LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Mazda >> 2011 >> RX-8 R3, 1.3 4 >> Repair and Diagnosis >> Engine Performance >> System >> On-Board Diagnostic [Engine Control System] >> DTC P0482
October 30: LEMON manuals on a temporary server, it is slow and having issues, download the manuals you need! Later in November we will switch back to the fast server.

DTC P0482

DTC P0482 Cooling fan relay NO. 4 and NO. 5 control circuit problem
DETECTION CONDITION 
  • The PCM monitors the cooling fan relay NO. 4/NO. 5 control voltage when the PCM turns the cooling fan relay NO. 4/NO. 5 off. If the control voltage is low, the PCM determines that the cooling fan NO. 4/NO. 5 control circuit voltage is low.
  • The PCM monitors the cooling fan relay NO. 4/NO. 5 control voltage when the PCM turns the cooling fan relay NO. 4/NO. 5 on. If the control voltage is high, the PCM determines that the cooling fan NO. 4/NO. 5 control circuit voltage is high.

Diagnostic support note 
  • This is a continuous monitor (other).
  • The MIL does not illuminate.
  • PENDING CODE is available if the PCM detects the above malfunction condition during the first drive cycle.
  • FREEZE FRAME DATA (Mode 2/Mode 12) is not available.
  • The DTC is stored in the PCM memory.
POSSIBLE CAUSE 
  • Cooling fan relay NO. 4/NO. 5 terminal malfunction
  • Short to ground or open circuit in cooling fan relay NO. 4/NO. 5 power supply circuit
    • Short to ground in wiring harness between main relay terminal C and cooling fan relay NO. 4 terminal A
    • Short to ground in wiring harness between main relay terminal C and cooling fan relay NO. 5 terminal A
    • Cooling fan relay NO. 4/NO. 5 related fuse malfunction
    • Open circuit in wiring harness between main relay terminal C and cooling fan relay NO. 4 terminal A
    • Open circuit in wiring harness between main relay terminal C and cooling fan relay NO. 5 terminal A
  • Short to ground in wiring harness between cooling fan relay NO. 4 terminal E and PCM terminal 1R
  • Short to ground in wiring harness between cooling fan relay NO. 5 terminal E and PCM terminal 1R
  • Cooling fan relay NO. 4/NO. 5 malfunction
  • PCM connector or terminals malfunction
  • Short to power supply in wiring harness between cooling fan relay NO. 4 terminal E and PCM terminal 1R
  • Short to power supply in wiring harness between cooling fan relay NO. 5 terminal E and PCM terminal 1R
  • Open circuit in wiring harness between cooling fan relay NO. 4 terminal E and PCM terminal 1R
  • Open circuit in wiring harness between cooling fan relay NO. 5 terminal E and PCM terminal 1R
  • PCM malfunction
G07878123
DIAGNOSTIC PROCEDURE

STEP INSPECTION ACTION
1 VERIFY RELATED REPAIR INFORMATION AVAILABILITY 
  • Verify related Service Bulletins and/or on-line repair information availability.
  • Is any related repair information available?
 Yes Perform repair or diagnosis according to the available repair information.
  • If the vehicle is not repaired, go to the next step.
No Go to the next step.
2 INSPECT COOLING FAN RELAY NO. 4/NO. 5 CONNECTOR FOR POOR CONNECTION 
  • Turn the ignition switch off.
  • Remove the cooling fan relay NO. 4/NO. 5.
  • Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
  • Is there any malfunction?
 Yes Repair or replace the terminal, then go to Step 9.
No Go to the next step.
3 INSPECT COOLING FAN RELAY NO. 4/NO. 5 POWER SUPPLY CIRCUIT FOR SHORT TO GROUND OR OPEN CIRCUIT 
  • Cooling fan relay NO. 4/NO. 5 relay are removed.
  • Turn the ignition switch to the ON position (engine off).
  • Measure the voltage between the following circuits:
    • Cooling fan relay NO. 4 terminal A (wiring harness-side) and body ground
    • Cooling fan relay NO. 5 terminal A (wiring harness-side) and body ground
  • Is the voltage B+  ?
 Yes Go to the next step.
No Inspect the cooling fan relay NO. 4/NO. 5 related fuse.
  • If the fuse is melt:
    • Repair or replace the wiring harness for a possible short to ground.
    • Replace the fuse.
  • If the fuse is deterioration:
    • Replace the fuse.
  • If the fuse is normal:
    • Repair or replace the wiring harness for a possible open circuit

