LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Mercedes Benz >> 2010 >> Sprinter 3500, 2D Cab Chassis Extended >> Repair and Diagnosis >> Quick Lookups >> DTC Index >> DTC Index - Transmission (722.5 5-Speed) >> Transmission DTCS
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Transmission DTCS

TRANSMISSION DTCS (722.6 (5-SPEED)

MB DTC Description Control Module Transmission
P0501 The CAN signal 'Wheel speed' from the control unit 'N30/4 (ESP® control unit)' is faulty. EGS53 722.6 (5-Speed)
P0562 The voltage at circuit 15 of component 'ETC [EGS]' is too low. EGS53 722.6 (5-Speed)
P0563 The voltage at circuit 15 of component 'ETC [EGS]' is too high. EGS53 722.6 (5-Speed)
P0601 The control unit 'ETC [EGS]' has an internal fault. EGS53 722.6 (5-Speed)
P0602 N15/3 (ETC [EGS] control unit) - Invalid coding EGS53 722.6 (5-Speed)
P0604 The control unit 'ETC [EGS]' has an internal fault. EGS53 722.6 (5-Speed)
P0605 The control unit 'ETC [EGS]' has an internal fault. EGS53 722.6 (5-Speed)
P0606 The control unit 'ETC [EGS]' has an internal fault. EGS53 722.6 (5-Speed)
P0607 The control unit 'ETC [EGS]' has an internal fault. EGS53 722.6 (5-Speed)
P0613 The control unit 'ETC [EGS]' has an internal fault. EGS53 722.6 (5-Speed)
P0614 The SCN coding of control unit 'Engine' is implausible compared to the SCN coding of control unit 'ETC [EGS]'. EGS53 722.6 (5-Speed)
P0642 Speed sensors - The supply voltage is too low. EGS53 722.6 (5-Speed)
P0643 Speed sensors - The voltage supply is too high. EGS53 722.6 (5-Speed)
P0657 Solenoid valves - The power supply is faulty. EGS53 722.6 (5-Speed)
P0702 The control unit 'ETC [EGS]' has an internal fault. EGS53 722.6 (5-Speed)
P0710 Y3/6s1 (Starter lockout contact) / Y3/6b1 (Transmission oil temperature sensor) - Signal IMPLAUSIBLE EGS53 722.6 (5-Speed)
P0712 Y3/6s1 (Starter lockout contact) / Y3/6b1 (Transmission oil temperature sensor) - Short circuit to ground EGS53 722.6 (5-Speed)
P0714 Y3/6s1 (Starter lockout contact) / Y3/6b1 (Transmission oil temperature sensor) - Signal IMPLAUSIBLE EGS53 722.6 (5-Speed)
P0717 Y3/6n2 (Rpm sensor 2) - No signal EGS53 722.6 (5-Speed)
P0722 N15/3 (ETC [EGS] control unit) - Rpm sensor ""Output shaft"" has a malfunction. EGS53 722.6 (5-Speed)
P0723 N15/3 (ETC [EGS] control unit) - Rpm sensor ""Output shaft"" has a malfunction. EGS53 722.6 (5-Speed)
P0730 N15/3 (ETC [EGS] control unit) - There is an impermissible transmission ratio. EGS53 722.6 (5-Speed)
P0731 N15/3 (ETC [EGS] control unit) - The gear is implausible or the transmission is slipping (gear 1). EGS53 722.6 (5-Speed)
P0732 N15/3 (ETC [EGS] control unit) - The gear is implausible or the transmission is slipping (gear 2). EGS53 722.6 (5-Speed)
P0733 N15/3 (ETC [EGS] control unit) - The gear is implausible or the transmission is slipping (gear 3). EGS53 722.6 (5-Speed)
P0734 N15/3 (ETC [EGS] control unit) - The gear is implausible or the transmission is slipping (gear 4). EGS53 722.6 (5-Speed)
P0735 N15/3 (ETC [EGS] control unit) - The gear is implausible or the transmission is slipping (gear 5). EGS53 722.6 (5-Speed)
P0741 N15/3 (ETC [EGS] control unit) - Actuation of the torque converter lockup clutch is not possible. EGS53 722.6 (5-Speed)
P0742 N15/3 (ETC [EGS] control unit) - The torque converter lock-up clutch causes impermissible closing. EGS53 722.6 (5-Speed)
P0743 N15/3 (ETC [EGS] control unit) - The internal electrical test of component 'Y3/6y6 (Torque converter lockup PWM solenoid valve)' has failed. EGS53 722.6 (5-Speed)
P0748 N15/3 (ETC [EGS] control unit) - The internal electrical test of component 'Y3/6y1 (Modulating pressure control solenoid valve)' has failed. EGS53 722.6 (5-Speed)
P0752 Y3/6y3 (1-2 and 4-5 gearshift solenoid valve) - Short circuit to ground EGS53 722.6 (5-Speed)
P0753 N15/3 (ETC [EGS] control unit) - The internal electrical test of component 'Y3/6y3 (1-2 and 4-5 gearshift solenoid valve)' has failed. EGS53 722.6 (5-Speed)
