Technical Service Bulletins
- A/C Compressor
- Filtering Refrigerant After Compressor Replacement (98-12-5)
- Identification Of Non-Ford Approved Refrigerants (99-19-6)
- A/C - R-12 To R-134A Retrofit Kit - Factory A/C Only (98-4-8)
- Use Of R-12 Refrigerant Substitutes (96-17-10)
- A/C System Service - List Of Bulletins To Reference (96-15-6)
- Ford Approved Flushing Procedures For A/C System (95-8-1)
- Air Conditioning Adding Refrigerant Oil Service Tip (95-5-12)
- Air Conditioning FS-10 & FX-15 Compressors (94-15-6)
- R-12 Refrigerant Substitutes - Service Tip (94-14-3)
- Engine Hesitation/Stall/Low Eng Temp: Diagnosis (93-24-8)
- Use Of Correct Fluorescent Tracer Dye - Service Tip (93-20-6)
- A/C SLC Refrigerant Fittings Cleaning/New O-Ring Kit (93-6-5)
- New Refrigerant Fitting "O" Rings (91-22-5)
- Air Conditioning - Refrigerant R-12 - Service Tips (91-9-7)
- Accessories Control Systems
- Electrical - Revised Mechanical Hood Lamp Switch To Replace Old Style Mercury Hood Lamp Switch (01-21-6)
- Temp. Gauge Reads Low - Obsolete Temperature Sender (95-13-2)
- Erratic Distance-To-Empty & Fuel Gauge Readings (95-2-3)
- "Mil" Lamp Service Tips (92-4-4)
- Radio Noise/Reception Diagnostic Repair Procedure (92-13-6)
- SRS System Fault Codes 6 & 32 - New CLOCKSPRING (92-6-1)
- Latches - Door - Replacement Required (91-8-4)
- Air Bag, SRS
- Anti-Lock Brakes
- Anti-Theft Systems
- Automatic Trans
- Transmission Flush/Fill Tool Available From Rotunda (99-15-2)
- Transmission Fluid Usage Chart (98-8-8)
- Torque Converter Replacement - Cooling SYS. Cleaning (96-26-12)
- Torque Converter Leak Test Procedure - New Tool (96-24-9)
- New Rotunda Fluid Changer - Service Tip (95-16-10)
- AOD Transmission No 3-4 Upshift Or Slipping 4TH Gear (93-23-18)
- AOD Trans Overdrive Whine - Install Gear Service Set (92-23-6)
- Auxiliary Emission Control Systems
- EXH Gas Oxygen Sensor Silicone Sealer Contamination (93-23-6)
- Non-Deposit Resistance Fuel Injectors:Deposit Formed (93-11-4)
- Rough Idle And Stumble - New Style Fuel Injectors (92-13-4)
- Rough Idle/Stumble - New Fuel Injectors (91-14-3)
- Stalls/Hard Start/High Mount STOPLAMP INOP - Ground (91-12-5)
- 5.0L Eng High Idle/Mil Flashes Intermittently (91-10-6)
- Electronic Control Modules - Damage From Arc Welding (91-7-5)
- Electronic Modules - Damage From Static Electricity (88-13-3)
- Body Interior
- Electrical Diode Identification And Replacements (96-24-6)
- Temp. Gauge Reads Low - Obsolete Temperature Sender (95-13-2)
- Erratic Distance-To-Empty & Fuel Gauge Readings (95-2-3)
- "Mil" Lamp Service Tips (92-4-4)
- Radio Noise/Reception Diagnostic Repair Procedure (92-13-6)
- SRS System Fault Codes 6 & 32 - New CLOCKSPRING (92-6-1)
- A/C Chemical Smell - Clutch Cycling Pressure Switch (91-11-8)
- Latches - Door - Replacement Required (91-8-4)
- Brakes Control Systems
- Clutch
- Communication Devices
- Cooling Fan
- Cooling System (Mechanical)
- Ford Motor Company Position On Engine Coolant Made From Propylene Glycol (96-16-4)
