LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Mazda >> 2007 >> 6 Mazdaspeed >> Repair and Diagnosis >> Engine Performance >> System >> On-Board Diagnostic [Engine Control System L3 With TC] >> DTC P2102 >> Diagnostic procedure
October 30: LEMON manuals on a temporary server, it is slow and having issues, download the manuals you need! Later in November we will switch back to the fast server.

Diagnostic procedure

DTC P2102 DIAGNOSTIC PROCEDURE

STEP INSPECTION ACTION
1 VERIFY FREEZE FRAME DATA HAS BEEN RECORDED 
  • Has the FREEZE FRAME DATA been recorded?
 Yes Go to the next step.
No Record FREEZE FRAME DATA on the repair order, then go to the next step.
2 VERIFY RELATED REPAIR INFORMATION AVAILABILITY 
  • Check for related Service Bulletins and/or online repair information availability.
  • Is any related repair information available?
 Yes Perform the repair or diagnosis according to the available repair information.
  • If the vehicle is not repaired, go to the next step.
No Go to the next step.
3 VERIFY RELATED PENDING CODE AND STORED DTCS 
  • Turn ignition switch to OFF, then ON (Engine off).
  • Verify pending and/or stored DTCs using the WDS or equivalent.
  • Is the DTC P2100 also present?
 Yes Go to appropriate the DTC troubleshooting procedure, then go to Step 10.
No Go to the next step.
4 INSPECT THROTTLE BODY CONNECTOR FOR POOR CONNECTION 
  • Turn the ignition switch to off.
  • Disconnect the throttle body connector.
  • Inspect for poor connection (such as damaged, pulled-put pins, corrosion).
  • Is there any malfunction?
 Yes Repair or replace the terminal, then go to Step 10.
No Go to the next step.
5 INSPECT POWER SUPPLY CIRCUIT OF THROTTLE ACTUATOR FOR OPEN CIRCUIT 
  • Turn ignition switch to the ON position (Engine off).
  • Measure the voltage between throttle body terminal F (harness-side) and body ground.
  • Is the voltage B+  ?
 Yes Go to the next step.
No Repair or replace the wiring harness for an open circuit, then go to Step 10.
6 INSPECT POWER SUPPLY CIRCUIT OF THROTTLE ACTUATOR FOR SHORT TO GROUND 
  • Turn the ignition switch to off.
  • Check continuity between throttle body terminal F (harness-side) and body ground.
  • Is there continuity?
 Yes Repair or replace the wiring harness for a short to ground circuit, then go to Step 10.
No Go to the next step.
7 INSPECT PCM CONNECTOR FOR POOR CONNECTION 
  • Turn the ignition switch to off.
  • Disconnect the PCM connector.
  • Inspect for poor connection (such as damaged/pulled-out pins, corrosion).
  • Is there any malfunction?
 Yes Repair or replace the terminal, then go to Step 10.
No Go to the next step.
8 INSPECT CONTROL CIRCUIT OF THROTTLE ACTUATOR FOR OPEN CIRCUIT 
  • Turn the ignition switch to off.
  • Check for continuity between throttle body terminal E (harness-side) and PCM terminal 4AB (harness-side).
  • Is there continuity?
 Yes Repair or replace the wiring harness for an open circuit, then go to Step 10.
No Go to the next step.
9 INSPECT THROTTLE ACTUATOR 
 Yes Go to the next step.
No Replace the throttle body, then go to the next step.
10 VERIFY TROUBLESHOOTING OF DTC P2102 COMPLETED 
  • Make sure to reconnect all disconnected connectors.
  • Turn ignition switch to the ON position (Engine off).
  • Clear the DTC from the PCM memory using the WDS or equivalent.
  • Start engine and warm it up completely.
  • Is the same DTC present?
 Yes Replace the PCM, then go to the next step.
(See PCM REMOVAL/INSTALLATION ).
No Go to the next step.
11 VERIFY AFTER REPAIR PROCEDURE 
 Yes Go to the applicable DTC inspection.
(See DTC TABLE ).
No Troubleshooting completed.
scientia non olet · About LEMON Manuals