P0757 Y3/6y5 (2-3 gearshift solenoid valve) - Short circuit to ground EGS53 722.6 (5-Speed)
P0758 N15/3 (ETC [EGS] control unit) - The internal electrical test of component 'Y3/6y5 (2-3 gearshift solenoid valve)' has failed. EGS53 722.6 (5-Speed)
P0762 Y3/6y4 (3-4 gearshift solenoid valve) - Short circuit to ground EGS53 722.6 (5-Speed)
P0763 N15/3 (ETC [EGS] control unit) - The internal electrical test of component 'Y3/6y4 (3-4 gearshift solenoid valve)' has failed. EGS53 722.6 (5-Speed)
P0778 Y3/6y2 (Shift pressure control solenoid valve) - Short circuit to ground EGS53 722.6 (5-Speed)
P0817 Y3/6s1 (Starter lockout contact) / Y3/6b1 (Transmission oil temperature sensor) - At least one of the components does not function. EGS53 722.6 (5-Speed)
P0822 N15/3 (ETC [EGS] control unit) - The selector lever is in an intermediate position. EGS53 722.6 (5-Speed)
P0824 N15/3 (ETC [EGS] control unit) - The selector lever is in an intermediate position. EGS53 722.6 (5-Speed)
P0914 N15/3 (ETC [EGS] control unit) - The selector lever is in an intermediate position. EGS53 722.6 (5-Speed)
P0928 N15/3 (ETC [EGS] control unit) - Y66/1 (Reversing and parking lock solenoid) EGS53 722.6 (5-Speed)
P1629 The control unit 'ETC [EGS]' has an internal fault. EGS53 722.6 (5-Speed)
P1631 The control unit 'ETC [EGS]' has an internal fault. EGS53 722.6 (5-Speed)
P1632 The control unit 'ETC [EGS]' has an internal fault. EGS53 722.6 (5-Speed)
P1633 The control unit 'ETC [EGS]' has an internal fault. EGS53 722.6 (5-Speed)
P1634 The control unit 'ETC [EGS]' has an internal fault. EGS53 722.6 (5-Speed)
P1636 The control unit 'ETC [EGS]' has an internal fault. EGS53 722.6 (5-Speed)
P1637 The control unit 'ETC [EGS]' has an internal fault. EGS53 722.6 (5-Speed)
P1638 The control unit 'ETC [EGS]' has an internal fault. ( CAN signals ) EGS53 722.6 (5-Speed)
P1639 The control unit 'ETC [EGS]' has an internal fault. ( CAN signals ) EGS53 722.6 (5-Speed)
P1644 N15/3 (ETC [EGS] control unit) - Invalid coding EGS53 722.6 (5-Speed)
P1704 Overspeed of component 'Y3/6n2 (Rpm sensor 2)' has occurred. EGS53 722.6 (5-Speed)
P1705 Overspeed of component 'Y3/6n3 (Rpm sensor 3)' has occurred. EGS53 722.6 (5-Speed)
P1731 N15/3 (ETC [EGS] control unit) - The gear comparison is negative or the target gear is not reached. EGS53 722.6 (5-Speed)
P220B Y3/6n2 (Rpm sensor 2) / Y3/6n3 (Rpm sensor 3) - An overspeed was detected. EGS53 722.6 (5-Speed)
P2502 N15/3 (ETC [EGS] control unit) - The gear is implausible or the transmission is slipping. EGS53 722.6 (5-Speed)
P2603 Speed sensors - The supply voltage fluctuates. EGS53 722.6 (5-Speed)
P2638 N15/3 (ETC [EGS] control unit) - Feedback on the status of the transmission protection is not received. EGS53 722.6 (5-Speed)
P2767 Y3/6n3 (Rpm sensor 3) - No signal EGS53 722.6 (5-Speed)
P2783 Wandler-Uberbruckungskupplung (KUB): ubermige Leistungsaufnahme EGS53 722.6 (5-Speed)
P2784 Y3/6n2 (Rpm sensor 2) / Y3/6n3 (Rpm sensor 3) - The values are implausible. EGS53 722.6 (5-Speed)
U0002 Drive train CAN bus OFF fault EGS53 722.6 (5-Speed)
U0100 CAN communication with component 'Control unit Motor electronics' is faulty. EGS53 722.6 (5-Speed)
U0103 CAN communication with component 'N15/5 (Electronic selector lever module control unit)' is faulty. EGS53 722.6 (5-Speed)
U0114 CAN communication with component 'N133 (All-wheel drive control unit)' is faulty. EGS53 722.6 (5-Speed)
U0121 CAN communication with component 'N30/4 (ESP® control unit)' is faulty. EGS53 722.6 (5-Speed)
U0141 CAN communication with component 'N73 (Electronic ignition lock (EZS) control unit)' is faulty. EGS53 722.6 (5-Speed)
U0155 CAN communication with component 'A1 (Instrument cluster)' is faulty. EGS53 722.6 (5-Speed)
U0164 CAN communication with component 'S98 (Air conditioning pushbutton control module)' is faulty. EGS53 722.6 (5-Speed)
U0401 CAN communication with component 'Control unit Motor electronics' is faulty. EGS53 722.6 (5-Speed)