- Use Of Recycled Engine Coolant - Service Tip (95-18-2)
- 5.0L - Revised Oil Pan Gasket Replacement Procedure (95-6-8)
- Engine Hesitation/Stall/Low Eng Temp: Diagnosis (93-24-8)
- Engine Gasket Surface Cleaning Procedures (93-23-14)
- Non-Deposit Resistance Fuel Injectors:Deposit Formed (93-11-4)
- Cooling System - Proper Fluid Concentrations (93-1-10)
- Premature GENL Eng Wear: Grinding Disc Use Not RECMD (92-25-2)
- Rough Idle And Stumble - New Style Fuel Injectors (92-13-4)
- Cruise Control Systems
- Electronic Steering
- Electronic Suspension
- Engine Control Systems
- Whining/Buzzing - Comes Through Speakers Of Entertainment Or Two-Way Radio (02-16-4)
- Fuel Pump Whine/Buzz Noise In Radio Speakers (99-12-9)
- Volatility Related DRIVEABILITY Concerns Service Tip (98-26-2)
- MOTORCRAFT Fuel Injector Cleaning System (94-8-9)
- Engine Hesitation/Stall/Low Eng Temp: Diagnosis (93-24-8)
- Fuel Injectors (Deposit Resistant): Identification (93-7-5)
- Non-Deposit Resistance Fuel Injectors:Deposit Formed (93-11-4)
- Rough Idle And Stumble - New Style Fuel Injectors (92-13-4)
- 5.0L Eng Spark Knock On ACCEL. - New Timing Specs (92-8-8)
- Fuel Injectors Clogged - New Fuel Injector Cleaning (91-19-3)
- Rough Idle/Stumble - New Fuel Injectors (91-14-3)
- Stalls/Hard Start/High Mount STOPLAMP INOP - Ground (91-12-5)
- 5.0L Eng High Idle/Mil Flashes Intermittently (91-10-6)
- Electronic Control Modules - Damage From Arc Welding (91-7-5)
- Electronic Modules - Damage From Static Electricity (88-13-3)
- Entertainment Systems
- Whining/Buzzing - Comes Through Speakers Of Entertainment Or Two-Way Radio (02-16-4)
- Fuel Pump Whine/Buzz Noise In Radio Speakers (99-12-9)
- Radio Noise/Reception Diagnostic Repair Procedure (92-13-6)
- Radio (EPC) Noise Interference: Wire Inspection (92-4-7)
- No Crank - Low State Of Battery Charge (91-10-8)
- Exterior Lights
- Frames, Subframes & Crossmembers
- Front Suspension
- Fuel System
- Whining/Buzzing - Comes Through Speakers Of Entertainment Or Two-Way Radio (02-16-4)
- Volatility Related DRIVEABILITY Concerns Service Tip (98-26-2)
- CALIFORNIA Reformulated Gasoline - Service Tip (96-10-7)
- MOTORCRAFT Fuel Injector Cleaning System (94-8-9)
- Engine Hesitation/Stall/Low Eng Temp: Diagnosis (93-24-8)
- Fuel Injectors (Deposit Resistant): Identification (93-7-5)
- Non-Deposit Resistance Fuel Injectors:Deposit Formed (93-11-4)
- Rough Idle And Stumble - New Style Fuel Injectors (92-13-4)
- Fuel Injectors Clogged - New Fuel Injector Cleaning (91-19-3)
- Fuses & Circuit Breakers
- Gauges & Instrument Panels
- Hazardous Waste Material
- Headlights
- Heated Glass/Defoggers
- HVAC Control Systems
- Climate Control - Repeat Heater Core Failure (01-15-6)
- Filtering Refrigerant After Compressor Replacement (98-12-5)
- Identification Of Non-Ford Approved Refrigerants (99-19-6)
- A/C - R-12 To R-134A Retrofit Kit - Factory A/C Only (98-4-8)
- Use Of R-12 Refrigerant Substitutes (96-17-10)