Go to Step 9.
4 INSPECT COOLING FAN RELAY NO. 4/NO. 5 CONTROL CIRCUIT FOR SHORT TO GROUND 
  • Cooling fan relay NO. 4/NO. 5 relay are removed
  • Turn the ignition switch off.
  • Inspect for continuity between the following circuits:
    • Cooling fan relay NO. 4 terminal E (wiring harness-side) and body ground
    • Cooling fan relay NO. 5 terminal E (wiring harness-side) and body ground
  • Is there continuity?
 Yes If the short to ground circuit could be detected:
  • Repair or replace the wiring harness for a possible short to ground.

    If the short to ground circuit could not be detected:

  • Replace the PCM (short to ground in the PCM internal circuit).

    (See PCM REMOVAL/INSTALLATION ).


Go to Step 9.
No Go to the next step.
5 INSPECT COOLING FAN RELAY NO. 4/NO. 5 
  • Inspect the cooling fan relay NO. 4/NO. 5.

    (See RELAY INSPECTION ).

  • Is there any malfunction?
 Yes Replace the cooling fan relay NO. 4/NO. 5, then go to Step 9.
(See RELAY LOCATION ).
No Go to the next step.
6 INSPECT PCM CONNECTOR FOR POOR CONNECTION 
  • Turn the ignition switch off.
  • Disconnect the PCM connector.
  • Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
  • Is there any malfunction?
 Yes Repair or replace the connector and/or terminals, then go to Step 9.
No Go to the next step.
7 INSPECT COOLING FAN RELAY NO. 4/NO. 5 CONTROL CIRCUIT FOR SHORT TO POWER SUPPLY 
  • Cooling fan relay NO. 4/NO. 5 relay are removed and PCM connector is disconnected.
  • Turn the ignition switch to the ON position (engine off).
  • Measure the voltage between the following circuits:
    • Cooling fan relay NO. 4 terminal E (wiring harness-side) and body ground
    • Cooling fan relay NO. 5 terminal E (wiring harness-side) and body ground
  • Is the voltage B+  ?
 Yes Repair or replace the wiring harness for a possible short to power supply, then go to Step 9.
No Go to the next step.
8 INSPECT COOLING FAN RELAY NO. 4/NO. 5 CONTROL CIRCUIT FOR OPEN CIRCUIT 
  • Cooling fan relay NO. 4/NO. 5 relay are removed and PCM connector is disconnected.
  • Turn the ignition switch off.
  • Inspect for continuity between the following circuits:
    • Cooling fan relay NO. 4 terminal E (wiring harness-side) and PCM terminal 1R (wiring harness-side)
    • Cooling fan relay NO. 5 terminal E (wiring harness-side) and PCM terminal 1R (wiring harness-side)
  • Is there continuity?
 Yes Go to the next step.
No Repair or replace the wiring harness for a possible open circuit, then go to the next step.
9 VERIFY TROUBLESHOOTING OF DTC P0482 COMPLETED 
  • Make sure to reconnect all disconnected connectors.
  • Clear the DTC from the PCM memory using the M-MDS.

    (See AFTER REPAIR PROCEDURE ).

  • Perform the KOEO or KOER self test.

    (See KOEO/KOER SELF TEST ).

  • Is the PENDING CODE same as DTC present?
 Yes Replace the PCM, then go to the next step.
(See PCM REMOVAL/INSTALLATION ).
No Go to the next step.
10 VERIFY AFTER REPAIR PROCEDURE 
 Yes Go to the applicable DTC inspection.
(See DTC TABLE ).
No DTC troubleshooting completed.
scientia non olet · About LEMON Manuals