U0404 CAN signal 'Position Selector lever' from control unit 'N15/5 (Electronic selector lever module control unit)' is missing or implausible. EGS53 722.6 (5-Speed)
U0414 CAN communication with component 'N133 (All-wheel drive control unit)' is faulty. EGS53 722.6 (5-Speed)
U0415 CAN communication with component 'N30/4 (ESP® control unit)' is faulty. EGS53 722.6 (5-Speed)
U0423 CAN communication with component 'A1 (Instrument cluster)' is faulty. EGS53 722.6 (5-Speed)
U0424 CAN communication with component 'S98 (Air conditioning pushbutton control module)' is faulty. EGS53 722.6 (5-Speed)
U0428 CAN signal 'Steering angle' from control unit 'N80 (Steering column tube module control unit)' is missing or implausible. EGS53 722.6 (5-Speed)
U0431 CAN communication with component 'N73 (Electronic ignition lock (EZS) control unit)' is faulty. EGS53 722.6 (5-Speed)
U110B CAN communication with component 'Control unit Motor electronics' is faulty. EGS53 722.6 (5-Speed)
U1118 CAN signal 'Variant coding' from control unit 'N15/5 (Electronic selector lever module control unit)' is missing or implausible. EGS53 722.6 (5-Speed)
U1139 CAN communication with component 'N80 (Steering column module control unit)' is faulty. EGS53 722.6 (5-Speed)
U113A CAN communication with component 'N80 (Steering column module control unit)' is faulty. EGS53 722.6 (5-Speed)
U1400 CAN signal 'Accelerator pedal' from control unit 'Motor electronics' is missing or implausible. EGS53 722.6 (5-Speed)
U1401 CAN signal 'Engine speed' from control unit 'Motor electronics' is missing or implausible. EGS53 722.6 (5-Speed)
U1402 CAN signal 'Engine temperature' from control unit 'Motor electronics' is missing or implausible. EGS53 722.6 (5-Speed)
U1404 CAN signal 'Static engine torque' from control unit 'Motor electronics' is missing or implausible. EGS53 722.6 (5-Speed)
U1405 CAN signal 'Minimum engine torque' from control unit 'Motor electronics' is missing or implausible. EGS53 722.6 (5-Speed)
U1406 CAN signal 'Maximum engine torque' from control unit 'Motor electronics' is missing or implausible. EGS53 722.6 (5-Speed)
U1407 CAN signal 'Specified engine torque' from control unit 'Motor electronics' is missing or implausible. EGS53 722.6 (5-Speed)
U1408 CAN signal 'Switch Brake lights' from control unit 'N30/4 (ESP® control unit)' is missing or implausible. EGS53 722.6 (5-Speed)
U1409 CAN signal 'Left front wheel speed' from control unit 'N30/4 (ESP® control unit)' is missing or implausible. EGS53 722.6 (5-Speed)
U140A CAN signal 'Right front wheel speed' from control unit 'N30/4 (ESP® control unit)' is missing or implausible. EGS53 722.6 (5-Speed)
U140B CAN signal 'Left rear wheel speed' from control unit 'N30/4 (ESP® control unit)' is missing or implausible. EGS53 722.6 (5-Speed)
U140C CAN signal 'Right rear wheel speed' from control unit 'N30/4 (ESP® control unit)' is missing or implausible. EGS53 722.6 (5-Speed)
U140F CAN signal 'Variant coding' from control unit 'Motor electronics' is missing or implausible. EGS53 722.6 (5-Speed)
U1420 CAN signal 'Status of buttons' from control unit 'N80 (Steering column tube module control unit)' is missing or implausible. EGS53 722.6 (5-Speed)
U1505 CAN communication with component 'N133 (All-wheel drive control unit)' is faulty. EGS53 722.6 (5-Speed)
U1507 CAN communication with component 'Control unit Motor electronics' is faulty. EGS53 722.6 (5-Speed)
U1508 CAN communication with component 'N15/5 (Electronic selector lever module control unit)' is faulty. EGS53 722.6 (5-Speed)
U1509 CAN signal 'Variant coding' from control unit 'Motor electronics' is missing or implausible. EGS53 722.6 (5-Speed)
U2301 Drive train CAN bus OFF fault EGS53 722.6 (5-Speed)
U2318 CAN communication with component 'N15/5 (Electronic selector lever module control unit)' is faulty. EGS53 722.6 (5-Speed)
U2338 CAN communication with component 'N80 (Steering column module control unit)' is faulty. EGS53 722.6 (5-Speed)
scientia non olet · About LEMON Manuals