- A/C System Service - List Of Bulletins To Reference (96-15-6)
- Ford Approved Flushing Procedures For A/C System (95-8-1)
- Air Conditioning Adding Refrigerant Oil Service Tip (95-5-12)
- A/C "O" Ring Removal From Spring Lock Coupling (95-2-2)
- Air Conditioning FS-10 & FX-15 Compressors (94-15-6)
- R-12 Refrigerant Substitutes - Service Tip (94-14-3)
- Engine Hesitation/Stall/Low Eng Temp: Diagnosis (93-24-8)
- Service Parts Return Of Obsolete A/C Filter Kits (93-22-6)
- Use Of Correct Fluorescent Tracer Dye - Service Tip (93-20-6)
- A/C SLC Refrigerant Fittings Cleaning/New O-Ring Kit (93-6-5)
- New Refrigerant Fitting "O" Rings (91-22-5)
- A/C Chemical Smell - Clutch Cycling Pressure Switch (91-11-8)
- Air Conditioning - Refrigerant R-12 - Service Tips (91-9-7)
- Electronic Control Modules - Damage From Arc Welding (91-7-5)
- Electronic Modules - Damage From Static Electricity (88-13-3)
- Ignition Switch/Steering Lock
- Ignition System
- Fuel Economy - Customer Expectations (99-26-9)
- Engine Hesitation/Stall/Low Eng Temp: Diagnosis (93-24-8)
- Non-Deposit Resistance Fuel Injectors:Deposit Formed (93-11-4)
- Rough Idle And Stumble - New Style Fuel Injectors (92-13-4)
- 5.0L Eng Spark Knock On ACCEL. - New Timing Specs (92-8-8)
- Poor Cold Start/Idle/Run - Fuel Recommendations (91-8-13)
- Infotainment
- Interior/Exterior Trim
- Interior/Illumination Lights
- Locking Hubs
- Lubrication System
- Manual Steering
- Mechanical
- Fuel Economy - Customer Expectations (99-26-9)
- 5.0L - Revised Oil Pan Gasket Replacement Procedure (95-6-8)
- 5.0L - New Torque-To-YEILD Cylinder Head Bolts (95-3-10)
- Engine Hesitation/Stall/Low Eng Temp: Diagnosis (93-24-8)
- Engine Gasket Surface Cleaning Procedures (93-23-14)
- Non-Deposit Resistance Fuel Injectors:Deposit Formed (93-11-4)
- Premature GENL Eng Wear: Grinding Disc Use Not RECMD (92-25-2)
- Rough Idle And Stumble - New Style Fuel Injectors (92-13-4)
- 5.0L Eng Spark Knock On ACCEL. - New Timing Specs (92-8-8)
- Poor Cold Start/Idle/Run - Fuel Recommendations (91-8-13)
- Engine Oil Fill Capacities With Oil Filter Change (90-22-12)
- Mechanical - Hydraulic
- Wheels - Proper Lug Torque Procedures - Service Tip (98-5A-4)
- Brakes - Roughness Concern During Brake Application (95-6-2)
- On-Vehicle Caliper Mounted Brake Rotor Machining EQP (94-25-2)
- Intermittent Brake Squeal/Noise - Normal (90-22-6)
- Brake Shudder/Rotor Damage - Torque LUGNUTS Manually (90-19-9)
- Asbestos Brake & Clutch Warnings (83-22-1)
- Memory Modules
- Mirrors
- Paint & Coatings
- Paint Iron Particle Removal/Acid Rain Neutralization (95-6-1)
- Primed Sheet Metal Prep Procedure & MSDS Information (94-23-4)
- Rear View Mirror Detaches From Windshield (94-17-2)
- Exterior CLEARCOAT MICROCHECKING, Hazing Or Peeling (93-8-4)
- Exterior Paint Comprehensive Repair Procedures (91-18-1)
- Paint Codes - Revised 1991 Fleet Color Paint Codes (91-6-2)
- Passive Restraints
- Rear Suspension
- Restraints Control Systems
- Seats
- Sleeper
