN communication with component 'DSI - DIRECT SELECT interface (N150)'. |
| D10B | No CAN message was received from control unit 'Engine control system'. |
| D138 | CAN communication with component 'Auxiliary oil pump' has a malfunction. |
| D139 | No CAN message was received from control unit 'N80 (Steering column tube module control unit)'. |
| D13A | No CAN message was received from control unit 'N80 (Steering column tube module control unit)'. |
| D400 | The value transmitted by the engine control system for the accelerator pedal is not available on the CAN bus. |
| D401 | The engine speed of the engine control system is not available on the CAN bus. |
| D402 | The temperature of the engine control system is not available on the CAN bus. |
| D404 | The engine torque statically specified by the engine control system is not available on the CAN bus. |
| D405 | The minimum engine torque of the engine control system is not available on the CAN bus. |
| D406 | The maximum engine torque of the engine control system is not available on the CAN bus. |
| D407 | The engine torque specified for the traction system and transmitted by the engine control system is not available on the CAN bus. |
| D408 | Signal 'Brake light switch' transmitted by the traction system is not available on the CAN bus. |
| D409 | The left front wheel speed signal from the traction system is not available on the CAN bus. |
| D40A | The right front wheel speed signal from the traction system is not available on the CAN bus. |
| D40B | The left rear wheel speed signal from the traction system is not available on the CAN bus. |
| D40C | The right rear wheel speed signal from the traction system is not available on the CAN bus. |
| D420 | CAN communication with control unit 'N80 (Steering column tube module control unit)' has a malfunction. |
| D504 | One or more signals sent from control unit 'N80 (Steering column tube module control unit)' via the CAN bus is implausible. |
| D505 | The CAN signals sent from control unit 'N78' are incomplete. |
| D507 | The CAN signals sent from control unit 'Engine control system' are incomplete. |
| D508 | CAN communication with component 'N15/5 (Electronic selector lever module control unit)' has a malfunction. |
| D50B | One or more signals sent from control unit 'N15/5 (Electronic selector lever module control unit)' via the CAN bus is implausible. |
| D50C | The CAN signal from component 'M42 (Electric transmission oil pump)' is implausible. |
| D601 | The automatic address allocation or the programming is faulty. |
| D606 | Data record 1 of the software module is missing or faulty. |
| D60E | Component 'Y3/8n4 (Fully integrated transmission control, control unit)' is defective. |
| F000 | Component 'Y3/8n4 (Fully integrated transmission control, control unit)' is defective. |