Accessory Protocol Interface Module (APIM) DTC Chart - 8-Inch (203 mm) Touchscreen SYNC®
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| C1001:01 | Vision System Camera: General Electrical Failure | REFER to Parking Aid . |
| B108E:01 | Display: General Electrical Failure | GO to Pinpoint Test O . |
| B116A:01 | Handset Microphone: General Electrical Failure | GO to Pinpoint Test R . |
| B1215:00 | External Memory Card: No Sub Type Information | For vehicles with navigation, GO to Pinpoint Test M . For vehicles without navigation, GO to Pinpoint Test H . |
| B1252:11 | USB Port: Circuit Short To Ground | GO to Pinpoint Test H . |
| B12B8:11 | USB Port #2: Circuit Short To Ground |
NOTE:
This DTC refers to USB port #2 on the APIM itself, which is not used. INSPECT the APIM USB port #2 for damage and remove any debris. CLEAR the DTCs. REPEAT the self-test. If DTC B12B8:11 is retrieved again, Refer to APIM HARDWARE TESTING |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test T . |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to Pinpoint Test U . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test V . |
| U0162:00 | Lost Communication With Navigation Display Module: No Sub Type Information | GO to Pinpoint Test O . |
| U016A:00 | Lost Communication With Global Positioning System Module: No Sub Type Information | GO to Pinpoint Test W . |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to Pinpoint Test X . |
| U0238:00 | Lost Communication With Digital Audio Control Module "D": No Sub Type Information | GO to Pinpoint Test Z . |
| U0256:00 | Lost Communication With Front Controls Interface Module "A": No Sub Type Information | GO to Pinpoint Test AB . |
| U0423:00 | Invalid Data Received From Instrument Panel Control Module: No Sub Type Information | RETRIEVE and FOLLOW the other DTCs present in the IPC. |
| U1A00:87 | Private Communication Network: Missing Message | GO to Pinpoint Test N . |
| U2017:45 | Control Module Software #2: Program Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U2017:45 is still present, Refer to APIM HARDWARE TESTING |
| U2017:51 | Control Module Software #2: Not Programmed | PROGRAM the APIM. REFER to Module Configuration . CLEAR the DTC. REPEAT the self-test. If DTC U2017:51 is still present, Refer to APIM HARDWARE TESTING |
| U2017:52 | Control Module Software #2: Not Activated | PROGRAM the APIM. REFER to Module Configuration . CLEAR the DTC. REPEAT the self-test. If DTC U2017:52 is still present, Refer to APIM HARDWARE TESTING |
| U2017:54 | Control Module Software #2: Missing Calibration | PROGRAM the APIM. REFER to Module Configuration . CLEAR the DTC. REPEAT the self-test. If DTC U2017:54 is still present, Refer to APIM HARDWARE TESTING |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | REFER to Module Configuration . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | REFER to Module Configuration . |
| U3000:04 | Control Module: System Internal Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:04 is still present, Refer to APIM HARDWARE TESTING |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:41 is still present, Refer to APIM HARDWARE TESTING |
| U3000:42 | Control Module: General Memory Failure | CLEAR the DTCs. REPEAT the self-test. If DTC U3000:42 is still present, Refer to APIM HARDWARE TESTING |
| U3000:88 | Control Module: Bus Off | REFER to Module Communications Network . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AD . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AE . |