- Starter
- Steering Column
- Clicking Noise Heard When Turning Steering Wheel (96-23-1)
- Hum Noise From Air Suspension Compressor (94-21-2)
- Power Steering Noise: Purging Air From System (93-7-3)
- Inner Tie Rod In-Vehicle Replacement Procedure (93-13-2)
- Exhaust Noise At Steering Column - Tape Boot Bearing (91-21-6)
- Steering Clicks - Upper Shaft Bearing Pre-Load Adj (91-3-1)
- Steering Control Systems
- Steering Gear
- Steering Linkage
- Sun Roof/T-Top/Convertible Top
- Suspension Control Systems
- System
- Whining/Buzzing - Comes Through Speakers Of Entertainment Or Two-Way Radio (02-16-4)
- Fuel Pump Whine/Buzz Noise In Radio Speakers (99-12-9)
- Volatility Related DRIVEABILITY Concerns Service Tip (98-26-2)
- Fuel Economy - Customer Expectations (99-26-9)
- CALIFORNIA Reformulated Gasoline - Service Tip (96-10-7)
- 5.0L - Revised Oil Pan Gasket Replacement Procedure (95-6-8)
- MOTORCRAFT Fuel Injector Cleaning System (94-8-9)
- Engine Hesitation/Stall/Low Eng Temp: Diagnosis (93-24-8)
- Engine Gasket Surface Cleaning Procedures (93-23-14)
- EXH Gas Oxygen Sensor Silicone Sealer Contamination (93-23-6)
- Fuel Injectors (Deposit Resistant): Identification (93-7-5)
- Non-Deposit Resistance Fuel Injectors:Deposit Formed (93-11-4)
- Premature GENL Eng Wear: Grinding Disc Use Not RECMD (92-25-2)
- Rough Idle And Stumble - New Style Fuel Injectors (92-13-4)
- 5.0L Eng Spark Knock On ACCEL. - New Timing Specs (92-8-8)
- Fuel Injectors Clogged - New Fuel Injector Cleaning (91-19-3)
- Rough Idle/Stumble - New Fuel Injectors (91-14-3)
- Stalls/Hard Start/High Mount STOPLAMP INOP - Ground (91-12-5)
- No Crank - Low State Of Battery Charge (91-10-8)
- 5.0L Eng High Idle/Mil Flashes Intermittently (91-10-6)
- Poor Cold Start/Idle/Run - Fuel Recommendations (91-8-13)
- Electronic Control Modules - Damage From Arc Welding (91-7-5)
- Electronic Modules - Damage From Static Electricity (88-13-3)
- Transmission Control Systems
- Warning Systems
- Wheel Alignment
- Wheels & Tire System
- Wheels - Proper Lug Torque Procedures - Service Tip (98-5A-4)
- Tire Company Phone Numbers For Customer Assistance (98-5-2)
- Clicking Noise Heard When Turning Steering Wheel (96-23-1)
- Hum Noise From Air Suspension Compressor (94-21-2)
- Power Steering Noise: Purging Air From System (93-7-3)
- Inner Tie Rod In-Vehicle Replacement Procedure (93-13-2)
- Brake Shudder/Rotor Damage - Torque LUGNUTS Manually (90-19-9)
- Window Motors & Regulators
- Wiring System (Data Link Connectors, Pwr Dist., Grnd Dist.)
- Wiring - Wire Harness Terminal Repair Kit (99-6-3)
- Electrical - New Terminal Grease For Service (98-24-6)
- Electrical Diode Identification And Replacements (96-24-6)
- Temp. Gauge Reads Low - Obsolete Temperature Sender (95-13-2)
- Erratic Distance-To-Empty & Fuel Gauge Readings (95-2-3)
- Radio Noise/Reception Diagnostic Repair Procedure (92-13-6)
- Radio (EPC) Noise Interference: Wire Inspection (92-4-7)
- No Crank - Low State Of Battery Charge (91-10-8)